AnWe_Slic3r_config_bundle.ini

# generated by Slic3r 1.1.1-dev on Mon Apr 21 17:03:15 2014

[filament:- default -]
bed_temperature = 0
bridge_fan_speed = 100
cooling = 0
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 3
first_layer_bed_temperature = 0
first_layer_temperature = 190
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 15
temperature = 185

[filament:FD Arctic white]
bed_temperature = 55
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 90
filament_diameter = 2.85
first_layer_bed_temperature = 58
first_layer_temperature = 185
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
slowdown_below_layer_time = 30
temperature = 180

[filament:FD Beige]
bed_temperature = 57
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 90
filament_diameter = 2.85
first_layer_bed_temperature = 58
first_layer_temperature = 185
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
slowdown_below_layer_time = 30
temperature = 180

[filament:FF Black]
bed_temperature = 115
bridge_fan_speed = 100
cooling = 0
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 90
filament_diameter = 2.95
first_layer_bed_temperature = 125
first_layer_temperature = 220
max_fan_speed = 100
min_fan_speed = 25
min_print_speed = 5
slowdown_below_layer_time = 30
temperature = 215

[filament:My Settings]
bed_temperature = 120
bridge_fan_speed = 100
cooling = 0
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 90
filament_diameter = 3
first_layer_bed_temperature = 125
first_layer_temperature = 205
max_fan_speed = 100
min_fan_speed = 25
min_print_speed = 5
slowdown_below_layer_time = 30
temperature = 200

[filament:slic3r]
bed_temperature = 58
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 80
filament_diameter = 2.95
first_layer_bed_temperature = 65
first_layer_temperature = 185
max_fan_speed = 100
min_fan_speed = 15
min_print_speed = 5
slowdown_below_layer_time = 15
temperature = 180

[filament:slic3r_thin_wall]
bed_temperature = 58
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 80
filament_diameter = 3.2
first_layer_bed_temperature = 65
first_layer_temperature = 185
max_fan_speed = 69
min_fan_speed = 15
min_print_speed = 1
slowdown_below_layer_time = 15
temperature = 180

[filament:slic3r_thin_wall_honeycomb]
bed_temperature = 58
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 80
filament_diameter = 3
first_layer_bed_temperature = 65
first_layer_temperature = 185
max_fan_speed = 100
min_fan_speed = 15
min_print_speed = 5
slowdown_below_layer_time = 15
temperature = 180

[presets]
filament = FD Arctic white.ini
print = rect_sparse.ini
printer = MendelMax.ini

[print:- default -]
bottom_solid_layers = 3
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
external_perimeter_speed = 100%
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 40%
fill_pattern = rectilinear
first_layer_extrusion_width = 200%
first_layer_height = 0.4572
first_layer_speed = 30%
gcode_comments = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_speed = 60
layer_height = 0.3572
notes =
output_filename_format = [input_filename_base].gcode
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process =
randomize_start = 1
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_speed = 60
support_material = 0
support_material_angle = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_threshold = 45
threads = 2
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130

[print:My Settings]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 0
bridge_speed = 40
brim_width = 0
complete_objects = 0
default_acceleration = 0
external_perimeter_speed = 80%
external_perimeters_first = 1
extra_perimeters = 0
extruder_clearance_height = 40
extruder_clearance_radius = 50
extrusion_width = 0
fill_angle = 45
fill_density = 0%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.5
first_layer_speed = 75%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 35
layer_height = 0.4
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 1
post_process =
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 3
skirt_height = 5
skirts = 2
small_perimeter_speed = 25
solid_fill_pattern = rectilinear
solid_infill_below_area = 35
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 35
spiral_vase = 0
standby_temperature_delta = -5
start_perimeters_at_concave_points = 1
start_perimeters_at_non_overhang = 1
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 40
support_material_threshold = 45
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 25
top_solid_layers = 4
travel_speed = 50

[print:Vase]
avoid_crossing_perimeters = 1
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 40
brim_width = 1
complete_objects = 1
default_acceleration = 0
external_perimeter_speed = 80%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 60
extruder_clearance_radius = 40
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 35
layer_height = 0.254
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 1
post_process =
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 3
skirt_height = 1
skirts = 2
small_perimeter_speed = 25
solid_fill_pattern = rectilinear
solid_infill_below_area = 2
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 35
spiral_vase = 1
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 45
threads = 3
top_infill_extrusion_width = 0
top_solid_infill_speed = 25
top_solid_layers = 2
travel_speed = 60

[print:calibration]
avoid_crossing_perimeters = 0
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 0.99
bridge_speed = 40
brim_width = 0
complete_objects = 1
default_acceleration = 0
external_perimeter_speed = 80%
external_perimeters_first = 1
extra_perimeters = 1
extruder_clearance_height = 40
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 95%
fill_pattern = rectilinear
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 75%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 35
layer_height = 0.254
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 1
post_process =
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 3
skirt_height = 1
skirts = 2
small_perimeter_speed = 25
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 35
spiral_vase = 0
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 45
threads = 3
top_infill_extrusion_width = 0
top_solid_infill_speed = 25
top_solid_layers = 2
travel_speed = 60

[print:honeycomb]
avoid_crossing_perimeters = 0
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 40
brim_width = 0
complete_objects = 1
default_acceleration = 0
external_perimeter_speed = 80%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 60
extruder_clearance_radius = 40
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = honeycomb
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 50%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 35
layer_height = 0.254
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 1
post_process =
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 3
skirt_height = 1
skirts = 2
small_perimeter_speed = 25
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 35
spiral_vase = 0
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 45
threads = 3
top_infill_extrusion_width = 0
top_solid_infill_speed = 25
top_solid_layers = 2
travel_speed = 60

[print:one_go_rect_m]
avoid_crossing_perimeters = 0
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 0.99
bridge_speed = 40
brim_width = 0
complete_objects = 0
default_acceleration = 0
external_perimeter_speed = 80%
external_perimeters_first = 1
extra_perimeters = 1
extruder_clearance_height = 40
extruder_clearance_radius = 50
extrusion_width = 0
fill_angle = 45
fill_density = 40%
fill_pattern = rectilinear
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 75%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 35
layer_height = 0.254
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 2
post_process =
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 3
skirt_height = 1
skirts = 2
small_perimeter_speed = 25
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 35
spiral_vase = 0
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 45
threads = 3
top_infill_extrusion_width = 0
top_solid_infill_speed = 25
top_solid_layers = 2
travel_speed = 60

[print:rect_sparse]
avoid_crossing_perimeters = 0
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 0.99
bridge_speed = 40
brim_width = 0
complete_objects = 0
default_acceleration = 0
external_perimeter_speed = 80%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 40
extruder_clearance_radius = 50
extrusion_width = 0
fill_angle = 45
fill_density = 25%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 75%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 35
interface_shells = 0
layer_height = 0.254
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 2
post_process =
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 3
skirt_height = 2
skirts = 2
small_perimeter_speed = 25
solid_fill_pattern = rectilinear
solid_infill_below_area = 35
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 35
spiral_vase = 0
standby_temperature_delta = -5
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 1
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 45
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 25
top_solid_layers = 2
travel_speed = 50

[print:rect_sturdy]
avoid_crossing_perimeters = 0
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 0.99
bridge_speed = 40
brim_width = 0
complete_objects = 0
default_acceleration = 0
external_perimeter_speed = 80%
external_perimeters_first = 1
extra_perimeters = 1
extruder_clearance_height = 40
extruder_clearance_radius = 50
extrusion_width = 0
fill_angle = 45
fill_density = 75%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 75%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 35
layer_height = 0.254
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 1
post_process =
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 3
skirt_height = 2
skirts = 2
small_perimeter_speed = 25
solid_fill_pattern = rectilinear
solid_infill_below_area = 35
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 35
spiral_vase = 0
standby_temperature_delta = -5
start_perimeters_at_concave_points = 1
start_perimeters_at_non_overhang = 1
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 45
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 25
top_solid_layers = 2
travel_speed = 50

[print:rect_sturdy_support]
avoid_crossing_perimeters = 0
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 0.99
bridge_speed = 40
brim_width = 0
complete_objects = 0
default_acceleration = 0
external_perimeter_speed = 80%
external_perimeters_first = 1
extra_perimeters = 1
extruder_clearance_height = 40
extruder_clearance_radius = 50
extrusion_width = 0
fill_angle = 45
fill_density = 50%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 75%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 35
layer_height = 0.254
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 2
post_process =
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 3
skirt_height = 5
skirts = 2
small_perimeter_speed = 25
solid_fill_pattern = rectilinear
solid_infill_below_area = 5
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 35
spiral_vase = 0
standby_temperature_delta = -5
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 1
support_material = 1
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 45
thin_walls = 1
threads = 1
top_infill_extrusion_width = 0
top_solid_infill_speed = 25
top_solid_layers = 2
travel_speed = 60

[print:rectilinear medium]
avoid_crossing_perimeters = 0
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 0.99
bridge_speed = 40
brim_width = 0
complete_objects = 1
default_acceleration = 0
external_perimeter_speed = 80%
external_perimeters_first = 1
extra_perimeters = 1
extruder_clearance_height = 40
extruder_clearance_radius = 50
extrusion_width = 0
fill_angle = 45
fill_density = 40%
fill_pattern = rectilinear
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 75%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 35
layer_height = 0.254
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 2
post_process =
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 3
skirt_height = 1
skirts = 2
small_perimeter_speed = 25
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 35
spiral_vase = 0
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 45
threads = 3
top_infill_extrusion_width = 0
top_solid_infill_speed = 25
top_solid_layers = 2
travel_speed = 60

[print:rectilinear sparse]
avoid_crossing_perimeters = 0
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 0.99
bridge_speed = 40
brim_width = 0
complete_objects = 1
default_acceleration = 0
external_perimeter_speed = 80%
external_perimeters_first = 1
extra_perimeters = 1
extruder_clearance_height = 40
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 75%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 35
layer_height = 0.254
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 1
post_process =
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 3
skirt_height = 1
skirts = 2
small_perimeter_speed = 25
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 35
spiral_vase = 0
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 45
threads = 3
top_infill_extrusion_width = 0
top_solid_infill_speed = 25
top_solid_layers = 2
travel_speed = 60

[print:slic3r]
avoid_crossing_perimeters = 1
bottom_solid_layers = 1
bridge_flow_ratio = 0.95
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
external_perimeter_speed = 80%
extra_perimeters = 1
extruder_clearance_height = 40
extruder_clearance_radius = 25
extrusion_width = 0
fill_angle = 45
fill_density = 100%
fill_pattern = rectilinear
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_speed = 40
layer_height = 0.254
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 40
perimeters = 1
post_process =
raft_layers = 0
randomize_start = 1
skirt_distance = 5
skirt_height = 1
skirts = 3
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_speed = 40
support_material = 0
support_material_angle = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 45
threads = 5
top_solid_infill_speed = 30
top_solid_layers = 1
travel_speed = 130

[print:slic3r_thin_wall]
avoid_crossing_perimeters = 1
bottom_solid_layers = 1
bridge_flow_ratio = 1
bridge_speed = 40
brim_width = 0
complete_objects = 0
default_acceleration = 0
external_perimeter_speed = 80%
extra_perimeters = 1
extruder_clearance_height = 40
extruder_clearance_radius = 25
extrusion_width = 0.5
fill_angle = 45
fill_density = 100%
fill_pattern = rectilinear
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_speed = 35
layer_height = 0.254
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 1
post_process =
raft_layers = 0
randomize_start = 0
skirt_distance = 8
skirt_height = 1
skirts = 3
small_perimeter_speed = 25
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_speed = 35
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 45
threads = 5
top_solid_infill_speed = 25
top_solid_layers = 1
travel_speed = 100

[print:slic3r_thin_wall_honeycomb]
bottom_solid_layers = 1
bridge_flow_ratio = 0.95
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
external_perimeter_speed = 80%
extra_perimeters = 0
extruder_clearance_height = 40
extruder_clearance_radius = 25
extrusion_width = 0.5
fill_angle = 45
fill_density = 80%
fill_pattern = honeycomb
first_layer_extrusion_width = 0.4
first_layer_height = 100%
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_speed = 40
layer_height = 0.254
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 40
perimeters = 1
post_process =
randomize_start = 1
skirt_distance = 5
skirt_height = 1
skirts = 3
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_speed = 40
support_material = 0
support_material_angle = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 45
threads = 2
top_solid_infill_speed = 30
top_solid_layers = 1
travel_speed = 130

[print:slic3r_thin_wall_honeycomb_127]
bottom_solid_layers = 1
bridge_flow_ratio = 0.95
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
external_perimeter_speed = 80%
extra_perimeters = 0
extruder_clearance_height = 40
extruder_clearance_radius = 25
extrusion_width = 0.5
fill_angle = 45
fill_density = 50%
fill_pattern = honeycomb
first_layer_extrusion_width = 0.4
first_layer_height = 100%
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_speed = 40
layer_height = 0.127
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 1
post_process =
randomize_start = 1
skirt_distance = 5
skirt_height = 1
skirts = 3
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_speed = 40
support_material = 0
support_material_angle = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 45
threads = 2
top_solid_infill_speed = 30
top_solid_layers = 1
travel_speed = 130

[print:thinwall]
avoid_crossing_perimeters = 0
bottom_solid_layers = 1
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 40
brim_width = 0
complete_objects = 1
default_acceleration = 0
external_perimeter_speed = 80%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 60
extruder_clearance_radius = 40
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 50%
gap_fill_speed = 35
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 55
layer_height = 0.254
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 1
post_process =
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 3
skirt_height = 1
skirts = 2
small_perimeter_speed = 35
solid_fill_pattern = rectilinear
solid_infill_below_area = 2
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
start_perimeters_at_concave_points = 1
start_perimeters_at_non_overhang = 0
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 45
thin_walls = 1
threads = 1
top_infill_extrusion_width = 0
top_solid_infill_speed = 35
top_solid_layers = 1
travel_speed = 75

[printer:- default -]
bed_size = 228,246
end_gcode = M104 S0 ; turn off temperature\nG1 Z20 ; clear extruder\nG28 X0 Y0 ; home X and Y axis\nM84     ; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.4572
print_center = 0,0
retract_before_travel = 2
retract_length = 1
retract_lift = 0
retract_restart_extra = 0
retract_speed = 30
start_gcode = g1 Z20 ; clear clamps\nG28 ; home all axes\nG1 Y0 ; clear corner
use_relative_e_distances = 0
z_offset = 0

[printer:MendelMax]
bed_size = 205,270
end_gcode = G91; relative positioning\nG1 E-0.9; Retract \nG1 Z10 ; lift to clear print.\nG90; Back to absolute\nM104 S0 ; Extruder off\nM106 S256; fan full blast\nM190 S0; Cool bed to release print\nG4 S60; Pause\nM107; Fan off\nG28 Y0; home Y axis to "present" print\nM84; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.5
print_center = 0,0
retract_before_travel = 1
retract_layer_change = 1
retract_length = 1.6
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = G28 ; home all axes\nG92 E0; extruder reset\nG1 E5; Make a blob to catch strays\nG1 F1500\nG1 Y0 E20 F3000; Move Y to center and prime/wipe nozzle.\nG92 E0; extruder reset
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 10
wipe = 0
z_offset = 0

[printer:MendelMax_extended_X]
bed_size = 230,270
end_gcode = G91; relative positioning\nG1 E-0.9; Retract \nG1 Z10 ; lift to clear print.\nG90; Back to absolute\nM104 S0 ; Extruder off\nM106 S256; fan full blast\nM190 S0; Cool bed to release print\nG4 S60; Pause\nM107; Fan off\nG28 Y0; home Y axis to "present" print\nM84; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.5
print_center = 15,0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1.5
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 25
start_gcode = G28 ; home all axes\nG92 E0; extruder reset\nG1 E5; Make a blob to catch strays\nG1 Y0 E10; Move Y to center and prime/wipe nozzle.\nG92 E0; extruder reset
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 10
wipe = 0
z_offset = 0

[printer:My Settings]
bed_size = 210,270
end_gcode = G91; relative positioning\nG1 E-0.9; Retract \nG1 Z10 ; lift to clear print.\nG90; Back to absolute\nM104 S0 ; Extruder off\nM106 S256; fan full blast\nM190 S0; Cool bed to release print\nG4 S60; Pause\nM107; Fan off\nG28 Y0; home Y axis to "present" print\nM84; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.5
print_center = 105,135
retract_before_travel = 2
retract_layer_change = 1
retract_length = 0
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 25
start_gcode = G28 ; home all axes\nG92 E0; extruder reset\nG1 E5; Make a blob to catch strays\nG1 Y0 E10; Move Y to center and prime/wipe nozzle.\nG92 E0; extruder reset
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 10
wipe = 0
z_offset = 0

[printer:slic3r]
bed_size = 200,280
end_gcode = G91; relative positioning\nG1 Z10 E-1.25; Retract and lift to clear print.\nG90; Back to absolute\nM104 S0 ; Extruder off\nM106 S255; fan full blast\nM190 S40; Cool bed to release print\nM107; Fan off\nG28 Y0; home Y axis to "present" print\nM84; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.5
print_center = 0,0
retract_before_travel = 2
retract_length = 1.25
retract_length_toolchange = 3
retract_lift = 1.27
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = G28 ; home all axes\nG1 Z0.254 ; lift Z a little to mind for homeing offset\nG92 E0 ;zero extruder\nG1 Y0 E1.25 ; Move Y to center and prime/wipe nozzle.
toolchange_gcode =
use_relative_e_distances = 0
vibration_limit = 0
z_offset = 0.381

[printer:slic3r_thin_wall]
bed_size = 210,280
end_gcode = G91; relative positioning\nG1 E-1.25; Retract \nG1 Z10 ; lift to clear print.\nG90; Back to absolute\nM104 S0 ; Extruder off\nM106 S255; fan full blast\nM190 S0; Cool bed to release print\nM107; Fan off\nG28 Y0; home Y axis to "present" print\nM84; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.5
print_center = 0,0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 0.9
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 25
start_gcode = G28 ; home all axes\nG1 Z0.254 F5000; lift Z a little to mind for homeing offset\nG92 E0 ;zero extruder\nG1 Y0 E1.25 ; Move Y to center and prime/wipe nozzle.
toolchange_gcode =
use_relative_e_distances = 0
vibration_limit = 20
wipe = 1
z_offset = 0

[printer:slic3r_thin_wall_honeycomb]
bed_size = 200,280
end_gcode = G91; relative positioning\nG1 Z10 E-1.25; Retract and lift to clear print.\nG90; Back to absolute\nM104 S0 ; Extruder off\nM106 S255; fan full blast\nM190 S40; Cool bed to release print\nM107; Fan off\nG28 Y0; home Y axis to "present" print\nM84; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.5
print_center = 0,0
retract_before_travel = 2
retract_length = 1.3
retract_length_toolchange = 3
retract_lift = 1.27
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = G28 ; home all axes\nG1 Z0.254 ; lift Z a little to mind for homeing offset\nG92 E0 ;zero extruder\nG1 Y0 E1.25 ; Move Y to center and prime/wipe nozzle.
toolchange_gcode =
use_relative_e_distances = 0
vibration_limit = 0
z_offset = 0.508

[printer:slic3r_thin_wall_honeycomb_127]
bed_size = 200,280
end_gcode = G91; relative positioning\nG1 Z10 E-1.25; Retract and lift to clear print.\nG90; Back to absolute\nM104 S0 ; Extruder off\nM106 S255; fan full blast\nM190 S40; Cool bed to release print\nM107; Fan off\nG28 Y0; home Y axis to "present" print\nM84; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.5
print_center = 0,0
retract_before_travel = 2
retract_length = 1.3
retract_length_toolchange = 3
retract_lift = 1
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = G28 ; home all axes\nG1 Z0.254 ; lift Z a little to mind for homeing offset\nG92 E0 ;zero extruder\nG1 Y0 E1.25 ; Move Y to center and prime/wipe nozzle.
toolchange_gcode =
use_relative_e_distances = 0
vibration_limit = 0
z_offset = 0

[settings]
autocenter = 1
mode = expert