Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- # sudo smartctl -d ata -a /dev/sdi
- smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-32-generic] (local build)
- Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
- === START OF INFORMATION SECTION ===
- Device Model: CSSD-V60GB2
- Serial Number: 1149815000FF0646030a
- Firmware Version: 1.1
- User Capacity: 60,022,480,896 bytes [60.0 GB]
- Sector Size: 512 bytes logical/physical
- Device is: Not in smartctl database [for details use: -P showall]
- ATA Version is: 8
- ATA Standard is: Exact ATA specification draft version not indicated
- Local Time is: Fri Nov 2 19:45:14 2012 CDT
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x00) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Disabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 255) seconds.
- Offline data collection
- capabilities: (0x1b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- No Conveyance Self-test supported.
- No Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 1) minutes.
- Extended self-test routine
- recommended polling time: ( 2) minutes.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 5046272
- 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 1724
- 12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 33
- 168 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 0
- 170 Unknown_Attribute 0x0003 100 100 010 Pre-fail Always - 34359738384
- 173 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 41358195
- 192 Power-Off_Retract_Count 0x0012 100 100 000 Old_age Always - 0
- 218 Unknown_Attribute 0x000b 100 100 050 Pre-fail Always - 0
- SMART Error Log Version: 1
- ATA Error Count: 55 (device log contains only the most recent five errors)
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 55 occurred at disk power-on lifetime: 17 hours (0 days + 17 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 c0 a8 27 07 e2 Error: UNC 192 sectors at LBA = 0x020727a8 = 34023336
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- c8 00 c0 a8 27 07 e2 00 17d+00:33:03.000 READ DMA
- c8 00 c0 a8 27 07 e2 00 17d+00:33:02.750 READ DMA
- ef 10 02 00 00 00 a0 00 17d+00:33:02.750 SET FEATURES [Reserved for Serial ATA]
- 27 00 00 00 00 00 e0 00 17d+00:33:02.750 READ NATIVE MAX ADDRESS EXT
- ec 00 00 00 00 00 a0 00 17d+00:33:02.750 IDENTIFY DEVICE
- Error 54 occurred at disk power-on lifetime: 17 hours (0 days + 17 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 c0 a8 27 07 e2 Error: UNC 192 sectors at LBA = 0x020727a8 = 34023336
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- c8 00 c0 a8 27 07 e2 00 17d+00:33:02.750 READ DMA
- ef 10 02 00 00 00 a0 00 17d+00:33:02.750 SET FEATURES [Reserved for Serial ATA]
- 27 00 00 00 00 00 e0 00 17d+00:33:02.750 READ NATIVE MAX ADDRESS EXT
- ec 00 00 00 00 00 a0 00 17d+00:33:02.750 IDENTIFY DEVICE
- ef 03 45 00 00 00 a0 00 17d+00:33:02.750 SET FEATURES [Set transfer mode]
- Error 53 occurred at disk power-on lifetime: 17 hours (0 days + 17 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 c0 a8 27 07 e2 Error: UNC 192 sectors at LBA = 0x020727a8 = 34023336
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- c8 00 c0 a8 27 07 e2 00 17d+00:33:02.250 READ DMA
- c8 00 c0 a8 27 07 e2 00 17d+00:33:01.750 READ DMA
- ef 10 02 00 00 00 a0 00 17d+00:33:01.750 SET FEATURES [Reserved for Serial ATA]
- 27 00 00 00 00 00 e0 00 17d+00:33:01.750 READ NATIVE MAX ADDRESS EXT
- ec 00 00 00 00 00 a0 00 17d+00:33:01.750 IDENTIFY DEVICE
- Error 52 occurred at disk power-on lifetime: 17 hours (0 days + 17 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 c0 a8 27 07 e2 Error: UNC 192 sectors at LBA = 0x020727a8 = 34023336
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- c8 00 c0 a8 27 07 e2 00 17d+00:33:01.750 READ DMA
- ef 10 02 00 00 00 a0 00 17d+00:33:01.750 SET FEATURES [Reserved for Serial ATA]
- 27 00 00 00 00 00 e0 00 17d+00:33:01.750 READ NATIVE MAX ADDRESS EXT
- ec 00 00 00 00 00 a0 00 17d+00:33:01.750 IDENTIFY DEVICE
- ef 03 45 00 00 00 a0 00 17d+00:33:01.750 SET FEATURES [Set transfer mode]
- Error 51 occurred at disk power-on lifetime: 17 hours (0 days + 17 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 c0 a8 27 07 e2 Error: UNC 192 sectors at LBA = 0x020727a8 = 34023336
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- c8 00 c0 a8 27 07 e2 00 17d+00:33:01.250 READ DMA
- c8 00 c0 a8 27 07 e2 00 17d+00:33:01.000 READ DMA
- ef 10 02 00 00 00 a0 00 17d+00:33:01.000 SET FEATURES [Reserved for Serial ATA]
- 27 00 00 00 00 00 e0 00 17d+00:33:01.000 READ NATIVE MAX ADDRESS EXT
- ec 00 00 00 00 00 a0 00 17d+00:33:01.000 IDENTIFY DEVICE
- SMART Self-test log structure revision number 1
- No self-tests have been logged. [To run self-tests, use: smartctl -t]
- Device does not support Selective Self Tests/Logging
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement