Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- Welcome to minicom 2.5
- OPTIONS: I18n
- Port /dev/ttyUSB0
- Press CTRL-A Z for help on special keys
- +
- AR8316 PHY found on MAC0
- AR8316 PHY found on MAC1
- Ethernet eth0: MAC address 00:15:6d:c1:c8:b9
- IP: 192.168.1.20/255.255.255.0, Gateway: 0.0.0.0
- Default server: 0.0.0.0
- RedBoot(tm) bootstrap and debug environment [ROMRAM]
- Ubiquiti Networks certified release, version 0.9.00318M.0905121200 - built 12:01:38, May 12 2009
- Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.
- Board: Ubiquiti RouterStation PRO
- Arch: ar7100pro
- RAM: 0x80000000-0x88000000, [0x8003bf00-0x87fe1000] available
- Flash: 0xbf000000-0xc0000000, in 256 blocks of 0x00010000 bytes each
- == Executing boot script in 2.000 seconds - enter ^C to abort
- RedBoot> fis load -d -e kernel
- Trying LZMA decompression...
- Image loaded from 0x80060000-0x80303ba0
- Image is not ELF, skipping ELF parsing...
- RedBoot> exec
- Now booting linux kernel:
- Base address 0x80050000 Entry 0x80060000
- memsize=0x08000000
- modetty0=0,n,8,1,hw
- board=RouterStation PRO
- ethaddr=00.15.6d.c1.c8.b9
- [ 0.000000] Linux version 2.6.39.4 (openwrt@OpenWRTBuild) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 Sun Jan 1 08:47:23 MST 22
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
- [ 0.000000] SoC: Atheros AR7161 rev 2
- [ 0.000000] Clocks: CPU:800.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 08000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone PFN ranges:
- [ 0.000000] Normal 0x00000000 -> 0x00008000
- [ 0.000000] Movable zone start PFN for each node
- [ 0.000000] early_node_map[1] active PFN ranges
- [ 0.000000] 0: 0x00000000 -> 0x00008000
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
- [ 0.000000] Kernel command line: board=UBNT-RSPRO console=ttyS0,115200 ethaddr=00.15.6d.c1.c8.b9 rootfstype=squashfs,jffs2 noinitrd
- [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
- [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
- [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
- [ 0.000000] Writing ErrCtl register=00002002
- [ 0.000000] Readback ErrCtl register=00002002
- [ 0.000000] Memory: 126712k/131072k available (2113k kernel code, 4360k reserved, 401k data, 188k init, 0k highmem)
- [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:80
- [ 0.000000] Calibrating delay loop... 531.66 BogoMIPS (lpj=2658304)
- [ 0.060000] pid_max: default: 32768 minimum: 301
- [ 0.060000] Mount-cache hash table entries: 512
- [ 0.070000] NET: Registered protocol family 16
- [ 0.070000] MIPS: machine is Ubiquiti RouterStation Pro
- [ 0.370000] registering PCI controller with io_map_base unset
- [ 2.670000] bio: create slab <bio-0> at 0
- [ 2.680000] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
- [ 2.680000] pci 0000:00:11.0: BAR 0: set to [mem 0x10000000-0x1000ffff] (PCI address [0x10000000-0x1000ffff])
- [ 2.690000] PCI: mapping irq 72 to pin1@0000:00:11.0
- [ 2.690000] Switching to clocksource MIPS
- [ 2.700000] NET: Registered protocol family 2
- [ 2.700000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 2.700000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
- [ 2.710000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
- [ 2.710000] TCP: Hash tables configured (established 4096 bind 4096)
- [ 2.720000] TCP reno registered
- [ 2.720000] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 2.730000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 2.730000] NET: Registered protocol family 1
