Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- => run install_linux_fw_sd
- reading install_linux_fw_sd.scr
- 4448 bytes read in 16 ms (271.5 KiB/s)
- ## Executing script at 80800000
- ############################################################
- # Linux firmware install from micro SD #
- ############################################################
- This process will erase your NAND and will install a new
- U-Boot and Linux firmware images on the NAND.
- Press CTRL+C now if you wish to abort or wait 10 seconds
- to continue.
- >> Installing U-Boot boot loader (target will reset)
- reading u-boot-ccimx6ulstarter.imx
- 715776 bytes read in 47 ms (14.5 MiB/s)
- Writing bootstream...OK
- Saving Environment to NAND...
- Erasing redundant NAND...
- Erasing at 0x320000 -- 100% complete.
- Writing to redundant NAND... OK
- resetting ...
- U-Boot dub-2017.03-r1.2+g8d60f53 (Nov 07 2018 - 14:18:11 +0000)
- CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
- CPU: Industrial temperature grade (-40C to 105C) at 38C
- Reset cause: POR
- I2C: ready
- DRAM: 256 MiB
- MCA: HW_VER=1 FW_VER=0.18
- PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
- NAND: 256 MiB
- MMC: FSL_SDHC: 0
- In: serial
- Out: serial
- Err: serial
- Model: Digi International ConnectCore 6UL Starter Board.
- ConnectCore 6UL SOM variant 0x02: Industrial Ultralite 528MHz, 256MB NAND, 256MB DDR3, -40/+85C, Wireless, Bluetooth
- Board: ConnectCore 6UL SBC Express, version 2, ID 129
- Boot device: NAND
- Net: FEC0 [PRIME]
- Hit any key to stop autoboot: 0
- ## Resetting to default environment
- oldval: 00:04:F3:07:90:7C defval: 00:04:f3:ff:ff:fa
- ## Error: Can't overwrite "ethaddr"
- himport_r: can't insert "ethaddr=00:04:f3:ff:ff:fa" into hash table
- oldval: 00:04:F3:07:90:7E defval: 00:04:f3:ff:ff:fb
- ## Error: Can't overwrite "wlanaddr"
- himport_r: can't insert "wlanaddr=00:04:f3:ff:ff:fb" into hash table
- oldval: 00:04:F3:07:90:7F defval: 00:04:f3:ff:ff:fc
- ## Error: Can't overwrite "btaddr"
- himport_r: can't insert "btaddr=00:04:f3:ff:ff:fc" into hash table
- oldval: 00:04:F3:07:90:7D defval: 00:04:f3:ff:ff:fd
- ## Error: Can't overwrite "eth1addr"
- himport_r: can't insert "eth1addr=00:04:f3:ff:ff:fd" into hash table
- Saving Environment to NAND...
- Erasing NAND...
- Erasing at 0x300000 -- 100% complete.
- Writing to NAND... OK
- >> Installing Linux kernel and device tree files
- NAND erase.part: device 0 offset 0x500000, size 0xc00000
- Erasing at 0x10e0000 -- 100% complete.
- OK
- NAND erase.part: device 0 offset 0x500000, size 0xc00000
- Erasing at 0x10e0000 -- 100% complete.
- OK
- ubi0: attaching mtd1
- ubi0: scanning is finished
- ubi0: empty MTD device detected
- ubi0: attached mtd1 (name "mtd=3", size 12 MiB)
- ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
- ubi0: good PEBs: 96, bad PEBs: 0, corrupted PEBs: 0
- ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
- ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 0
- ubi0: available PEBs: 88, total reserved PEBs: 8, PEBs reserved for bad PEB handling: 4
- No size specified -> Using max size (11173888)
- Creating dynamic volume linux of size 11173888
- reading core-image-base-ccimx6ulstarter.boot.ubifs
- 7491584 bytes read in 334 ms (21.4 MiB/s)
- 7491584 bytes written to volume linux
- Verifying firmware...
- Volume linux found at volume id 0
- Comparing 7491584 bytes from volume 0, offset 0 with 80800000(buf address)
- Update was successful
- >> Installing recovery
- NAND erase.part: device 0 offset 0x1100000, size 0xe00000
- Erasing at 0x1ee0000 -- 100% complete.
- OK
- NAND erase.part: device 0 offset 0x1100000, size 0xe00000
- Erasing at 0x1ee0000 -- 100% complete.
- OK
- ubi0: detaching mtd1
- ubi0: mtd1 is detached
- ubi0: attaching mtd1
- ubi0: scanning is finished
- ubi0: empty MTD device detected
- ubi0: attached mtd1 (name "mtd=4", size 14 MiB)
- ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
- ubi0: good PEBs: 112, bad PEBs: 0, corrupted PEBs: 0
- ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
- ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 0
- ubi0: available PEBs: 103, total reserved PEBs: 9, PEBs reserved for bad PEB handling: 5
- No size specified -> Using max size (13078528)
- Creating dynamic volume recovery of size 13078528
- reading core-image-base-ccimx6ulstarter.recovery.ubifs
- 11173888 bytes read in 493 ms (21.6 MiB/s)
- 11173888 bytes written to volume recovery
- Verifying firmware...
- Volume recovery found at volume id 0
- Comparing 11173888 bytes from volume 0, offset 0 with 80800000(buf address)
- Update was successful
- >> Installing Linux root file system
- NAND erase.part: device 0 offset 0x1f00000, size 0x7a00000
- Erasing at 0x98e0000 -- 100% complete.
- OK
- NAND erase.part: device 0 offset 0x1f00000, size 0x7a00000
- Erasing at 0x98e0000 -- 100% complete.
- OK
- ubi0: detaching mtd1
- ubi0: mtd1 is detached
- ubi0: attaching mtd1
- ubi0: scanning is finished
- ubi0: empty MTD device detected
- ubi0: attached mtd1 (name "mtd=5", size 122 MiB)
- ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
- ubi0: good PEBs: 976, bad PEBs: 0, corrupted PEBs: 0
- ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
- ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 0
- ubi0: available PEBs: 932, total reserved PEBs: 44, PEBs reserved for bad PEB handling: 40
- No size specified -> Using max size (118341632)
- Creating dynamic volume rootfs of size 118341632
- reading core-image-base-ccimx6ulstarter.ubifs
- 74661888 bytes read in 3185 ms (22.4 MiB/s)
- 74661888 bytes written to volume rootfs
- Verifying firmware...
- Volume rootfs found at volume id 0
- Comparing 74661888 bytes from volume 0, offset 0 with 80800000(buf address)
- Update was successful
- Saving Environment to NAND...
- Erasing redundant NAND...
- Erasing at 0x320000 -- 100% complete.
- Writing to redundant NAND... OK
- >> Firmware installation complete. Rebooting into recovery mode for final deployment.
- resetting ...
- U-Boot dub-2017.03-r1.2+g8d60f53 (Nov 07 2018 - 14:18:11 +0000)
- CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
- CPU: Industrial temperature grade (-40C to 105C) at 39C
- Reset cause: POR
- I2C: ready
- DRAM: 256 MiB
- MCA: HW_VER=1 FW_VER=0.18
- PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
- NAND: 256 MiB
- MMC: FSL_SDHC: 0
- In: serial
- Out: serial
- Err: serial
- Model: Digi International ConnectCore 6UL Starter Board.
- ConnectCore 6UL SOM variant 0x02: Industrial Ultralite 528MHz, 256MB NAND, 256MB DDR3, -40/+85C, Wireless, Bluetooth
- Board: ConnectCore 6UL SBC Express, version 2, ID 129
- Boot device: NAND
- Net: FEC0 [PRIME]
- ******************************************
- * Warning: Booting into recovery mode... *
- ******************************************
- Hit any key to stop autoboot: 0
- ubi0: attaching mtd1
- ubi0: scanning is finished
- ubi0: attached mtd1 (name "mtd=4", size 14 MiB)
- ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
- ubi0: good PEBs: 112, bad PEBs: 0, corrupted PEBs: 0
- ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
- ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
- ubi0: available PEBs: 0, total reserved PEBs: 112, PEBs reserved for bad PEB handling: 5
- Loading file 'boot.scr' to addr 0x80800000...
- Done
- ## Executing script at 80800000
- Unmounting UBIFS volume recovery!
- ubi0: detaching mtd1
- ubi0: mtd1 is detached
- ubi0: attaching mtd1
- ubi0: scanning is finished
- ubi0: attached mtd1 (name "mtd=4", size 14 MiB)
- ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
- ubi0: good PEBs: 112, bad PEBs: 0, corrupted PEBs: 0
- ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
- ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
- ubi0: available PEBs: 0, total reserved PEBs: 112, PEBs reserved for bad PEB handling: 5
- Loading file 'zImage-ccimx6ulstarter.bin' to addr 0x80800000...
- Done
- Unmounting UBIFS volume recovery!
- ubi0: detaching mtd1
- ubi0: mtd1 is detached
- ubi0: attaching mtd1
- ubi0: scanning is finished
- ubi0: attached mtd1 (name "mtd=4", size 14 MiB)
- ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
- ubi0: good PEBs: 112, bad PEBs: 0, corrupted PEBs: 0
- ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
- ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
- ubi0: available PEBs: 0, total reserved PEBs: 112, PEBs reserved for bad PEB handling: 5
- Loading file 'zImage-imx6ul-ccimx6ulstarter-id129.dtb' to addr 0x83000000...
- Done
- Unmounting UBIFS volume recovery!
- ubi0: detaching mtd1
- ubi0: mtd1 is detached
- ubi0: attaching mtd1
- ubi0: scanning is finished
- ubi0: attached mtd1 (name "mtd=4", size 14 MiB)
- ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
- ubi0: good PEBs: 112, bad PEBs: 0, corrupted PEBs: 0
- ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
- ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
- ubi0: available PEBs: 0, total reserved PEBs: 112, PEBs reserved for bad PEB handling: 5
- Loading file 'uramdisk-recovery.img' to addr 0x83800000...
- Done
- Unmounting UBIFS volume recovery!
- Kernel image @ 0x80800000 [ 0x000000 - 0x597c38 ]
- ## Loading init Ramdisk from Legacy Image at 83800000 ...
- Image Name: dey-image-recovery-initramfs-cci
- Image Type: ARM Linux RAMDisk Image (uncompressed)
- Data Size: 3476254 Bytes = 3.3 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 83000000
- Booting using the fdt blob at 0x83000000
- Using Device Tree in place at 83000000, end 8300af12
- Modify /soc/aips-bus@02000000/bee@02044000:status disabled
- ft_system_setup for mx6
- switch to ldo_bypass mode!
- Starting kernel ...
- Booting Linux on physical CPU 0x0
- Linux version 4.9.81-dey+g4b330d1 (oe-user@oe-host) (gcc version 7.3.0 (GCC) ) #1 SMP PREEMPT Wed Nov 7 14:08:10 UTC 2018
- CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
- CPU: div instructions available: patching division code
- CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- OF: fdt:Machine model: Digi International ConnectCore 6UL Starter Board.
- Reserved memory: created CMA memory pool at 0x8c000000, size 64 MiB
- OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
- Memory policy: Data cache writealloc
- percpu: Embedded 14 pages/cpu @8bd72000 s25740 r8192 d23412 u57344
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64960
- Kernel command line: console=ttymxc4,115200 mtdparts=gpmi-nand:3m(bootloader),1m(environment),1m(safe),12m(linux),14m(recovery),122m(rootfs),-(update) ubi.mtd=3 ubi.mtd=5 root=ubi1_0 rootfstype=ubifs rw
- PID hash table entries: 1024 (order: 0, 4096 bytes)
- Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
- Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
- Memory: 177212K/262144K available (8192K kernel code, 397K rwdata, 2432K rodata, 1024K init, 446K bss, 19396K reserved, 65536K cma-reserved, 0K highmem)
- Virtual kernel memory layout:
- vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
- vmalloc : 0x90800000 - 0xff800000 (1776 MB)
- lowmem : 0x80000000 - 0x90000000 ( 256 MB)
- pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
- modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
- .text : 0x80008000 - 0x80900000 (9184 kB)
- .init : 0x80c00000 - 0x80d00000 (1024 kB)
- .data : 0x80d00000 - 0x80d63540 ( 398 kB)
- .bss : 0x80d65000 - 0x80dd4bd4 ( 447 kB)
- SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- Preemptible hierarchical RCU implementation.
- Build-time adjustment of leaf fanout to 32.
- RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
- RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1
- NR_IRQS:16 nr_irqs:16 16
- Switching to timer-based delay loop, resolution 333ns
- sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
- clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
- Console: colour dummy device 80x30
- Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- CPU: Testing write buffer coherency: ok
- CPU0: update cpu_capacity 1024
- CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
- Setting up static identity map for 0x80100000 - 0x80100058
- Brought up 1 CPUs
- SMP: Total of 1 processors activated (6.00 BogoMIPS).
- CPU: All CPU(s) started in SVC mode.
- devtmpfs: initialized
- VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
- clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- futex hash table entries: 256 (order: 2, 16384 bytes)
- pinctrl core: initialized pinctrl subsystem
- NET: Registered protocol family 16
- DMA: preallocated 256 KiB pool for atomic coherent allocations
- cpuidle: using governor menu
- cpu: bypassed regulator has no supply!
- cpu: failed to get the current voltage(-517)
- vddsoc: bypassed regulator has no supply!
- vddsoc: failed to get the current voltage(-517)
- hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
- hw-breakpoint: maximum watchpoint size is 8 bytes.
- imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
- mxs-dma 1804000.dma-apbh: initialized
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- i2c i2c-0: IMX I2C adapter registered
- i2c i2c-0: can't use DMA, using PIO instead.
- i2c i2c-1: IMX I2C adapter registered
- i2c i2c-1: can't use DMA, using PIO instead.
- Linux video capture interface: v2.00
- pps_core: LinuxPPS API ver. 1 registered
- pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- PTP clock support registered
- Advanced Linux Sound Architecture Driver Initialized.
- Bluetooth: Core ver 2.22
- NET: Registered protocol family 31
- Bluetooth: HCI device and connection manager initialized
- Bluetooth: HCI socket layer initialized
- Bluetooth: L2CAP socket layer initialized
- Bluetooth: SCO socket layer initialized
- clocksource: Switched to clocksource mxc_timer1
- NET: Registered protocol family 2
- TCP established hash table entries: 2048 (order: 1, 8192 bytes)
- TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
- TCP: Hash tables configured (established 2048 bind 2048)
- UDP hash table entries: 256 (order: 1, 8192 bytes)
- UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- NET: Registered protocol family 1
- RPC: Registered named UNIX socket transport module.
- RPC: Registered udp transport module.
- RPC: Registered tcp transport module.
- RPC: Registered tcp NFSv4.1 backchannel transport module.
- Trying to unpack rootfs image as initramfs...
- Freeing initrd memory: 3396K
- Bus freq driver module loaded
- workingset: timestamp_bits=14 max_order=16 bucket_order=2
- NFS: Registering the id_resolver key type
- Key type id_resolver registered
- Key type id_legacy registered
- io scheduler noop registered
- io scheduler deadline registered
- io scheduler cfq registered (default)
- imx-weim 21b8000.weim: Driver registered.
- pfuze100-regulator 0-0008: Full layer: 1, Metal layer: 1
- pfuze100-regulator 0-0008: FAB: 0, FIN: 0
- pfuze100-regulator 0-0008: pfuze3000 found.
- random: fast init done
- imx-sdma 20ec000.sdma: loaded firmware 3.3
- 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 21, base_baud = 5000000) is a IMX
- 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 57, base_baud = 5000000) is a IMX
- 21f4000.serial: ttymxc4 at MMIO 0x21f4000 (irq = 58, base_baud = 5000000) is a IMX
- console [ttymxc4] enabled
- brd: module loaded
- loop: module loaded
- caam 2140000.caam: ERA source: CCBVID.
- caam 2140000.caam: Deinstantiated RNG4 SH0
- caam 2140000.caam: Entropy delay = 3200
- caam 2140000.caam: Instantiated RNG4 SH0
- caam 2140000.caam: Instantiated RNG4 SH1
- caam 2140000.caam: device ID = 0x0a16030000000000 (Era 8)
- caam 2140000.caam: job rings = 3, qi = 0
- caam algorithms registered in /proc/crypto
- caam_jr 2141000.jr0: registering rng-caam
- random: crng init done
- caam 2140000.caam: caam pkc algorithms registered in /proc/crypto
- snvs-secvio 20cc000.caam-snvs: can't get snvs clock
- snvs-secvio 20cc000.caam-snvs: violation handlers armed - non-secure state
- caam_keyblob caam-keyblob: caam keyblob initialized
- nand: device found, Manufacturer ID: 0x01, Chip ID: 0xda
- nand: AMD/Spansion S34ML02G2
- nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
- gpmi-nand 1806000.gpmi-nand: enable the asynchronous EDO mode 4
- Scanning device for bad blocks
- 7 cmdlinepart partitions found on MTD device gpmi-nand
- Creating 7 MTD partitions on "gpmi-nand":
- 0x000000000000-0x000000300000 : "bootloader"
- 0x000000300000-0x000000400000 : "environment"
- 0x000000400000-0x000000500000 : "safe"
- 0x000000500000-0x000001100000 : "linux"
- 0x000001100000-0x000001f00000 : "recovery"
- 0x000001f00000-0x000009900000 : "rootfs"
- 0x000009900000-0x000010000000 : "update"
- gpmi-nand 1806000.gpmi-nand: driver registered.
- spi_imx 2010000.ecspi: probed
- libphy: Fixed MDIO Bus: probed
- CAN device driver interface
- flexcan 2090000.flexcan: device registered (reg_base=9099c000, irq=24)
- 2188000.ethernet supply phy not found, using dummy regulator
- pps pps0: new PPS source ptp0
- libphy: fec_enet_mii_bus: probed
- fec 2188000.ethernet eth0: registered PHC device 0
- PPP generic driver version 2.4.2
- PPP BSD Compression module registered
- PPP Deflate Compression module registered
- usbcore: registered new interface driver cdc_ether
- usbcore: registered new interface driver cdc_eem
- usbcore: registered new interface driver sierra_net
- usbcore: registered new interface driver cdc_ncm
- usbcore: registered new interface driver qmi_wwan
- usbcore: registered new interface driver cdc_mbim
- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- ehci-mxc: Freescale On-Chip EHCI Host driver
- usbcore: registered new interface driver cdc_acm
- cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
- usbcore: registered new interface driver cdc_wdm
- usbcore: registered new interface driver usb-storage
- usbcore: registered new interface driver usbserial
- usbcore: registered new interface driver usbserial_generic
- usbserial: USB Serial support registered for generic
- usbcore: registered new interface driver option
- usbserial: USB Serial support registered for GSM modem (1-port)
- usbcore: registered new interface driver qcserial
- usbserial: USB Serial support registered for Qualcomm USB modem
- usbcore: registered new interface driver sierra
- usbserial: USB Serial support registered for Sierra USB modem
- usbcore: registered new interface driver usb_ehset_test
- 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
- 2184000.usb supply vbus not found, using dummy regulator
- ci_hdrc ci_hdrc.0: EHCI Host Controller
- ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
- ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- 2184200.usb supply vbus not found, using dummy regulator
- ci_hdrc ci_hdrc.1: EHCI Host Controller
- ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
- ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 1 port detected
- mousedev: PS/2 mouse device common for all mice
- input: mca-cc6ul-pwrkey as /devices/soc0/soc/2100000.aips-bus/21a0000.i2c/i2c-0/0-007e/mca-cc6ul-pwrkey/input/input0
- mca-cc6ul-rtc mca-cc6ul-rtc: rtc core: registered mca-cc6ul-rtc as rtc0
- i2c /dev entries driver
- Watchdog driver for MCA of CC6UL (timeout=30 sec, nowayout=1, reset (full))
- Bluetooth: HCI UART driver ver 2.3
- Bluetooth: HCI UART protocol H4 registered
- Bluetooth: HCI UART protocol ATH3K registered
- Bluetooth: HCI UART protocol (null) registered
- Bluetooth: HCI_IBS protocol initialized
- sdhci: Secure Digital Host Controller Interface driver
- sdhci: Copyright(c) Pierre Ossman
- sdhci-pltfm: SDHCI platform and OF driver helper
- mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
- mmc0: queuing unknown CIS tuple 0x01 (3 bytes)
- mmc0: queuing unknown CIS tuple 0x1a (5 bytes)
- mmc0: queuing unknown CIS tuple 0x1b (8 bytes)
- mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
- usbcore: registered new interface driver usbhid
- usbhid: USB HID core driver
- mmc0: queuing unknown CIS tuple 0x14 (0 bytes)
- ADC driver for MCA
- Tamper driver for MCA of CC6UL
- mmc0: queuing unknown CIS tuple 0x80 (1 bytes)
- mmc0: queuing unknown CIS tuple 0x81 (1 bytes)
- mmc0: queuing unknown CIS tuple 0x82 (1 bytes)
- mmc0: new high speed SDIO card at address 0001
- NET: Registered protocol family 26
- NET: Registered protocol family 10
- sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
- NET: Registered protocol family 17
- can: controller area network core (rev 20120528 abi 9)
- NET: Registered protocol family 29
- can: raw protocol (rev 20120528)
- can: broadcast manager protocol (rev 20161123 t)
- can: netlink gateway (rev 20130117) max_hops=1
- Bluetooth: RFCOMM TTY layer initialized
- Bluetooth: RFCOMM socket layer initialized
- Bluetooth: RFCOMM ver 1.11
- Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- Bluetooth: BNEP filters: protocol multicast
- Bluetooth: BNEP socket layer initialized
- Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- Bluetooth: HIDP socket layer initialized
- 8021q: 802.1Q VLAN Support v1.8
- lib80211: common routines for IEEE802.11 drivers
- Key type dns_resolver registered
- Failed to disable 696MHz OPP
- cpu cpu0: regulators not ready, retry
- mmc1: host does not support reading read-only switch, assuming write-enable
- mmc1: new high speed SDHC card at address 59b4
- mmcblk1: mmc1:59b4 USD 14.9 GiB
- mmcblk1: p1
- cpu: supplied by SW1B
- vddsoc: supplied by SW1B
- cpu cpu0: Registered imx6q-cpufreq
- imx_thermal 2000000.aips-bus:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:85C
- i.MX junction temperature 40 celsius.ubi0: default fastmap pool size: 8
- ubi0: default fastmap WL pool size: 4
- ubi0: attaching mtd3
- ubi0: scanning is finished
- ubi0 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 2, need 40
- ubi0: attached mtd3 (name "linux", size 12 MiB)
- ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
- ubi0: good PEBs: 96, bad PEBs: 0, corrupted PEBs: 0
- ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
- ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
- ubi0: available PEBs: 0, total reserved PEBs: 96, PEBs reserved for bad PEB handling: 2
- ubi0: background thread "ubi_bgt0d" started, PID 174
- ubi1: default fastmap pool size: 45
- ubi1: default fastmap WL pool size: 22
- ubi1: attaching mtd5
- ubi1: scanning is finished
- ubi1 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 38, need 40
- ubi1: attached mtd5 (name "rootfs", size 122 MiB)
- ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
- ubi1: good PEBs: 976, bad PEBs: 0, corrupted PEBs: 0
- ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
- ubi1: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
- ubi1: available PEBs: 0, total reserved PEBs: 976, PEBs reserved for bad PEB handling: 38
- ubi1: background thread "ubi_bgt1d" started, PID 175
- mca-cc6ul-rtc mca-cc6ul-rtc: setting system clock to 2018-11-07 14:50:58 UTC (1541602258)
- VLDO3: disabling
- VLDO4: disabling
- ALSA device list:
- No soundcards found.
- Freeing unused kernel memory: 1024K
- ubi2: default fastmap pool size: 40
- ubi2: default fastmap WL pool size: 20
- ubi2: attaching mtd6
- ubi2: scanning is finished
- ubi2: attached mtd6 (name "update", size 103 MiB)
- ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
- ubi2: good PEBs: 824, bad PEBs: 0, corrupted PEBs: 0
- ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
- ubi2: max/mean erase counter: 9/4, WL threshold: 4096, image sequence number: 162681444
- ubi2: available PEBs: 0, total reserved PEBs: 824, PEBs reserved for bad PEB handling: 40
- ubi2: background thread "ubi_bgt2d" started, PID 191
- UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 197
- UBIFS (ubi2:0): recovery needed
- UBIFS (ubi2:0): recovery completed
- UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "update"
- UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
- UBIFS (ubi2:0): FS size: 97390592 bytes (92 MiB, 767 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
- UBIFS (ubi2:0): reserved for root: 0 bytes (0 KiB)
- UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID 5283539C-D788-4DA6-9300-2ED10A0CC129, small LPT model
- Error opening /dev/fb0
- [RECOVERY] Starting recovery...
- Warning: Bad CRC, using default environment
- MTD erase error on /dev/mtd1: Invalid argument
- Error: can't write fw_env to flash
- Warning: Bad CRC, using default environment
- MTD erase error on /dev/mtd1: Invalid argument
- Error: can't write fw_env to flash
- [RECOVERY] [ERROR] No command found
- [RECOVERY] The system will now reboot in 10 seconds
- reboot: Restarting system
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement