Armbian Ubuntu - Khadas Boot - Success??

Connecting to /dev/ttyUSB0, speed 115200
 Escape character: Ctrl-\ (ASCII 28, FS): enabled
Type the escape character followed by C to get back,
or followed by ? to see other options.
----------------------------------------------------
GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 82249

BL2 Built : 14:02:06, Apr 18 2017.
gxl gb6cb79d - xiaobo.gu@droid05

set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 768MHz - PASS
Rank0: 1024MB(auto)-2T-11
Rank1: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x0001b400
Load bl33 from eMMC, src: 0x0003c200, des: 0x01000000, size: 0x000b4200
NOTICE:  BL3-1: v1.0(debug):866a5ea
NOTICE:  BL3-1: Built : 15:50:05, Feb 28 2017
[BL31]: GXL CPU setup!
aml log : bl31 detect secure boot !
mpu_config_enable:ok
[Image: gxl_v1.1.3198-b7f9835 2017-04-17 16:15:21 yun.cai@droid06]
OPS=0x82
64 61 d7 75 8c eb 82 57 c1 92 72 7f [0.344560 Inits done]
secure task start!
high task start!
low task start!
INFO:    BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address = 0x1000000
INFO:    BL3-1: Next image spsr = 0x3c9


U-Boot 2015.01-g633383b (Jun 12 2017 - 19:10:18)

DRAM:  2 GiB
Relocation Offset is: 76ebd000
register usb cfg[0][1] = 0000000077f5cc10
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpu: vpu_clk_gate_init_off
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC:   aml_priv->desc_buf = 0x0000000073ebd6b0
aml_priv->desc_buf = 0x0000000073ebf9e0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
init_part() 293: PART_TYPE_AML
[mmc_init] mmc init success
dtb magic edfe0dd0
start dts,buffer=0000000073ec2220,dt_addr=0000000073ec2220
parts: 10
00:      logo   0000000002000000 1
01:  recovery   0000000002000000 1
02:       rsv   0000000000800000 1
03:       tee   0000000000800000 1
04:     crypt   0000000002000000 1
05:      misc   0000000002000000 1
06:      boot   0000000002000000 1
07:    system   0000000080000000 1
08:     cache   0000000020000000 2
09:      data   ffffffffffffffff 4
init_part() 293: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x27400000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
Unknown command 'cvbs' - try 'help'
hpd_state=0
set hdmitx VIC = 16
config HPLL = 2970000
HPLL: 0xc000027b
config HPLL done
j = 4  vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below  div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-917: calc 53c81f91, store 53c81f91
_verify_dtb_checksum()-917: calc 53c81f91, store 53c81f91
dtb_read()-1039: total valid 2
dtb_read()-1106: do nothing
Net:   dwmac.c9410000amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0

Start read misc partition datas!
info->attemp_times = 0
info->active_slot = 0
info->slot_info[0].bootable = 1
info->slot_info[0].online = 1
info->slot_info[1].bootable = 0
info->slot_info[1].online = 0
info->attemp_times = 0
attemp_times = 0
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=0
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[CANVAS]addr=0x7f851000 width=3840, height=2160
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
gpio: pin GPIOAO_2 (gpio 102) value is 1
chanel error
Product checking: pass!
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
(Re)start USB...
USB0:   USB3.0 XHCI init start
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 1 **
** Bad device usb 2 **
** Bad device usb 3 **
card in
init_part() 278: PART_TYPE_DOS
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 1b
OEM: 534d
Name: 00000
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 14.9 GiB
mmc clock: 50000000
Bus Width: 4-bit
reading s905_autoscript
1545 bytes read in 4 ms (377 KiB/s)
## Executing script at 01020000
** Bad device usb 0 **
** Bad device usb 1 **
** Bad device usb 2 **
** Bad device usb 3 **
reading uInitrd
5147729 bytes read in 228 ms (21.5 MiB/s)
reading zImage
17484288 bytes read in 768 ms (21.7 MiB/s)
reading dtb.img
25652 bytes read in 5 ms (4.9 MiB/s)
[rsvmem] get fdtaddr NULL!
rsvmem - reserve memory

Usage:
rsvmem check                   - check reserved memory
rsvmem dump                    - dump reserved memory

rsvmem check failed
## Loading init Ramdisk from Legacy Image at 13000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    5147665 Bytes = 4.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
load dtb from 0x1000000 ......
## Flattened Device Tree blob at 01000000
   Booting using the fdt blob at 0x1000000
libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
[rsvmem] bl31 reserved memory set addr error.
   Loading Ramdisk to 739c2000, end 73eaac11 ... OK
   Loading Device Tree to 000000001fff6000, end 000000001ffff433 ... OK
fdt_instaboot: no instaboot image

Starting kernel ...

uboot time: 5961306 us
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.0-rc1-next-20170922-amlogics905x (root@user-VirtualBox) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #18 SMP PREEMPT Fri Sep 22 11:53:20 MSK 2017
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] Machine model: Khadas VIM
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000067c00000, size 188 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x0000000077ffffff]
[    0.000000] NUMA: NODE_DATA [mem 0x77fcbc80-0x77fcd77f]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000001000000-0x0000000077ffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000001000000-0x000000000fffffff]
[    0.000000]   node   0: [mem 0x0000000010200000-0x0000000077ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000001000000-0x0000000077ffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv0.2 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] random: fast init done
[    0.000000] percpu: Embedded 23 pages/cpu @ffff800077f6c000 s55832 r8192 d30184 u94208
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 479296
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: root=LABEL=ROOTFS rootflags=data=writeback rw console=ttyAML0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.repair=yes net.ifnames=0 mac=
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Memory: 1699032K/1947648K available (11644K kernel code, 818K rwdata, 3904K rodata, 640K init, 556K bss, 56104K reserved, 192512K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffff000000000000 - 0xffff000008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000   (129022 GB)
[    0.000000]       .text : 0xffff000009080000 - 0xffff000009be0000   ( 11648 KB)
[    0.000000]     .rodata : 0xffff000009be0000 - 0xffff000009fc0000   (  3968 KB)
[    0.000000]       .init : 0xffff000009fc0000 - 0xffff00000a060000   (   640 KB)
[    0.000000]       .data : 0xffff00000a060000 - 0xffff00000a12ca00   (   819 KB)
[    0.000000]        .bss : 0xffff00000a12ca00 - 0xffff00000a1b7a00   (   556 KB)
[    0.000000]     fixed   : 0xffff7dfffe7fd000 - 0xffff7dfffec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffff7e0000000000 - 0xffff800000000000   (  2048 GB maximum)
[    0.000000]               0xffff7e0000040000 - 0xffff7e0001e00000   (    29 MB actual)
[    0.000000]     memory  : 0xffff800001000000 - 0xffff800078000000   (  1904 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[    0.000000]  Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000354] Console: colour dummy device 80x25
[    0.000840] console [tty0] enabled
[    0.000896] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.000917] pid_max: default: 32768 minimum: 301
[    0.000988] Security Framework initialized
[    0.001729] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.002101] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.002137] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.002163] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.016005] ASID allocator initialised with 65536 entries
[    0.023989] Hierarchical SRCU implementation.
[    0.032337] EFI services will not be available.
[    0.040028] smp: Bringing up secondary CPUs ...
[    0.068224] Detected VIPT I-cache on CPU1
[    0.068272] CPU1: Booted secondary processor [410fd034]
[    0.096256] Detected VIPT I-cache on CPU2
[    0.096291] CPU2: Booted secondary processor [410fd034]
[    0.124296] Detected VIPT I-cache on CPU3
[    0.124327] CPU3: Booted secondary processor [410fd034]
[    0.124380] smp: Brought up 1 node, 4 CPUs
[    0.124443] SMP: Total of 4 processors activated.
[    0.124455] CPU features: detected feature: 32-bit EL0 Support
[    0.124581] CPU: All CPU(s) started at EL2
[    0.124605] alternatives: patching kernel code
[    0.125285] devtmpfs: initialized
[    0.129500] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.129567] futex hash table entries: 1024 (order: 5, 131072 bytes)
[    0.133513] xor: measuring software checksum speed
[    0.172280]    8regs     :  2303.000 MB/sec
[    0.212301]    8regs_prefetch:  2053.000 MB/sec
[    0.252332]    32regs    :  2830.000 MB/sec
[    0.292365]    32regs_prefetch:  2379.000 MB/sec
[    0.292375] xor: using function: 32regs (2830.000 MB/sec)
[    0.292394] pinctrl core: initialized pinctrl subsystem
[    0.293100] DMI not present or invalid.
[    0.293370] NET: Registered protocol family 16
[    0.293782] audit: initializing netlink subsys (disabled)
[    0.293881] audit: type=2000 audit(0.292:1): state=initialized audit_enabled=0 res=1
[    0.296467] cpuidle: using governor menu
[    0.297135] vdso: 2 pages (1 code @ ffff000009be6000, 1 data @ ffff00000a065000)
[    0.297165] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.297973] DMA: preallocated 256 KiB pool for atomic allocations
[    0.298114] Serial: AMBA PL011 UART driver
[    0.312757] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.380723] raid6: int64x1  gen()   471 MB/s
[    0.448684] raid6: int64x1  xor()   454 MB/s
[    0.516756] raid6: int64x2  gen()   716 MB/s
[    0.584748] raid6: int64x2  xor()   610 MB/s
[    0.652782] raid6: int64x4  gen()  1030 MB/s
[    0.720844] raid6: int64x4  xor()   752 MB/s
[    0.788918] raid6: int64x8  gen()  1180 MB/s
[    0.856942] raid6: int64x8  xor()   754 MB/s
[    0.925014] raid6: neonx1   gen()   764 MB/s
[    0.993023] raid6: neonx1   xor()   868 MB/s
[    1.061063] raid6: neonx2   gen()  1234 MB/s
[    1.129128] raid6: neonx2   xor()  1234 MB/s
[    1.197173] raid6: neonx4   gen()  1587 MB/s
[    1.265224] raid6: neonx4   xor()  1481 MB/s
[    1.333292] raid6: neonx8   gen()  1697 MB/s
[    1.401315] raid6: neonx8   xor()  1560 MB/s
[    1.401326] raid6: using algorithm neonx8 gen() 1697 MB/s
[    1.401336] raid6: .... xor() 1560 MB/s, rmw enabled
[    1.401346] raid6: using neon recovery algorithm
[    1.401741] ACPI: Interpreter disabled.
[    1.403005] vgaarb: loaded
[    1.403258] SCSI subsystem initialized
[    1.403675] usbcore: registered new interface driver usbfs
[    1.403742] usbcore: registered new interface driver hub
[    1.403821] usbcore: registered new device driver usb
[    1.404178] pps_core: LinuxPPS API ver. 1 registered
[    1.404200] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.404229] PTP clock support registered
[    1.404427] EDAC MC: Ver: 3.0.0
[    1.404702] dmi: Firmware registration failed.
[    1.404896] Advanced Linux Sound Architecture Driver Initialized.
[    1.405666] clocksource: Switched to clocksource arch_sys_counter
[    1.405835] VFS: Disk quotas dquot_6.6.0
[    1.405892] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.406038] pnp: PnP ACPI: disabled
[    1.411191] NET: Registered protocol family 2
[    1.411662] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    1.411824] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    1.412055] TCP: Hash tables configured (established 16384 bind 16384)
[    1.412177] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    1.412234] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    1.412393] NET: Registered protocol family 1
[    1.412696] RPC: Registered named UNIX socket transport module.
[    1.412713] RPC: Registered udp transport module.
[    1.412722] RPC: Registered tcp transport module.
[    1.412732] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.412888] Unpacking initramfs...
[    1.622066] Freeing initrd memory: 5024K
[    1.622772] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    1.623086] kvm [1]: 8-bit VMID
[    1.623102] kvm [1]: IDMAP page: 1bcd000
[    1.623111] kvm [1]: HYP VA range: 800000000000:ffffffffffff
[    1.623758] kvm [1]: Hyp mode initialized successfully
[    1.623868] kvm [1]: vgic-v2@c4304000
[    1.623948] kvm [1]: vgic interrupt IRQ1
[    1.623967] kvm [1]: virtual timer IRQ4
[    1.627513] workingset: timestamp_bits=44 max_order=19 bucket_order=0