- [ 2.750000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 2.750000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 2.760000] msgmni has been set to 247
- [ 2.770000] io scheduler noop registered
- [ 2.770000] io scheduler deadline registered (default)
- [ 2.770000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
- [ 2.800000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
- [ 2.810000] console [ttyS0] enabled, bootconsole disabled
- [ 2.810000] console [ttyS0] enabled, bootconsole disabled
- [ 2.820000] Atheros AR71xx SPI Controller driver version 0.2.4
- [ 2.830000] m25p80 spi0.0: found mx25l12805d, expected m25p80
- [ 2.830000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
- [ 2.840000] Searching for RedBoot partition table in spi0.0 at offset 0xfe0000
- [ 2.920000] Searching for RedBoot partition table in spi0.0 at offset 0xff0000
- [ 2.990000] 5 RedBoot partitions found on MTD device spi0.0
- [ 3.000000] Creating 5 MTD partitions on "spi0.0":
- [ 3.000000] 0x000000000000-0x000000030000 : "RedBoot"
- [ 3.010000] 0x000000030000-0x000000110000 : "kernel"
- [ 3.020000] 0x000000110000-0x000000ff0000 : "rootfs"
- [ 3.020000] mtd: partition "rootfs" set to be root filesystem
- [ 3.030000] split_squashfs: no squashfs found in "spi0.0"
- [ 3.030000] 0x000000ff0000-0x000000fff000 : "FIS directory"
- [ 3.040000] 0x000000fff000-0x000001000000 : "RedBoot config"
- [ 4.090000] ag71xx_mdio: probed
- [ 4.090000] eth0: Atheros AG71xx at 0xb9000000, irq 4
- [ 4.610000] eth1: Atheros AG71xx at 0xba000000, irq 5
- [ 4.910000] Atheros AR71xx hardware watchdog driver version 0.1.0
- [ 4.920000] TCP westwood registered
- [ 4.920000] NET: Registered protocol family 17
- [ 4.930000] Bridge firewalling registered
- [ 4.930000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
- [ 4.940000] All bugs added by David S. Miller <davem@redhat.com>
- [ 6.490000] JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, .
- [ 6.510000] VFS: Mounted root (jffs2 filesystem) readonly on device 31:2.
- [ 6.510000] Freeing unused kernel memory: 188k freed
- [ 10.000000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
- [ 10.020000] Button Hotplug driver version 0.4.1
- - preinit -
- Press the [f] key and hit [enter] to enter failsafe mode
- [ 12.610000] eth0: link up (100Mbps/Full duplex)
- - regular preinit -
- [ 13.460000] SCSI subsystem initialized
- [ 13.640000] usbcore: registered new interface driver usbfs
- [ 13.640000] usbcore: registered new interface driver hub
- [ 13.650000] usbcore: registered new device driver usb
- [ 14.140000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 14.150000] ar71xx-ehci ar71xx-ehci: Atheros AR71xx built-in EHCI controller
- [ 14.150000] ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
- [ 14.190000] ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
- [ 14.210000] ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
- [ 14.210000] hub 1-0:1.0: USB hub found
- [ 14.220000] hub 1-0:1.0: 2 ports detected
- [ 14.260000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 14.260000] ar71xx-ohci ar71xx-ohci: Atheros AR71xx built-in OHCI controller
- [ 14.270000] ar71xx-ohci ar71xx-ohci: new USB bus registered, assigned bus number 2
- [ 14.280000] ar71xx-ohci ar71xx-ohci: irq 14, io mem 0x1c000000
- [ 14.340000] hub 2-0:1.0: USB hub found
- [ 14.340000] hub 2-0:1.0: 2 ports detected
- [ 14.420000] Initializing USB Mass Storage driver...
- [ 14.420000] usbcore: registered new interface driver usb-storage
- [ 14.430000] USB Mass Storage support registered.
- [ 14.550000] usb 1-1: new high speed USB device number 2 using ar71xx-ehci
- [ 14.700000] hub 1-1:1.0: USB hub found
- [ 14.700000] hub 1-1:1.0: 4 ports detected
- [ 14.830000] usb 1-2: new high speed USB device number 3 using ar71xx-ehci
- [ 14.990000] usb-storage 1-2:1.0: Quirks match for vid 05e3 pid 0723: 8000
- [ 15.000000] scsi0 : usb-storage 1-2:1.0
- [ 15.100000] usb 1-1.1: new high speed USB device number 4 using ar71xx-ehci
- [ 15.220000] scsi1 : usb-storage 1-1.1:1.0
- [ 15.300000] usb 1-1.2: new low speed USB device number 5 using ar71xx-ehci
- [ 16.000000] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 9451 PQ: 0 ANSI: 0
- [ 16.010000] sd 0:0:0:0: [sda] Attached SCSI removable disk
- [ 16.220000] scsi 1:0:0:0: Direct-Access SAMSUNG HD502IJ PQ: 0 ANSI: 2 CCS
- [ 16.230000] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
- [ 16.230000] sd 1:0:0:0: [sdb] Write Protect is off
- [ 16.240000] sd 1:0:0:0: [sdb] Assuming drive cache: write through
- [ 16.250000] sd 1:0:0:0: [sdb] Assuming drive cache: write through
- [ 16.260000] sdb: sdb1 sdb2 sdb3
- [ 16.270000] sd 1:0:0:0: [sdb] Assuming drive cache: write through
- [ 16.270000] sd 1:0:0:0: [sdb] Attached SCSI disk
- - init -
- [ 34.540000] eth0: link down
- Please press Enter to activate this console. [ 35.170000] Compat-wireless backport release: compat-wireless-2011-11-29
- [ 35.170000] Backport based on wireless-testing.git master-2011-12-01
- [ 35.380000] cfg80211: Calling CRDA to update world regulatory domain
- [ 35.480000] cfg80211: World regulatory domain updated:
- [ 35.480000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 35.490000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 35.500000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 35.510000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 35.510000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 35.520000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 36.430000] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
- [ 38.000000] ieee80211 phy0: Atheros AR9160 MAC/BB Rev:1 AR5133 RF Rev:b0 mem=0xb0000000, irq=72
- [ 38.020000] cfg80211: Calling CRDA for country: AM
- [ 38.050000] cfg80211: Regulatory domain changed to country: AM
- [ 38.050000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 38.060000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 38.070000] cfg80211: (5170000 KHz - 5250000 KHz @ 20000 KHz), (N/A, 1800 mBm)
- [ 38.080000] cfg80211: (5250000 KHz - 5330000 KHz @ 20000 KHz), (N/A, 1800 mBm)
- [ 38.410000] RPC: Registered udp transport module.
- [ 38.420000] RPC: Registered tcp transport module.
- [ 38.420000] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 38.590000] PPP generic driver version 2.4.2
- [ 38.650000] tun: Universal TUN/TAP device driver, 1.6
- [ 38.650000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- [ 38.950000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
- [ 39.040000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 39.250000] NET: Registered protocol family 24
- [ 39.450000] nf_conntrack version 0.5.0 (1982 buckets, 7928 max)
- [ 39.740000] xt_time: kernel timezone is -0000
- [ 41.020000] ar71xx: pll_reg 0xb8050010: 0x1099
- [ 41.020000] eth0: link up (100Mbps/Full duplex)
- [ 41.210000] Adding 2048280k swap on /dev/sdb2. Priority:-1 extents:1 across:2048280k
- [ 42.730000] EXT4-fs (sdb3): mounted filesystem with ordered data mode. Opts: (null)
- [ 44.200000] device wlan0 entered promiscuous mode
- [ 46.620000] ar71xx-wdt: enabling watchdog timer
- [ 47.660000] device eth0.5 entered promiscuous mode
- [ 47.660000] device eth0 entered promiscuous mode
- [ 49.150000] device wlan0 left promiscuous mode
- [ 49.150000] br-lan: port 1(wlan0) entering disabled state
- [ 49.270000] device wlan0 entered promiscuous mode
- [ 51.160000] br-lan: port 1(wlan0) entering forwarding state
- [ 51.170000] br-lan: port 1(wlan0) entering forwarding state
- [ 51.170000] br-lan: port 2(eth0.5) entering forwarding state
- [ 51.180000] br-lan: port 2(eth0.5) entering forwarding state
- [ 66.200000] br-lan: port 1(wlan0) entering forwarding state
- [ 66.200000] br-lan: port 2(eth0.5) entering forwarding state
- BusyBox v1.19.3 (2011-12-31 21:23:18 MST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- ATTITUDE ADJUSTMENT (bleeding edge, r29903) ----------
- * 1/4 oz Vodka Pour all ingredients into mixing
- * 1/4 oz Gin tin with ice, strain into glass.
- * 1/4 oz Amaretto
- * 1/4 oz Triple sec
- * 1/4 oz Peach schnapps
- * 1/4 oz Sour mix
- * 1 splash Cranberry juice -----------------------------------------------------
- root@levinet-gate:/# swconfig dev eth1 show
- Failed to connect to the switch
- root@levinet-gate:/#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement