View difference between Paste ID: <a href="/zZp2Ezns">zZp2Ezns</a> and <a href="/MsNNYVeu">MsNNYVeu</a>

# generated by Slic3r 1.1.1-dev on Mon Apr 21 17:03:15 2014
1	-	# generated by Slic3r 1.1.1-dev on Mon Apr 21 17:03:15 2014
1	+	# generated by Slic3r 1.1.1-dev on Mon Apr 21 17:06:40 2014
2	-
2	+
3	-	[filament:- default -]
3	+
4	-	bed_temperature = 0
4	+
5		bottom_solid_layers = 2
6	-	cooling = 0
6	+
7		bridge_fan_speed = 100
8		bridge_flow_ratio = 0.99
9		bridge_speed = 40
10	-	fan_below_layer_time = 60
10	+
11	-	filament_diameter = 3
11	+
12	-	first_layer_bed_temperature = 0
12	+
13	-	first_layer_temperature = 190
13	+
14		disable_fan_first_layers = 1
15		duplicate_distance = 6
16	-	min_print_speed = 10
16	+
17	-	slowdown_below_layer_time = 15
17	+
18	-	temperature = 185
18	+
19	-
19	+
20	-	[filament:FD Arctic white]
20	+
21		extruder_clearance_radius = 50
22		extruder_offset = 0x0
23		extrusion_axis = E
24		extrusion_multiplier = 1
25		extrusion_width = 0
26		fan_always_on = 0
27		fan_below_layer_time = 90
28		filament_diameter = 2.85
29		fill_angle = 45
30		fill_density = 25%
31		fill_pattern = rectilinear
32		first_layer_acceleration = 0
33		first_layer_bed_temperature = 58
34		first_layer_extrusion_width = 0
35		first_layer_height = 100%
36	-
36	+
37	-	[filament:FD Beige]
37	+
38	-	bed_temperature = 57
38	+	g0 = 0
39		gap_fill_speed = 20
40		gcode_arcs = 0
41		gcode_comments = 0
42		gcode_flavor = reprap
43		infill_acceleration = 0
44		infill_every_layers = 1
45		infill_extruder = 1
46		infill_extrusion_width = 0
47		infill_first = 0
48		infill_only_where_needed = 0
49		infill_speed = 35
50		interface_shells = 0
51		layer_gcode =
52		layer_height = 0.254
53	-
53	+
54	-	[filament:FF Black]
54	+
55	-	bed_temperature = 115
55	+
56		min_skirt_length = 0
57	-	cooling = 0
57	+
58	-	disable_fan_first_layers = 3
58	+
59		only_retract_when_crossing_perimeters = 0
60	-	fan_always_on = 1
60	+
61		output_filename_format = [input_filename_base].gcode
62	-	filament_diameter = 2.95
62	+
63	-	first_layer_bed_temperature = 125
63	+
64	-	first_layer_temperature = 220
64	+
65		perimeter_extrusion_width = 0
66	-	min_fan_speed = 25
66	+
67		perimeters = 2
68		post_process =
69	-	temperature = 215
69	+
70	-
70	+
71	-	[filament:My Settings]
71	+
72	-	bed_temperature = 120
72	+
73		retract_before_travel = 1
74	-	cooling = 0
74	+
75	-	disable_fan_first_layers = 3
75	+
76		retract_length_toolchange = 3
77	-	fan_always_on = 1
77	+
78		retract_restart_extra = 0
79	-	filament_diameter = 3
79	+
80	-	first_layer_bed_temperature = 125
80	+
81	-	first_layer_temperature = 205
81	+
82		skirt_height = 2
83	-	min_fan_speed = 25
83	+
84		slowdown_below_layer_time = 30
85		small_perimeter_speed = 25
86	-	temperature = 200
86	+
87	-
87	+
88	-	[filament:slic3r]
88	+
89	-	bed_temperature = 58
89	+
90		solid_infill_speed = 35
91		spiral_vase = 0
92		standby_temperature_delta = -5
93		start_gcode = G28 ; home all axes\nG92 E0; extruder reset\nG1 E5; Make a blob to catch strays\nG1 F1500\nG1 Y0 E20 F3000; Move Y to center and prime/wipe nozzle.\nG92 E0; extruder reset
94		start_perimeters_at_concave_points = 0
95	-	fan_below_layer_time = 80
95	+
96	-	filament_diameter = 2.95
96	+
97	-	first_layer_bed_temperature = 65
97	+
98		support_material_enforce_layers = 0
99		support_material_extruder = 1
100	-	min_fan_speed = 15
100	+
101		support_material_interface_extruder = 1
102	-	slowdown_below_layer_time = 15
102	+
103		support_material_interface_spacing = 0
104	-
104	+
105	-	[filament:slic3r_thin_wall]
105	+
106	-	bed_temperature = 58
106	+
107		support_material_threshold = 45
108		temperature = 180
109	-	disable_fan_first_layers = 3
109	+
110		threads = 4
111		toolchange_gcode =
112	-	fan_below_layer_time = 80
112	+
113	-	filament_diameter = 3.2
113	+
114	-	first_layer_bed_temperature = 65
114	+
115		travel_speed = 50
116	-	max_fan_speed = 69
116	+
117	-	min_fan_speed = 15
117	+
118	-	min_print_speed = 1
118	+
119	-	slowdown_below_layer_time = 15
119	+
120		z_offset = 0