API tools faq
paste
Guest User

configuration_adv.h

a guest
Jan 3rd, 2018
338
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 57.99 KB | None | 0 0
raw download clone embed print report
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22.  
  23. /**
  24. * Configuration_adv.h
  25. *
  26. * Advanced settings.
  27. * Only change these if you know exactly what you're doing.
  28. * Some of these settings can damage your printer if improperly set!
  29. *
  30. * Basic settings can be found in Configuration.h
  31. *
  32. */
  33. #ifndef CONFIGURATION_ADV_H
  34. #define CONFIGURATION_ADV_H
  35. #define CONFIGURATION_ADV_H_VERSION 010100
  36.  
  37. // @section temperature
  38.  
  39. //===========================================================================
  40. //=============================Thermal Settings ============================
  41. //===========================================================================
  42.  
  43. #if DISABLED(PIDTEMPBED)
  44. #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
  45. #if ENABLED(BED_LIMIT_SWITCHING)
  46. #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
  47. #endif
  48. #endif
  49.  
  50. /**
  51. * Thermal Protection protects your printer from damage and fire if a
  52. * thermistor falls out or temperature sensors fail in any way.
  53. *
  54. * The issue: If a thermistor falls out or a temperature sensor fails,
  55. * Marlin can no longer sense the actual temperature. Since a disconnected
  56. * thermistor reads as a low temperature, the firmware will keep the heater on.
  57. *
  58. * The solution: Once the temperature reaches the target, start observing.
  59. * If the temperature stays too far below the target (hysteresis) for too long (period),
  60. * the firmware will halt the machine as a safety precaution.
  61. *
  62. * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  63. */
  64. #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  65. #define THERMAL_PROTECTION_PERIOD 40 // Seconds
  66. #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
  67.  
  68. /**
  69. * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
  70. * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
  71. * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
  72. * but only if the current temperature is far enough below the target for a reliable test.
  73. *
  74. * If you get false positives for "Heating failed" increase WATCH_TEMP_PERIOD and/or decrease WATCH_TEMP_INCREASE
  75. * WATCH_TEMP_INCREASE should not be below 2.
  76. */
  77. #define WATCH_TEMP_PERIOD 20 // Seconds
  78. #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
  79. #endif
  80.  
  81. /**
  82. * Thermal Protection parameters for the bed are just as above for hotends.
  83. */
  84. #if ENABLED(THERMAL_PROTECTION_BED)
  85. #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
  86. #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
  87.  
  88. /**
  89. * Whenever an M140 or M190 increases the target temperature the firmware will wait for the
  90. * WATCH_BED_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_BED_TEMP_INCREASE
  91. * degrees, the machine is halted, requiring a hard reset. This test restarts with any M140/M190,
  92. * but only if the current temperature is far enough below the target for a reliable test.
  93. *
  94. * If you get too many "Heating failed" errors, increase WATCH_BED_TEMP_PERIOD and/or decrease
  95. * WATCH_BED_TEMP_INCREASE. (WATCH_BED_TEMP_INCREASE should not be below 2.)
  96. */
  97. #define WATCH_BED_TEMP_PERIOD 60 // Seconds
  98. #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
  99. #endif
  100.  
  101. #if ENABLED(PIDTEMP)
  102. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  103. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
  104. //#define PID_EXTRUSION_SCALING
  105. #if ENABLED(PID_EXTRUSION_SCALING)
  106. #define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
  107. #define LPQ_MAX_LEN 50
  108. #endif
  109. #endif
  110.  
  111. /**
  112. * Automatic Temperature:
  113. * The hotend target temperature is calculated by all the buffered lines of gcode.
  114. * The maximum buffered steps/sec of the extruder motor is called "se".
  115. * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
  116. * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
  117. * mintemp and maxtemp. Turn this off by executing M109 without F*
  118. * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
  119. * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
  120. */
  121. #define AUTOTEMP
  122. #if ENABLED(AUTOTEMP)
  123. #define AUTOTEMP_OLDWEIGHT 0.98
  124. #endif
  125.  
  126. // Show Temperature ADC value
  127. // Enable for M105 to include ADC values read from temperature sensors.
  128. //#define SHOW_TEMP_ADC_VALUES
  129.  
  130. /**
  131. * High Temperature Thermistor Support
  132. *
  133. * Thermistors able to support high temperature tend to have a hard time getting
  134. * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP
  135. * will probably be caught when the heating element first turns on during the
  136. * preheating process, which will trigger a min_temp_error as a safety measure
  137. * and force stop everything.
  138. * To circumvent this limitation, we allow for a preheat time (during which,
  139. * min_temp_error won't be triggered) and add a min_temp buffer to handle
  140. * aberrant readings.
  141. *
  142. * If you want to enable this feature for your hotend thermistor(s)
  143. * uncomment and set values > 0 in the constants below
  144. */
  145.  
  146. // The number of consecutive low temperature errors that can occur
  147. // before a min_temp_error is triggered. (Shouldn't be more than 10.)
  148. //#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
  149.  
  150. // The number of milliseconds a hotend will preheat before starting to check
  151. // the temperature. This value should NOT be set to the time it takes the
  152. // hot end to reach the target temperature, but the time it takes to reach
  153. // the minimum temperature your thermistor can read. The lower the better/safer.
  154. // This shouldn't need to be more than 30 seconds (30000)
  155. //#define MILLISECONDS_PREHEAT_TIME 0
  156.  
  157. // @section extruder
  158.  
  159. // Extruder runout prevention.
  160. // If the machine is idle and the temperature over MINTEMP
  161. // then extrude some filament every couple of SECONDS.
  162. //#define EXTRUDER_RUNOUT_PREVENT
  163. #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
  164. #define EXTRUDER_RUNOUT_MINTEMP 190
  165. #define EXTRUDER_RUNOUT_SECONDS 30
  166. #define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
  167. #define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
  168. #endif
  169.  
  170. // @section temperature
  171.  
  172. //These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
  173. //The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
  174. #define TEMP_SENSOR_AD595_OFFSET 0.0
  175. #define TEMP_SENSOR_AD595_GAIN 1.0
  176.  
  177. /**
  178. * Controller Fan
  179. * To cool down the stepper drivers and MOSFETs.
  180. *
  181. * The fan will turn on automatically whenever any stepper is enabled
  182. * and turn off after a set period after all steppers are turned off.
  183. */
  184. //#define USE_CONTROLLER_FAN
  185. #if ENABLED(USE_CONTROLLER_FAN)
  186. //#define CONTROLLER_FAN_PIN FAN1_PIN // Set a custom pin for the controller fan
  187. #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled
  188. #define CONTROLLERFAN_SPEED 255 // 255 == full speed
  189. #endif
  190.  
  191. // When first starting the main fan, run it at full speed for the
  192. // given number of milliseconds. This gets the fan spinning reliably
  193. // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
  194. //#define FAN_KICKSTART_TIME 100
  195.  
  196. // This defines the minimal speed for the main fan, run in PWM mode
  197. // to enable uncomment and set minimal PWM speed for reliable running (1-255)
  198. // if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
  199. //#define FAN_MIN_PWM 50
  200.  
  201. // @section extruder
  202.  
  203. /**
  204. * Extruder cooling fans
  205. *
  206. * Extruder auto fans automatically turn on when their extruders'
  207. * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE.
  208. *
  209. * Your board's pins file specifies the recommended pins. Override those here
  210. * or set to -1 to disable completely.
  211. *
  212. * Multiple extruders can be assigned to the same pin in which case
  213. * the fan will turn on when any selected extruder is above the threshold.
  214. */
  215. #define E0_AUTO_FAN_PIN -1
  216. #define E1_AUTO_FAN_PIN -1
  217. #define E2_AUTO_FAN_PIN -1
  218. #define E3_AUTO_FAN_PIN -1
  219. #define E4_AUTO_FAN_PIN -1
  220. #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
  221. #define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
  222.  
  223. /**
  224. * M355 Case Light on-off / brightness
  225. */
  226. //#define CASE_LIGHT_ENABLE
  227. #if ENABLED(CASE_LIGHT_ENABLE)
  228. //#define CASE_LIGHT_PIN 4 // Override the default pin if needed
  229. #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
  230. #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
  231. #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
  232. //#define MENU_ITEM_CASE_LIGHT // Add a Case Light option to the LCD main menu
  233. #endif
  234.  
  235. //===========================================================================
  236. //============================ Mechanical Settings ==========================
  237. //===========================================================================
  238.  
  239. // @section homing
  240.  
  241. // If you want endstops to stay on (by default) even when not homing
  242. // enable this option. Override at any time with M120, M121.
  243. //#define ENDSTOPS_ALWAYS_ON_DEFAULT
  244.  
  245. // @section extras
  246.  
  247. //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
  248.  
  249. // Dual X Steppers
  250. // Uncomment this option to drive two X axis motors.
  251. // The next unused E driver will be assigned to the second X stepper.
  252. //#define X_DUAL_STEPPER_DRIVERS
  253. #if ENABLED(X_DUAL_STEPPER_DRIVERS)
  254. // Set true if the two X motors need to rotate in opposite directions
  255. #define INVERT_X2_VS_X_DIR true
  256. #endif
  257.  
  258. // Dual Y Steppers
  259. // Uncomment this option to drive two Y axis motors.
  260. // The next unused E driver will be assigned to the second Y stepper.
  261. //#define Y_DUAL_STEPPER_DRIVERS
  262. #if ENABLED(Y_DUAL_STEPPER_DRIVERS)
  263. // Set true if the two Y motors need to rotate in opposite directions
  264. #define INVERT_Y2_VS_Y_DIR true
  265. #endif
  266.  
  267. // A single Z stepper driver is usually used to drive 2 stepper motors.
  268. // Uncomment this option to use a separate stepper driver for each Z axis motor.
  269. // The next unused E driver will be assigned to the second Z stepper.
  270. //#define Z_DUAL_STEPPER_DRIVERS
  271.  
  272. #if ENABLED(Z_DUAL_STEPPER_DRIVERS)
  273.  
  274. // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
  275. // That way the machine is capable to align the bed during home, since both Z steppers are homed.
  276. // There is also an implementation of M666 (software endstops adjustment) to this feature.
  277. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
  278. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
  279. // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
  280. // Play a little bit with small adjustments (0.5mm) and check the behaviour.
  281. // The M119 (endstops report) will start reporting the Z2 Endstop as well.
  282.  
  283. //#define Z_DUAL_ENDSTOPS
  284.  
  285. #if ENABLED(Z_DUAL_ENDSTOPS)
  286. #define Z2_USE_ENDSTOP _XMAX_
  287. #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine/test this value
  288. #endif
  289.  
  290. #endif // Z_DUAL_STEPPER_DRIVERS
  291.  
  292. // Enable this for dual x-carriage printers.
  293. // A dual x-carriage design has the advantage that the inactive extruder can be parked which
  294. // prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
  295. // allowing faster printing speeds. Connect your X2 stepper to the first unused E plug.
  296. //#define DUAL_X_CARRIAGE
  297. #if ENABLED(DUAL_X_CARRIAGE)
  298. // Configuration for second X-carriage
  299. // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
  300. // the second x-carriage always homes to the maximum endstop.
  301. #define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
  302. #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
  303. #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
  304. #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
  305. // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
  306. // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
  307. // without modifying the firmware (through the "M218 T1 X???" command).
  308. // Remember: you should set the second extruder x-offset to 0 in your slicer.
  309.  
  310. // There are a few selectable movement modes for dual x-carriages using M605 S<mode>
  311. // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
  312. // as long as it supports dual x-carriages. (M605 S0)
  313. // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
  314. // that additional slicer support is not required. (M605 S1)
  315. // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
  316. // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
  317. // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
  318.  
  319. // This is the default power-up mode which can be later using M605.
  320. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE
  321.  
  322. // Default settings in "Auto-park Mode"
  323. #define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
  324. #define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
  325.  
  326. // Default x offset in duplication mode (typically set to half print bed width)
  327. #define DEFAULT_DUPLICATION_X_OFFSET 100
  328.  
  329. #endif // DUAL_X_CARRIAGE
  330.  
  331. // Activate a solenoid on the active extruder with M380. Disable all with M381.
  332. // Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
  333. //#define EXT_SOLENOID
  334.  
  335. // @section homing
  336.  
  337. //homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
  338. #define X_HOME_BUMP_MM 5
  339. #define Y_HOME_BUMP_MM 5
  340. #define Z_HOME_BUMP_MM 2
  341. #define HOMING_BUMP_DIVISOR {2, 2, 4} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
  342. //#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
  343.  
  344. // When G28 is called, this option will make Y home before X
  345. //#define HOME_Y_BEFORE_X
  346.  
  347. // @section machine
  348.  
  349. #define AXIS_RELATIVE_MODES {false, false, false, false}
  350.  
  351. // Allow duplication mode with a basic dual-nozzle extruder
  352. //#define DUAL_NOZZLE_DUPLICATION_MODE
  353.  
  354. // By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
  355. #define INVERT_X_STEP_PIN false
  356. #define INVERT_Y_STEP_PIN false
  357. #define INVERT_Z_STEP_PIN false
  358. #define INVERT_E_STEP_PIN false
  359.  
  360. // Default stepper release if idle. Set to 0 to deactivate.
  361. // Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
  362. // Time can be set by M18 and M84.
  363. #define DEFAULT_STEPPER_DEACTIVE_TIME 120
  364. #define DISABLE_INACTIVE_X true
  365. #define DISABLE_INACTIVE_Y true
  366. #define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
  367. #define DISABLE_INACTIVE_E true
  368.  
  369. #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
  370. #define DEFAULT_MINTRAVELFEEDRATE 0.0
  371.  
  372. //#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
  373.  
  374. // @section lcd
  375.  
  376. #if ENABLED(ULTIPANEL)
  377. #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
  378. #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
  379. #endif
  380.  
  381. // @section extras
  382.  
  383. // minimum time in microseconds that a movement needs to take if the buffer is emptied.
  384. #define DEFAULT_MINSEGMENTTIME 20000
  385.  
  386. // If defined the movements slow down when the look ahead buffer is only half full
  387. #define SLOWDOWN
  388.  
  389. // Frequency limit
  390. // See nophead's blog for more info
  391. // Not working O
  392. //#define XY_FREQUENCY_LIMIT 15
  393.  
  394. // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
  395. // of the buffer and all stops. This should not be much greater than zero and should only be changed
  396. // if unwanted behavior is observed on a user's machine when running at very slow speeds.
  397. #define MINIMUM_PLANNER_SPEED 0.05// (mm/sec)
  398.  
  399. // Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
  400. #define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
  401.  
  402. /**
  403. * @section stepper motor current
  404. *
  405. * Some boards have a means of setting the stepper motor current via firmware.
  406. *
  407. * The power on motor currents are set by:
  408. * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2
  409. * known compatible chips: A4982
  410. * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H
  411. * known compatible chips: AD5206
  412. * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
  413. * known compatible chips: MCP4728
  414. * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
  415. * known compatible chips: MCP4451, MCP4018
  416. *
  417. * Motor currents can also be set by M907 - M910 and by the LCD.
  418. * M907 - applies to all.
  419. * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
  420. * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
  421. */
  422. //#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps
  423. //#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
  424. //#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
  425.  
  426. // Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
  427. //#define DIGIPOT_I2C
  428. //#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster
  429. #define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
  430. // Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
  431. #define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO
  432.  
  433. //===========================================================================
  434. //=============================Additional Features===========================
  435. //===========================================================================
  436.  
  437. #define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
  438. #define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
  439. #define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
  440.  
  441. //#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
  442. #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
  443.  
  444. // @section lcd
  445.  
  446. // Include a page of printer information in the LCD Main Menu
  447. //#define LCD_INFO_MENU
  448.  
  449. // Scroll a longer status message into view
  450. //#define STATUS_MESSAGE_SCROLLING
  451.  
  452. // On the Info Screen, display XY with one decimal place when possible
  453. //#define LCD_DECIMAL_SMALL_XY
  454.  
  455. // The timeout (in ms) to return to the status screen from sub-menus
  456. //#define LCD_TIMEOUT_TO_STATUS 15000
  457.  
  458. #if ENABLED(SDSUPPORT)
  459.  
  460. // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
  461. // around this by connecting a push button or single throw switch to the pin defined
  462. // as SD_DETECT_PIN in your board's pins definitions.
  463. // This setting should be disabled unless you are using a push button, pulling the pin to ground.
  464. // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
  465. #define SD_DETECT_INVERTED
  466.  
  467. #define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
  468. #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
  469.  
  470. #define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
  471. // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
  472. // using:
  473. //#define MENU_ADDAUTOSTART
  474.  
  475. /**
  476. * Sort SD file listings in alphabetical order.
  477. *
  478. * With this option enabled, items on SD cards will be sorted
  479. * by name for easier navigation.
  480. *
  481. * By default...
  482. *
  483. * - Use the slowest -but safest- method for sorting.
  484. * - Folders are sorted to the top.
  485. * - The sort key is statically allocated.
  486. * - No added G-code (M34) support.
  487. * - 40 item sorting limit. (Items after the first 40 are unsorted.)
  488. *
  489. * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the
  490. * compiler to calculate the worst-case usage and throw an error if the SRAM
  491. * limit is exceeded.
  492. *
  493. * - SDSORT_USES_RAM provides faster sorting via a static directory buffer.
  494. * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer.
  495. * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
  496. * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
  497. */
  498. //#define SDCARD_SORT_ALPHA
  499.  
  500. // SD Card Sorting options
  501. #if ENABLED(SDCARD_SORT_ALPHA)
  502. #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256).
  503. #define FOLDER_SORTING -1 // -1=above 0=none 1=below
  504. #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code.
  505. #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
  506. #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
  507. #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
  508. #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
  509. #endif
  510.  
  511. // Show a progress bar on HD44780 LCDs for SD printing
  512. //#define LCD_PROGRESS_BAR
  513.  
  514. #if ENABLED(LCD_PROGRESS_BAR)
  515. // Amount of time (ms) to show the bar
  516. #define PROGRESS_BAR_BAR_TIME 2000
  517. // Amount of time (ms) to show the status message
  518. #define PROGRESS_BAR_MSG_TIME 3000
  519. // Amount of time (ms) to retain the status message (0=forever)
  520. #define PROGRESS_MSG_EXPIRE 0
  521. // Enable this to show messages for MSG_TIME then hide them
  522. //#define PROGRESS_MSG_ONCE
  523. // Add a menu item to test the progress bar:
  524. //#define LCD_PROGRESS_BAR_TEST
  525. #endif
  526.  
  527. // This allows hosts to request long names for files and folders with M33
  528. //#define LONG_FILENAME_HOST_SUPPORT
  529.  
  530. // This option allows you to abort SD printing when any endstop is triggered.
  531. // This feature must be enabled with "M540 S1" or from the LCD menu.
  532. // To have any effect, endstops must be enabled during SD printing.
  533. //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
  534.  
  535. #endif // SDSUPPORT
  536.  
  537. /**
  538. * Additional options for Graphical Displays
  539. *
  540. * Use the optimizations here to improve printing performance,
  541. * which can be adversely affected by graphical display drawing,
  542. * especially when doing several short moves, and when printing
  543. * on DELTA and SCARA machines.
  544. *
  545. * Some of these options may result in the display lagging behind
  546. * controller events, as there is a trade-off between reliable
  547. * printing performance versus fast display updates.
  548. */
  549. #if ENABLED(DOGLCD)
  550. // Enable to save many cycles by drawing a hollow frame on the Info Screen
  551. #define XYZ_HOLLOW_FRAME
  552.  
  553. // Enable to save many cycles by drawing a hollow frame on Menu Screens
  554. #define MENU_HOLLOW_FRAME
  555.  
  556. // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
  557. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  558. //#define USE_BIG_EDIT_FONT
  559.  
  560. // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
  561. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  562. //#define USE_SMALL_INFOFONT
  563.  
  564. // Enable this option and reduce the value to optimize screen updates.
  565. // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
  566. //#define DOGM_SPI_DELAY_US 5
  567. #endif // DOGLCD
  568.  
  569. // @section safety
  570.  
  571. // The hardware watchdog should reset the microcontroller disabling all outputs,
  572. // in case the firmware gets stuck and doesn't do temperature regulation.
  573. #define USE_WATCHDOG
  574.  
  575. #if ENABLED(USE_WATCHDOG)
  576. // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
  577. // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
  578. // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
  579. //#define WATCHDOG_RESET_MANUAL
  580. #endif
  581.  
  582. // @section lcd
  583.  
  584. /**
  585. * Babystepping enables movement of the axes by tiny increments without changing
  586. * the current position values. This feature is used primarily to adjust the Z
  587. * axis in the first layer of a print in real-time.
  588. *
  589. * Warning: Does not respect endstops!
  590. */
  591. #define BABYSTEPPING
  592. #if ENABLED(BABYSTEPPING)
  593. // #define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
  594. #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
  595. #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
  596. //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
  597. //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
  598. #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
  599. // Note: Extra time may be added to mitigate controller latency.
  600. #endif
  601.  
  602. // @section extruder
  603.  
  604. // extruder advance constant (s2/mm3)
  605. //
  606. // advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
  607. //
  608. // Hooke's law says: force = k * distance
  609. // Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant
  610. // so: v ^ 2 is proportional to number of steps we advance the extruder
  611. //#define ADVANCE
  612.  
  613. #if ENABLED(ADVANCE)
  614. #define EXTRUDER_ADVANCE_K .0
  615. #define D_FILAMENT 2.85
  616. #endif
  617.  
  618. /**
  619. * Implementation of linear pressure control
  620. *
  621. * Assumption: advance = k * (delta velocity)
  622. * K=0 means advance disabled.
  623. * See Marlin documentation for calibration instructions.
  624. */
  625. #define LIN_ADVANCE
  626.  
  627. #if ENABLED(LIN_ADVANCE)
  628. #define LIN_ADVANCE_K 0
  629.  
  630. /**
  631. * Some Slicers produce Gcode with randomly jumping extrusion widths occasionally.
  632. * For example within a 0.4mm perimeter it may produce a single segment of 0.05mm width.
  633. * While this is harmless for normal printing (the fluid nature of the filament will
  634. * close this very, very tiny gap), it throws off the LIN_ADVANCE pressure adaption.
  635. *
  636. * For this case LIN_ADVANCE_E_D_RATIO can be used to set the extrusion:distance ratio
  637. * to a fixed value. Note that using a fixed ratio will lead to wrong nozzle pressures
  638. * if the slicer is using variable widths or layer heights within one print!
  639. *
  640. * This option sets the default E:D ratio at startup. Use `M900` to override this value.
  641. *
  642. * Example: `M900 W0.4 H0.2 D1.75`, where:
  643. * - W is the extrusion width in mm
  644. * - H is the layer height in mm
  645. * - D is the filament diameter in mm
  646. *
  647. * Example: `M900 R0.0458` to set the ratio directly.
  648. *
  649. * Set to 0 to auto-detect the ratio based on given Gcode G1 print moves.
  650. *
  651. * Slic3r (including Průša Slic3r) produces Gcode compatible with the automatic mode.
  652. * Cura (as of this writing) may produce Gcode incompatible with the automatic mode.
  653. */
  654. #define LIN_ADVANCE_E_D_RATIO 0 // The calculated ratio (or 0) according to the formula W * H / ((D / 2) ^ 2 * PI)
  655. // Example: 0.4 * 0.2 / ((1.75 / 2) ^ 2 * PI) = 0.033260135
  656. #endif
  657.  
  658. // @section leveling
  659.  
  660. // Default mesh area is an area with an inset margin on the print area.
  661. // Below are the macros that are used to define the borders for the mesh area,
  662. // made available here for specialized needs, ie dual extruder setup.
  663. #if ENABLED(MESH_BED_LEVELING)
  664. #define MESH_MIN_X (X_MIN_POS + MESH_INSET)
  665. #define MESH_MAX_X (X_MAX_POS - (MESH_INSET))
  666. #define MESH_MIN_Y (Y_MIN_POS + MESH_INSET)
  667. #define MESH_MAX_Y (Y_MAX_POS - (MESH_INSET))
  668. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  669. #define UBL_MESH_MIN_X (X_MIN_POS + UBL_MESH_INSET)
  670. #define UBL_MESH_MAX_X (X_MAX_POS - (UBL_MESH_INSET))
  671. #define UBL_MESH_MIN_Y (Y_MIN_POS + UBL_MESH_INSET)
  672. #define UBL_MESH_MAX_Y (Y_MAX_POS - (UBL_MESH_INSET))
  673.  
  674. // If this is defined, the currently active mesh will be saved in the
  675. // current slot on M500.
  676. #define UBL_SAVE_ACTIVE_ON_M500
  677. #endif
  678.  
  679. // @section extras
  680.  
  681. //
  682. // G2/G3 Arc Support
  683. //
  684. #define ARC_SUPPORT // Disable this feature to save ~3226 bytes
  685. #if ENABLED(ARC_SUPPORT)
  686. #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment
  687. #define N_ARC_CORRECTION 25 // Number of intertpolated segments between corrections
  688. //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles
  689. //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes
  690. #endif
  691.  
  692. // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
  693. //#define BEZIER_CURVE_SUPPORT
  694.  
  695. // G38.2 and G38.3 Probe Target
  696. // Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
  697. //#define G38_PROBE_TARGET
  698. #if ENABLED(G38_PROBE_TARGET)
  699. #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
  700. #endif
  701.  
  702. // Moves (or segments) with fewer steps than this will be joined with the next move
  703. #define MIN_STEPS_PER_SEGMENT 6
  704.  
  705. // The minimum pulse width (in µs) for stepping a stepper.
  706. // Set this if you find stepping unreliable, or if using a very fast CPU.
  707. #define MINIMUM_STEPPER_PULSE 0 // (µs) The smallest stepper pulse allowed
  708.  
  709. // @section temperature
  710.  
  711. // Control heater 0 and heater 1 in parallel.
  712. //#define HEATERS_PARALLEL
  713.  
  714. //===========================================================================
  715. //================================= Buffers =================================
  716. //===========================================================================
  717.  
  718. // @section hidden
  719.  
  720. // The number of linear motions that can be in the plan at any give time.
  721. // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
  722. #if ENABLED(SDSUPPORT)
  723. #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
  724. #else
  725. #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
  726. #endif
  727.  
  728. // @section serial
  729.  
  730. // The ASCII buffer for serial input
  731. #define MAX_CMD_SIZE 96
  732. #define BUFSIZE 4
  733.  
  734. // Transfer Buffer Size
  735. // To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
  736. // To buffer a simple "ok" you need 4 bytes.
  737. // For ADVANCED_OK (M105) you need 32 bytes.
  738. // For debug-echo: 128 bytes for the optimal speed.
  739. // Other output doesn't need to be that speedy.
  740. // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
  741. #define TX_BUFFER_SIZE 0
  742.  
  743. // Enable an emergency-command parser to intercept certain commands as they
  744. // enter the serial receive buffer, so they cannot be blocked.
  745. // Currently handles M108, M112, M410
  746. // Does not work on boards using AT90USB (USBCON) processors!
  747. //#define EMERGENCY_PARSER
  748.  
  749. // Bad Serial-connections can miss a received command by sending an 'ok'
  750. // Therefore some clients abort after 30 seconds in a timeout.
  751. // Some other clients start sending commands while receiving a 'wait'.
  752. // This "wait" is only sent when the buffer is empty. 1 second is a good value here.
  753. //#define NO_TIMEOUTS 1000 // Milliseconds
  754.  
  755. // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
  756. //#define ADVANCED_OK
  757.  
  758. // @section fwretract
  759.  
  760. // Firmware based and LCD controlled retract
  761. // M207 and M208 can be used to define parameters for the retraction.
  762. // The retraction can be called by the slicer using G10 and G11
  763. // until then, intended retractions can be detected by moves that only extrude and the direction.
  764. // the moves are than replaced by the firmware controlled ones.
  765.  
  766. //#define FWRETRACT //ONLY PARTIALLY TESTED
  767. #if ENABLED(FWRETRACT)
  768. #define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
  769. #define RETRACT_LENGTH 3 //default retract length (positive mm)
  770. #define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change
  771. #define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s)
  772. #define RETRACT_ZLIFT 0 //default retract Z-lift
  773. #define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering)
  774. #define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change)
  775. #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
  776. #endif
  777.  
  778. /**
  779. * Advanced Pause
  780. * Experimental feature for filament change support and for parking the nozzle when paused.
  781. * Adds the GCode M600 for initiating filament change.
  782. * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle.
  783. *
  784. * Requires an LCD display.
  785. * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  786. */
  787. //#define ADVANCED_PAUSE_FEATURE
  788. #if ENABLED(ADVANCED_PAUSE_FEATURE)
  789. #define PAUSE_PARK_X_POS 3 // X position of hotend
  790. #define PAUSE_PARK_Y_POS 3 // Y position of hotend
  791. #define PAUSE_PARK_Z_ADD 10 // Z addition of hotend (lift)
  792. #define PAUSE_PARK_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
  793. #define PAUSE_PARK_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
  794. #define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
  795. #define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
  796. // It is a short retract used immediately after print interrupt before move to filament exchange position
  797. #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
  798. #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
  799. // Longer length for bowden printers to unload filament from whole bowden tube,
  800. // shorter length for printers without bowden to unload filament from extruder only,
  801. // 0 to disable unloading for manual unloading
  802. #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
  803. #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
  804. // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
  805. // Short or zero length for printers without bowden where loading is not used
  806. #define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
  807. #define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
  808. // 0 to disable for manual extrusion
  809. // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
  810. // or until outcoming filament color is not clear for filament color change
  811. #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
  812. #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
  813. #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
  814. // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
  815. //#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
  816. //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
  817. #endif
  818.  
  819. // @section tmc
  820.  
  821. /**
  822. * Enable this section if you have TMC26X motor drivers.
  823. * You will need to import the TMC26XStepper library into the Arduino IDE for this
  824. * (https://github.com/trinamic/TMC26XStepper.git)
  825. */
  826. //#define HAVE_TMCDRIVER
  827.  
  828. #if ENABLED(HAVE_TMCDRIVER)
  829.  
  830. //#define X_IS_TMC
  831. //#define X2_IS_TMC
  832. //#define Y_IS_TMC
  833. //#define Y2_IS_TMC
  834. //#define Z_IS_TMC
  835. //#define Z2_IS_TMC
  836. //#define E0_IS_TMC
  837. //#define E1_IS_TMC
  838. //#define E2_IS_TMC
  839. //#define E3_IS_TMC
  840. //#define E4_IS_TMC
  841.  
  842. #define X_MAX_CURRENT 1000 // in mA
  843. #define X_SENSE_RESISTOR 91 // in mOhms
  844. #define X_MICROSTEPS 16 // number of microsteps
  845.  
  846. #define X2_MAX_CURRENT 1000
  847. #define X2_SENSE_RESISTOR 91
  848. #define X2_MICROSTEPS 16
  849.  
  850. #define Y_MAX_CURRENT 1000
  851. #define Y_SENSE_RESISTOR 91
  852. #define Y_MICROSTEPS 16
  853.  
  854. #define Y2_MAX_CURRENT 1000
  855. #define Y2_SENSE_RESISTOR 91
  856. #define Y2_MICROSTEPS 16
  857.  
  858. #define Z_MAX_CURRENT 1000
  859. #define Z_SENSE_RESISTOR 91
  860. #define Z_MICROSTEPS 16
  861.  
  862. #define Z2_MAX_CURRENT 1000
  863. #define Z2_SENSE_RESISTOR 91
  864. #define Z2_MICROSTEPS 16
  865.  
  866. #define E0_MAX_CURRENT 1000
  867. #define E0_SENSE_RESISTOR 91
  868. #define E0_MICROSTEPS 16
  869.  
  870. #define E1_MAX_CURRENT 1000
  871. #define E1_SENSE_RESISTOR 91
  872. #define E1_MICROSTEPS 16
  873.  
  874. #define E2_MAX_CURRENT 1000
  875. #define E2_SENSE_RESISTOR 91
  876. #define E2_MICROSTEPS 16
  877.  
  878. #define E3_MAX_CURRENT 1000
  879. #define E3_SENSE_RESISTOR 91
  880. #define E3_MICROSTEPS 16
  881.  
  882. #define E4_MAX_CURRENT 1000
  883. #define E4_SENSE_RESISTOR 91
  884. #define E4_MICROSTEPS 16
  885.  
  886. #endif
  887.  
  888. // @section TMC2130
  889.  
  890. /**
  891. * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
  892. *
  893. * You'll also need the TMC2130Stepper Arduino library
  894. * (https://github.com/teemuatlut/TMC2130Stepper).
  895. *
  896. * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
  897. * the hardware SPI interface on your board and define the required CS pins
  898. * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
  899. */
  900. //#define HAVE_TMC2130
  901.  
  902. #if ENABLED(HAVE_TMC2130)
  903.  
  904. // CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
  905. //#define X_IS_TMC2130
  906. //#define X2_IS_TMC2130
  907. //#define Y_IS_TMC2130
  908. //#define Y2_IS_TMC2130
  909. //#define Z_IS_TMC2130
  910. //#define Z2_IS_TMC2130
  911. //#define E0_IS_TMC2130
  912. //#define E1_IS_TMC2130
  913. //#define E2_IS_TMC2130
  914. //#define E3_IS_TMC2130
  915. //#define E4_IS_TMC2130
  916.  
  917. /**
  918. * Stepper driver settings
  919. */
  920.  
  921. #define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
  922. #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
  923. #define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
  924.  
  925. #define X_CURRENT 1000 // rms current in mA. Multiply by 1.41 for peak current.
  926. #define X_MICROSTEPS 16 // 0..256
  927.  
  928. #define Y_CURRENT 1000
  929. #define Y_MICROSTEPS 16
  930.  
  931. #define Z_CURRENT 1000
  932. #define Z_MICROSTEPS 16
  933.  
  934. //#define X2_CURRENT 1000
  935. //#define X2_MICROSTEPS 16
  936.  
  937. //#define Y2_CURRENT 1000
  938. //#define Y2_MICROSTEPS 16
  939.  
  940. //#define Z2_CURRENT 1000
  941. //#define Z2_MICROSTEPS 16
  942.  
  943. //#define E0_CURRENT 1000
  944. //#define E0_MICROSTEPS 16
  945.  
  946. //#define E1_CURRENT 1000
  947. //#define E1_MICROSTEPS 16
  948.  
  949. //#define E2_CURRENT 1000
  950. //#define E2_MICROSTEPS 16
  951.  
  952. //#define E3_CURRENT 1000
  953. //#define E3_MICROSTEPS 16
  954.  
  955. //#define E4_CURRENT 1000
  956. //#define E4_MICROSTEPS 16
  957.  
  958. /**
  959. * Use Trinamic's ultra quiet stepping mode.
  960. * When disabled, Marlin will use spreadCycle stepping mode.
  961. */
  962. #define STEALTHCHOP
  963.  
  964. /**
  965. * Let Marlin automatically control stepper current.
  966. * This is still an experimental feature.
  967. * Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
  968. * then decrease current by CURRENT_STEP until temperature prewarn is cleared.
  969. * Adjusting starts from X/Y/Z/E_CURRENT but will not increase over AUTO_ADJUST_MAX
  970. * Relevant g-codes:
  971. * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given.
  972. * M906 S1 - Start adjusting current
  973. * M906 S0 - Stop adjusting current
  974. * M911 - Report stepper driver overtemperature pre-warn condition.
  975. * M912 - Clear stepper driver overtemperature pre-warn condition flag.
  976. */
  977. //#define AUTOMATIC_CURRENT_CONTROL
  978.  
  979. #if ENABLED(AUTOMATIC_CURRENT_CONTROL)
  980. #define CURRENT_STEP 50 // [mA]
  981. #define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
  982. #define REPORT_CURRENT_CHANGE
  983. #endif
  984.  
  985. /**
  986. * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
  987. * This mode allows for faster movements at the expense of higher noise levels.
  988. * STEALTHCHOP needs to be enabled.
  989. * M913 X/Y/Z/E to live tune the setting
  990. */
  991. //#define HYBRID_THRESHOLD
  992.  
  993. #define X_HYBRID_THRESHOLD 100 // [mm/s]
  994. #define X2_HYBRID_THRESHOLD 100
  995. #define Y_HYBRID_THRESHOLD 100
  996. #define Y2_HYBRID_THRESHOLD 100
  997. #define Z_HYBRID_THRESHOLD 4
  998. #define Z2_HYBRID_THRESHOLD 4
  999. #define E0_HYBRID_THRESHOLD 30
  1000. #define E1_HYBRID_THRESHOLD 30
  1001. #define E2_HYBRID_THRESHOLD 30
  1002. #define E3_HYBRID_THRESHOLD 30
  1003. #define E4_HYBRID_THRESHOLD 30
  1004.  
  1005. /**
  1006. * Use stallGuard2 to sense an obstacle and trigger an endstop.
  1007. * You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
  1008. * If used along with STEALTHCHOP, the movement will be louder when homing. This is normal.
  1009. *
  1010. * X/Y_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
  1011. * Higher values make the system LESS sensitive.
  1012. * Lower value make the system MORE sensitive.
  1013. * Too low values can lead to false positives, while too high values will collide the axis without triggering.
  1014. * It is advised to set X/Y_HOME_BUMP_MM to 0.
  1015. * M914 X/Y to live tune the setting
  1016. */
  1017. //#define SENSORLESS_HOMING
  1018.  
  1019. #if ENABLED(SENSORLESS_HOMING)
  1020. #define X_HOMING_SENSITIVITY 19
  1021. #define Y_HOMING_SENSITIVITY 19
  1022. #endif
  1023.  
  1024. /**
  1025. * You can set your own advanced settings by filling in predefined functions.
  1026. * A list of available functions can be found on the library github page
  1027. * https://github.com/teemuatlut/TMC2130Stepper
  1028. *
  1029. * Example:
  1030. * #define TMC2130_ADV() { \
  1031. * stepperX.diag0_temp_prewarn(1); \
  1032. * stepperX.interpolate(0); \
  1033. * }
  1034. */
  1035. #define TMC2130_ADV() { }
  1036.  
  1037. #endif // HAVE_TMC2130
  1038.  
  1039. // @section L6470
  1040.  
  1041. /**
  1042. * Enable this section if you have L6470 motor drivers.
  1043. * You need to import the L6470 library into the Arduino IDE for this.
  1044. * (https://github.com/ameyer/Arduino-L6470)
  1045. */
  1046.  
  1047. //#define HAVE_L6470DRIVER
  1048. #if ENABLED(HAVE_L6470DRIVER)
  1049.  
  1050. //#define X_IS_L6470
  1051. //#define X2_IS_L6470
  1052. //#define Y_IS_L6470
  1053. //#define Y2_IS_L6470
  1054. //#define Z_IS_L6470
  1055. //#define Z2_IS_L6470
  1056. //#define E0_IS_L6470
  1057. //#define E1_IS_L6470
  1058. //#define E2_IS_L6470
  1059. //#define E3_IS_L6470
  1060. //#define E4_IS_L6470
  1061.  
  1062. #define X_MICROSTEPS 16 // number of microsteps
  1063. #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
  1064. #define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
  1065. #define X_STALLCURRENT 1500 // current in mA where the driver will detect a stall
  1066.  
  1067. #define X2_MICROSTEPS 16
  1068. #define X2_K_VAL 50
  1069. #define X2_OVERCURRENT 2000
  1070. #define X2_STALLCURRENT 1500
  1071.  
  1072. #define Y_MICROSTEPS 16
  1073. #define Y_K_VAL 50
  1074. #define Y_OVERCURRENT 2000
  1075. #define Y_STALLCURRENT 1500
  1076.  
  1077. #define Y2_MICROSTEPS 16
  1078. #define Y2_K_VAL 50
  1079. #define Y2_OVERCURRENT 2000
  1080. #define Y2_STALLCURRENT 1500
  1081.  
  1082. #define Z_MICROSTEPS 16
  1083. #define Z_K_VAL 50
  1084. #define Z_OVERCURRENT 2000
  1085. #define Z_STALLCURRENT 1500
  1086.  
  1087. #define Z2_MICROSTEPS 16
  1088. #define Z2_K_VAL 50
  1089. #define Z2_OVERCURRENT 2000
  1090. #define Z2_STALLCURRENT 1500
  1091.  
  1092. #define E0_MICROSTEPS 16
  1093. #define E0_K_VAL 50
  1094. #define E0_OVERCURRENT 2000
  1095. #define E0_STALLCURRENT 1500
  1096.  
  1097. #define E1_MICROSTEPS 16
  1098. #define E1_K_VAL 50
  1099. #define E1_OVERCURRENT 2000
  1100. #define E1_STALLCURRENT 1500
  1101.  
  1102. #define E2_MICROSTEPS 16
  1103. #define E2_K_VAL 50
  1104. #define E2_OVERCURRENT 2000
  1105. #define E2_STALLCURRENT 1500
  1106.  
  1107. #define E3_MICROSTEPS 16
  1108. #define E3_K_VAL 50
  1109. #define E3_OVERCURRENT 2000
  1110. #define E3_STALLCURRENT 1500
  1111.  
  1112. #define E4_MICROSTEPS 16
  1113. #define E4_K_VAL 50
  1114. #define E4_OVERCURRENT 2000
  1115. #define E4_STALLCURRENT 1500
  1116.  
  1117. #endif
  1118.  
  1119. /**
  1120. * TWI/I2C BUS
  1121. *
  1122. * This feature is an EXPERIMENTAL feature so it shall not be used on production
  1123. * machines. Enabling this will allow you to send and receive I2C data from slave
  1124. * devices on the bus.
  1125. *
  1126. * ; Example #1
  1127. * ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
  1128. * ; It uses multiple M260 commands with one B<base 10> arg
  1129. * M260 A99 ; Target slave address
  1130. * M260 B77 ; M
  1131. * M260 B97 ; a
  1132. * M260 B114 ; r
  1133. * M260 B108 ; l
  1134. * M260 B105 ; i
  1135. * M260 B110 ; n
  1136. * M260 S1 ; Send the current buffer
  1137. *
  1138. * ; Example #2
  1139. * ; Request 6 bytes from slave device with address 0x63 (99)
  1140. * M261 A99 B5
  1141. *
  1142. * ; Example #3
  1143. * ; Example serial output of a M261 request
  1144. * echo:i2c-reply: from:99 bytes:5 data:hello
  1145. */
  1146.  
  1147. // @section i2cbus
  1148.  
  1149. //#define EXPERIMENTAL_I2CBUS
  1150. #define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
  1151.  
  1152. // @section extras
  1153.  
  1154. /**
  1155. * Spindle & Laser control
  1156. *
  1157. * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
  1158. * to set spindle speed, spindle direction, and laser power.
  1159. *
  1160. * SuperPid is a router/spindle speed controller used in the CNC milling community.
  1161. * Marlin can be used to turn the spindle on and off. It can also be used to set
  1162. * the spindle speed from 5,000 to 30,000 RPM.
  1163. *
  1164. * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
  1165. * hardware PWM pin for the speed control and a pin for the rotation direction.
  1166. *
  1167. * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
  1168. */
  1169. //#define SPINDLE_LASER_ENABLE
  1170. #if ENABLED(SPINDLE_LASER_ENABLE)
  1171.  
  1172. #define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
  1173. #define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
  1174. #define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
  1175. #define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
  1176. #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
  1177. #define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
  1178. #define SPINDLE_INVERT_DIR false
  1179. #define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
  1180.  
  1181. /**
  1182. * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
  1183. *
  1184. * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
  1185. * where PWM duty cycle varies from 0 to 255
  1186. *
  1187. * set the following for your controller (ALL MUST BE SET)
  1188. */
  1189.  
  1190. #define SPEED_POWER_SLOPE 118.4
  1191. #define SPEED_POWER_INTERCEPT 0
  1192. #define SPEED_POWER_MIN 5000
  1193. #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
  1194.  
  1195. //#define SPEED_POWER_SLOPE 0.3922
  1196. //#define SPEED_POWER_INTERCEPT 0
  1197. //#define SPEED_POWER_MIN 10
  1198. //#define SPEED_POWER_MAX 100 // 0-100%
  1199. #endif
  1200.  
  1201. /**
  1202. * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
  1203. */
  1204. //#define PINS_DEBUGGING
  1205.  
  1206. /**
  1207. * Auto-report temperatures with M155 S<seconds>
  1208. */
  1209. #define AUTO_REPORT_TEMPERATURES
  1210.  
  1211. /**
  1212. * Include capabilities in M115 output
  1213. */
  1214. #define EXTENDED_CAPABILITIES_REPORT
  1215.  
  1216. /**
  1217. * Volumetric extrusion default state
  1218. * Activate to make volumetric extrusion the default method,
  1219. * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter.
  1220. *
  1221. * M200 D0 to disable, M200 Dn to set a new diameter.
  1222. */
  1223. //#define VOLUMETRIC_DEFAULT_ON
  1224.  
  1225. /**
  1226. * Enable this option for a leaner build of Marlin that removes all
  1227. * workspace offsets, simplifying coordinate transformations, leveling, etc.
  1228. *
  1229. * - M206 and M428 are disabled.
  1230. * - G92 will revert to its behavior from Marlin 1.0.
  1231. */
  1232. //#define NO_WORKSPACE_OFFSETS
  1233.  
  1234. /**
  1235. * Set the number of proportional font spaces required to fill up a typical character space.
  1236. * This can help to better align the output of commands like `G29 O` Mesh Output.
  1237. *
  1238. * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0.
  1239. * Otherwise, adjust according to your client and font.
  1240. */
  1241. #define PROPORTIONAL_FONT_RATIO 1.0
  1242.  
  1243. /**
  1244. * Spend 28 bytes of SRAM to optimize the GCode parser
  1245. */
  1246. #define FASTER_GCODE_PARSER
  1247.  
  1248. /**
  1249. * User-defined menu items that execute custom GCode
  1250. */
  1251. //#define CUSTOM_USER_MENUS
  1252. #if ENABLED(CUSTOM_USER_MENUS)
  1253. #define USER_SCRIPT_DONE "M117 User Script Done"
  1254.  
  1255. #define USER_DESC_1 "Home & UBL Info"
  1256. #define USER_GCODE_1 "G28\nG29 W"
  1257.  
  1258. #define USER_DESC_2 "Preheat for PLA"
  1259. #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
  1260.  
  1261. #define USER_DESC_3 "Preheat for ABS"
  1262. #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
  1263.  
  1264. #define USER_DESC_4 "Heat Bed/Home/Level"
  1265. #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
  1266.  
  1267. #define USER_DESC_5 "Home & Info"
  1268. #define USER_GCODE_5 "G28\nM503"
  1269. #endif
  1270.  
  1271. /**
  1272. * Specify an action command to send to the host when the printer is killed.
  1273. * Will be sent in the form '//action:ACTION_ON_KILL', e.g. '//action:poweroff'.
  1274. * The host must be configured to handle the action command.
  1275. */
  1276. //#define ACTION_ON_KILL "poweroff"
  1277.  
  1278. //===========================================================================
  1279. //====================== I2C Position Encoder Settings ======================
  1280. //===========================================================================
  1281.  
  1282. /**
  1283. * I2C position encoders for closed loop control.
  1284. * Developed by Chris Barr at Aus3D.
  1285. *
  1286. * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder
  1287. * Github: https://github.com/Aus3D/MagneticEncoder
  1288. *
  1289. * Supplier: http://aus3d.com.au/magnetic-encoder-module
  1290. * Alternative Supplier: http://reliabuild3d.com/
  1291. *
  1292. * Reilabuild encoders have been modified to improve reliability.
  1293. */
  1294.  
  1295. //#define I2C_POSITION_ENCODERS
  1296. #if ENABLED(I2C_POSITION_ENCODERS)
  1297.  
  1298. #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5
  1299. // encoders supported currently.
  1300.  
  1301. #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200.
  1302. #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. <X|Y|Z|E>_AXIS.
  1303. #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or-
  1304. // I2CPE_ENC_TYPE_ROTARY.
  1305. #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for
  1306. // 1mm poles. For linear encoders this is ticks / mm,
  1307. // for rotary encoders this is ticks / revolution.
  1308. //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper
  1309. // steps per full revolution (motor steps/rev * microstepping)
  1310. //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel.
  1311. #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_NONE // Type of error error correction.
  1312. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the
  1313. // printer will attempt to correct the error; errors
  1314. // smaller than this are ignored to minimize effects of
  1315. // measurement noise / latency (filter).
  1316.  
  1317. #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2.
  1318. #define I2CPE_ENC_2_AXIS Y_AXIS
  1319. #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR
  1320. #define I2CPE_ENC_2_TICKS_UNIT 2048
  1321. //#define I2CPE_ENC_2_TICKS_REV (16 * 200)
  1322. //#define I2CPE_ENC_2_INVERT
  1323. #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_NONE
  1324. #define I2CPE_ENC_2_EC_THRESH 0.10
  1325.  
  1326. #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options
  1327. #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below.
  1328.  
  1329. #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4.
  1330. #define I2CPE_ENC_4_AXIS E_AXIS
  1331.  
  1332. #define I2CPE_ENC_5_ADDR 34 // Encoder 5.
  1333. #define I2CPE_ENC_5_AXIS E_AXIS
  1334.  
  1335. // Default settings for encoders which are enabled, but without settings configured above.
  1336. #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR
  1337. #define I2CPE_DEF_ENC_TICKS_UNIT 2048
  1338. #define I2CPE_DEF_TICKS_REV (16 * 200)
  1339. #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE
  1340. #define I2CPE_DEF_EC_THRESH 0.1
  1341.  
  1342. //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
  1343. // axis after which the printer will abort. Comment out to
  1344. // disable abort behaviour.
  1345.  
  1346. #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
  1347. // for this amount of time (in ms) before the encoder
  1348. // is trusted again.
  1349.  
  1350. /**
  1351. * Position is checked every time a new command is executed from the buffer but during long moves,
  1352. * this setting determines the minimum update time between checks. A value of 100 works well with
  1353. * error rolling average when attempting to correct only for skips and not for vibration.
  1354. */
  1355. #define I2CPE_MIN_UPD_TIME_MS 100 // Minimum time in miliseconds between encoder checks.
  1356.  
  1357. // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
  1358. #define I2CPE_ERR_ROLLING_AVERAGE
  1359.  
  1360. #endif // I2C_POSITION_ENCODERS
  1361.  
  1362. #endif // CONFIGURATION_ADV_H
Advertisement
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!