AnWe_Slic3r_config.ini

# generated by Slic3r 1.1.1-dev on Mon Apr 21 17:06:40 2014
avoid_crossing_perimeters = 0
bed_size = 205,270
bed_temperature = 55
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 0.99
bridge_speed = 40
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
duplicate_distance = 6
end_gcode = G91; relative positioning\nG1 E-0.9; Retract \nG1 Z10 ; lift to clear print.\nG90; Back to absolute\nM104 S0 ; Extruder off\nM106 S256; fan full blast\nM190 S0; Cool bed to release print\nG4 S60; Pause\nM107; Fan off\nG28 Y0; home Y axis to "present" print\nM84; disable motors
external_perimeter_speed = 80%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 40
extruder_clearance_radius = 50
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 90
filament_diameter = 2.85
fill_angle = 45
fill_density = 25%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_bed_temperature = 58
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 75%
first_layer_temperature = 185
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 35
interface_shells = 0
layer_gcode =
layer_height = 0.254
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
min_skirt_length = 0
notes =
nozzle_diameter = 0.5
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 2
post_process =
print_center = 0,0
raft_layers = 0
randomize_start = 0
resolution = 0
retract_before_travel = 1
retract_layer_change = 1
retract_length = 1.6
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
skirt_distance = 3
skirt_height = 2
skirts = 2
slowdown_below_layer_time = 30
small_perimeter_speed = 25
solid_fill_pattern = rectilinear
solid_infill_below_area = 35
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 35
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; home all axes\nG92 E0; extruder reset\nG1 E5; Make a blob to catch strays\nG1 F1500\nG1 Y0 E20 F3000; Move Y to center and prime/wipe nozzle.\nG92 E0; extruder reset
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 1
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 45
temperature = 180
thin_walls = 1
threads = 4
toolchange_gcode =
top_infill_extrusion_width = 0
top_solid_infill_speed = 25
top_solid_layers = 2
travel_speed = 50
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 10
wipe = 0
z_offset = 0