[    1.632960] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.633547] NFS: Registering the id_resolver key type
[    1.633587] Key type id_resolver registered
[    1.633598] Key type id_legacy registered
[    1.633613] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.633645] ntfs: driver 2.1.32 [Flags: R/W].
[    1.634000] fuse init (API version 7.26)
[    1.634570] JFS: nTxBlock = 8192, nTxLock = 65536
[    1.639047] SGI XFS with security attributes, no debug enabled
[    1.640074] 9p: Installing v9fs 9p2000 file system support
[    1.640409] ocfs2: Registered cluster interface o2cb
[    1.640598] OCFS2 User DLM kernel interface loaded
[    1.642299] gfs2: GFS2 installed
[    1.644683] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    1.644713] io scheduler noop registered
[    1.644930] io scheduler cfq registered (default)
[    1.644948] io scheduler mq-deadline registered
[    1.644959] io scheduler kyber registered
[    1.651795] soc soc0: Amlogic Meson GXL (S905D) Revision 21:82 (b:2) Detected
[    1.654808] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.656408] c11084c0.serial: ttyAML1 at MMIO 0xc11084c0 (irq = 10, base_baud = 1500000) is a meson_uart
[    1.656842] c81004c0.serial: ttyAML0 at MMIO 0xc81004c0 (irq = 15, base_baud = 1500000) is a meson_uart
[    2.623683] console [ttyAML0] enabled
[    2.627725] c81004e0.serial: ttyAML2 at MMIO 0xc81004e0 (irq = 16, base_baud = 1500000) is a meson_uart
[    2.637805] meson-drm d0100000.vpu: Queued 2 outputs on vpu
[    2.642852] meson-drm d0100000.vpu: Failed to create debugfs directory
[    2.648631] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    2.655149] [drm] No driver support for vblank timestamp query.
[    2.661094] meson-drm d0100000.vpu: CVBS Output connector not available
[    2.693724] meson-dw-hdmi c883a000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy)
[    2.698271] meson-dw-hdmi c883a000.hdmi-tx: registered DesignWare HDMI I2C bus driver
[    2.705930] meson-drm d0100000.vpu: bound c883a000.hdmi-tx (ops meson_dw_hdmi_ops)
[    2.713255] [drm] Cannot find any crtc or sizes
[    2.717952] [drm] Initialized meson 1.0.0 20161109 for d0100000.vpu on minor 0
[    2.730987] loop: module loaded
[    2.733095] mdio-mux-mmioreg c883455c.eth-phy-mux: failed to register mdio-mux bus /soc/periphs@c8834000/eth-phy-mux
[    2.739275] libphy: Fixed MDIO Bus: probed
[    2.743348] tun: Universal TUN/TAP device driver, 1.6
[    2.749001] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    2.753807] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    2.759725] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[    2.766561] igb: Copyright (c) 2007-2014 Intel Corporation.
[    2.772135] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[    2.779842] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    2.785927] sky2: driver version 1.30
[    2.789975] meson8b-dwmac c9410000.ethernet: PTP uses main clock
[    2.795296] meson8b-dwmac c9410000.ethernet: no reset control found
[    2.801674] stmmac - user ID: 0x11, Synopsys ID: 0x37
[    2.806495] meson8b-dwmac c9410000.ethernet: Ring mode enabled
[    2.812274] meson8b-dwmac c9410000.ethernet: DMA HW capability register supported
[    2.819716] meson8b-dwmac c9410000.ethernet: Normal descriptors
[    2.825558] meson8b-dwmac c9410000.ethernet: RX Checksum Offload Engine supported
[    2.832971] meson8b-dwmac c9410000.ethernet: COE Type 2
[    2.838147] meson8b-dwmac c9410000.ethernet: TX Checksum insertion supported
[    2.845132] meson8b-dwmac c9410000.ethernet: Wake-Up On Lan supported
[    2.851546] meson8b-dwmac c9410000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.859548] libphy: stmmac: probed
[    2.863691] VFIO - User Level meta-driver version: 0.3
[    2.869868] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.874379] ehci-pci: EHCI PCI platform driver
[    2.878825] ehci-platform: EHCI generic platform driver
[    2.884152] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.890092] ohci-pci: OHCI PCI platform driver
[    2.894530] ohci-platform: OHCI generic platform driver
[    2.902302] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    2.905091] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 1
[    2.913096] xhci-hcd xhci-hcd.3.auto: hcc params 0x0228f664 hci version 0x100 quirks 0x02010010
[    2.921339] xhci-hcd xhci-hcd.3.auto: irq 37, io mem 0xc9000000
[    2.927689] hub 1-0:1.0: USB hub found
[    2.930907] hub 1-0:1.0: 2 ports detected
[    2.935136] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    2.940284] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 2
[    2.947911] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.956331] hub 2-0:1.0: USB hub found
[    2.959618] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    2.966945] usbcore: registered new interface driver usb-storage
[    2.974062] mousedev: PS/2 mouse device common for all mice
[    2.978842] i2c /dev entries driver
[    2.984431] sdhci: Secure Digital Host Controller Interface driver
[    2.987716] sdhci: Copyright(c) Pierre Ossman
[    2.992176] Synopsys Designware Multimedia Card Interface Driver
[    2.999406] meson-gx-mmc d0072000.mmc: Got CD GPIO
[    3.046224] meson-gx-mmc d0074000.mmc: allocated mmc-pwrseq
[    3.086111] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.086966] leds_pwm pwmleds: unable to request PWM for vim:red:power: -517
[    3.087731] mmc0: new high speed SDHC card at address 0001
[    3.088167] mmcblk0: mmc0:0001 00000 14.9 GiB
[    3.089449]  mmcblk0: p1 p2
[    3.106028] ledtrig-cpu: registered to indicate activity on CPUs
[    3.112100] meson-sm: secure-monitor enabled
[    3.116343] usbcore: registered new interface driver usbhid
[    3.121351] usbhid: USB HID core driver
[    3.125412] platform-mhu c883c404.mailbox: Platform MHU Mailbox registered
[    3.135559] meson-audio-core c1105400.audio: Failed to create debugfs directory
[    3.142891] NET: Registered protocol family 17
[    3.143658] 9pnet: Installing 9P2000 support
[    3.148085] Key type dns_resolver registered
[    3.152809] registered taskstats version 1
[    3.157036] Btrfs loaded, crc32c=crc32c-generic
[    3.164796] mmc1: new HS200 MMC card at address 0001
[    3.165916] mmcblk1: mmc1:0001 8WPD3R 7.28 GiB
[    3.166417] libphy: mdio_mux: probed
[d    3.170225] libphy: mdio_mux: probed
[    3.172563] leds_pwm pwmleds: unable to request PWM for vim:red:power: -517
[    3.173143] scpi_protocol scpi: SCP Protocol 0.0 Firmware 0.0.0 version
[    3.190781] mmcblk1boot0: mmc1:0001 8WPD3R partition 1 4.00 MiB
[    3.196721] mmcblk1boot1: mmc1:0001 8WPD3R partition 2 4.00 MiB
[    3.202449] mmcblk1rpmb: mmc1:0001 8WPD3R partition 3 512 KiB
[    3.205729] scpi_clocks scpi:clocks: failed to register clock 'vcpu'
[    3.205765] scpi_clocks: probe of scpi:clocks failed with error -110
[    3.221268] asoc-simple-card soc:sound: i2s-hifi <-> meson-i2s-dai.4.auto mapping ok
[    3.228328] asoc-simple-card soc:sound: ASoC: no DMI vendor name!
[    3.236465] leds_pwm pwmleds: unable to request PWM for vim:red:power: -517
[    3.241578] hctosys: unable to open rtc device (rtc0)
[    3.246416] ALSA device list:
[    3.249154]   #0: meson-gxl
[    3.252341] Freeing unused kernel memory: 640K
omain-0 init dvfs: 4
[    3.277731] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[    3.420823] leds_pwm pwmleds: unable to request PWM for vim:red:power: -517
[    3.460242] hub 1-1:1.0: USB hub found
[    3.460423] hub 1-1:1.0: 4 ports detected
[    3.465902] leds_pwm pwmleds: unable to request PWM for vim:red:power: -517
[    3.741775] [drm] Cannot find any crtc or sizes
[    4.005796] EXT4-fs (mmcblk0p2): mounted filesystem with writeback data mode. Opts: data=writeback
[    4.360120] systemd[1]: System time before build time, advancing clock.
[    4.397739] NET: Registered protocol family 10
[    4.398592] Segment Routing with IPv6
[    4.424459] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[    4.437260] systemd[1]: Detected architecture arm64.
[    4.443543] systemd[1]: Set hostname to <amlogic>.
[    4.727033] systemd[1]: Reached target Remote File Systems (Pre).
[    4.728316] systemd[1]: Listening on fsck to fsckd communication Socket.
[    4.734507] systemd[1]: Listening on Syslog Socket.
[    4.739220] systemd[1]: Reached target Encrypted Volumes.
[    4.744710] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    4.752175] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    4.759063] systemd[1]: Listening on Journal Socket (/dev/log).
[    4.895925] EXT4-fs (mmcblk0p2): re-mounted. Opts: commit=600,errors=remount-ro

Ubuntu 16.04.3 LTS amlogic ttyAML0

amlogic login: