Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- # NOTE Lines must not exceed 132 characters
- # Robot module configurations : general handling of movement G-codes and slicing into moves
- default_feed_rate 4000 # Default rate ( mm/minute ) for G1/G2/G3 moves
- default_seek_rate 4000 # Default rate ( mm/minute ) for G0 moves
- mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs 0 to disable
- mm_max_arc_error 0.01 # The maximum error for line segments that divide arcs 0 to disable
- # note it is invalid for both the above be 0
- # if both are used, will use largest segment length based on radius
- #mm_per_line_segment 0.5 # Lines can be cut into segments ( not useful with cartesian
- # coordinates robots ).
- delta_segments_per_second 100 # for deltas only same as in Marlin/Delta, set to 0 to disable
- # and use mm_per_line_segment
- # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
- arm_solution linear_delta # selects the delta arm solution
- alpha_steps_per_mm 100 # Steps per mm for alpha stepper
- beta_steps_per_mm 100 # Steps per mm for beta stepper
- gamma_steps_per_mm 100 # Steps per mm for gamma stepper
- arm_length 495.0 # this is the length of an arm from hinge to hinge
- arm_radius 258.4833 # this is the horizontal distance from hinge to hinge
- # when the effector is centered
- # Planner module configuration : Look-ahead and acceleration configuration
- planner_queue_size 32 # DO NOT CHANGE THIS UNLESS YOU KNOW EXACTLY WHAT YOU ARE DOING
- acceleration 3000 # Acceleration in mm/second/second.
- junction_deviation 0.05 # Similar to the old "max_jerk", in millimeters,
- # see https://github.com/grbl/grbl/blob/master/planner.c#L409
- # and https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.8
- # Lower values mean being more careful, higher values means being
- # faster and have more jerk
- #minimum_planner_speed 0.0 # sets the minimum planner speed in mm/sec
- # Stepper module configuration
- microseconds_per_step_pulse 1 # Duration of step pulses to stepper drivers, in microseconds
- base_stepping_frequency 100000 # Base frequency for stepping
- # Cartesian axis speed limits
- x_axis_max_speed 30000 # mm/min
- y_axis_max_speed 30000 # mm/min
- z_axis_max_speed 30000 # mm/min
- # Stepper module pins ( ports, and pin numbers, appending "!" to the number will invert a pin )
- alpha_step_pin 2.0 # Pin for alpha stepper step signal
- alpha_dir_pin 0.5 # Pin for alpha stepper direction
- alpha_en_pin 0.4 # Pin for alpha enable pin
- alpha_current 1.26 # X stepper motor current
- alpha_max_rate 30000.0 # mm/min
- beta_step_pin 2.1 # Pin for beta stepper step signal
- beta_dir_pin 0.11 # Pin for beta stepper direction
- beta_en_pin 0.10 # Pin for beta enable
- beta_current 1.26 # Y stepper motor current
- beta_max_rate 30000.0 # mm/min
- gamma_step_pin 2.2 # Pin for gamma stepper step signal
- gamma_dir_pin 0.20 # Pin for gamma stepper direction
- gamma_en_pin 0.19 # Pin for gamma enable
- gamma_current 1.26 # Z stepper motor current
- gamma_max_rate 30000.0 # mm/min
- # Serial communications configuration ( baud rate default to 9600 if undefined )
- uart0.baud_rate 115200 # Baud rate for the default hardware serial port
- second_usb_serial_enable false # This enables a second usb serial port (to have both pronterface
- # and a terminal connected)
- leds_disable true # disable using leds after config loaded
- #msd_disable false # disable the MSD (USB SDCARD) when set to true
- #dfu_enable false # for linux developers, set to true to enable DFU
- #watchdog_timeout 10 # watchdog timeout in seconds, default is 10, set to 0 to disable the watchdog
- # Extruder module configuration
- extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
- extruder.hotend.steps_per_mm 2600 # Steps per mm for extruder stepper
- extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
- extruder.hotend.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
- extruder.hotend.max_speed 50 # mm/s
- extruder.hotend.step_pin 2.3 # Pin for extruder step signal
- extruder.hotend.dir_pin 0.22! # 0.22 # Pin for extruder dir signal
- extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
- # extruder offset
- #extruder.hotend.x_offset 0 # x offset from origin in mm
- #extruder.hotend.y_offset 0 # y offset from origin in mm
- #extruder.hotend.z_offset 0 # z offset from origin in mm
- # firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
- #extruder.hotend.retract_length 3 # retract length in mm
- #extruder.hotend.retract_feedrate 45 # retract feedrate in mm/sec
- #extruder.hotend.retract_recover_length 0 # additional length for recover
- #extruder.hotend.retract_recover_feedrate 8 # recover feedrate in mm/sec (should be less than retract feedrate)
- #extruder.hotend.retract_zlift_length 0 # zlift on retract in mm, 0 disables
- #extruder.hotend.retract_zlift_feedrate 6000 # zlift feedrate in mm/min (Note mm/min NOT mm/sec)
- delta_current 0.455 # First extruder stepper motor current
- # Second extruder module configuration example
- #extruder.hotend2.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
- #extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper
- #extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
- #extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
- #extruder.hotend2.max_speed 50 # mm/s
- #extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
- #extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal
- #extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
- #extruder.hotend2.x_offset 0 # x offset from origin in mm
- #extruder.hotend2.y_offset 25.0 # y offset from origin in mm
- #extruder.hotend2.z_offset 0 # z offset from origin in mm
- #epsilon_current 1.5 # Second extruder stepper motor current
- # Laser module configuration
- laser_module_enable false # Whether to activate the laser module at all. All configuration is
- # ignored if false.
- #laser_module_pin 2.5 # this pin will be PWMed to control the laser. Only P2.0 - P2.5, P1.18, P1.20, P1.21, P1.23, P1.24, P1.26, P3.25, P3.26
- # can be used since laser requires hardware PWM
- #laser_module_maximum_power 1.0 # this is the maximum duty cycle that will be applied to the laser
- #laser_module_minimum_power 0.0 # This is a value just below the minimum duty cycle that keeps the laser
- # active without actually burning.
- #laser_module_default_power 0.8 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
- # the maximum and minimum power levels specified above
- #laser_module_pwm_period 20 # this sets the pwm frequency as the period in microseconds
- # Hotend temperature control configuration
- temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all.
- # All configuration is ignored if false.
- temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
- temperature_control.hotend.heater_pin 2.7 # Pin that controls the heater
- temperature_control.hotend.thermistor Honeywell100K # see http://smoothieware.org/temperaturecontrol#toc5
- #temperature_control.hotend.beta 4066 # or set the beta value
- temperature_control.hotend.set_m_code 104 #
- temperature_control.hotend.set_and_wait_m_code 109 #
- temperature_control.hotend.designator T #
- temperature_control.hotend.max_temp 240 # Set maximum temperature - Will prevent heating above 300 by default
- #temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below 0 by default
- temperature_control.hotend.p_factor 329.2193 # permanently set the PID values after an auto pid
- temperature_control.hotend.i_factor 30.4129 #
- temperature_control.hotend.d_factor 890.9497 #
- temperature_control.hotend.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
- # Hotend2 temperature control configuration
- #temperature_control.hotend2.enable true # Whether to activate this ( "hotend" ) module at all.
- # All configuration is ignored if false.
- #temperature_control.hotend2.thermistor_pin 0.25 # Pin for the thermistor to read
- #temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater
- #temperature_control.hotend2.thermistor EPCOS100K # http://smoothieware.org/temperaturecontrol#toc5
- ##temperature_control.hotend2.beta 4066 # or set the beta value
- #temperature_control.hotend2.set_m_code 104 #
- #temperature_control.hotend2.set_and_wait_m_code 109 #
- #temperature_control.hotend2.designator T1 #
- #temperature_control.hotend2.p_factor 13.7 # permanently set the PID values after an auto pid
- #temperature_control.hotend2.i_factor 0.097 #
- #temperature_control.hotend2.d_factor 24 #
- #temperature_control.hotend2.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
- temperature_control.bed.enable true #
- temperature_control.bed.thermistor_pin 0.24 #
- temperature_control.bed.heater_pin 2.5 #
- #temperature_control.bed.thermistor Honeywell100K # see http://smoothieware.org/temperaturecontrol#toc5
- temperature_control.bed.beta 3950 # or set the beta value
- temperature_control.bed.set_m_code 140 #
- temperature_control.bed.set_and_wait_m_code 190 #
- temperature_control.bed.designator B #
- #temperature_control.bed.bang_bang false # set to true to use bang bang control rather than PID
- #temperature_control.bed.hysteresis 2.0 # set to the temperature in degrees C to use as hysteresis
- # when using bang bang
- # Switch module for fan control
- switch.fan.enable true #
- switch.fan.input_on_command M106 #
- switch.fan.input_off_command M107 #
- switch.fan.output_pin 2.4w #
- switch.fan.output_type pwm # pwm output settable with S parameter in the input_on_comand
- #switch.fan.max_pwm 255 # set max pwm for the pin default is 255
- #switch.misc.enable true #
- #switch.misc.input_on_command M42 #
- #switch.misc.input_off_command M43 #
- #switch.misc.output_pin 2.4 #
- #switch.misc.output_type digital # just an on or off pin
- # automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
- # useful to turn on a fan or water pump to cool the hotend
- #temperatureswitch.hotend.enable true #
- #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
- #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch
- #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch
- #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
- #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
- # Switch module for spindle control
- #switch.spindle.enable false #
- # Endstops
- endstops_enable true # the endstop module is enabled by default and can be disabled here
- delta_homing true # forces all three axis to home a the same time regardless of
- # what is specified in G28
- alpha_min_endstop nc #
- alpha_max_endstop 1.25- # add ! to invert pullup if switch is NO to ground
- alpha_homing_direction home_to_max # Home up
- alpha_max 0 #
- beta_min_endstop nc #
- beta_max_endstop 1.27- #
- beta_homing_direction home_to_max #
- beta_max 0 #
- gamma_min_endstop nc #
- gamma_max_endstop 1.29- #
- gamma_homing_direction home_to_max #
- gamma_max 300 #
- alpha_max_travel 1400 # max travel in mm for alpha/X axis when homing
- beta_max_travel 1400 # max travel in mm for beta/Y axis when homing
- gamma_max_travel 1400 # max travel in mm for gamma/Z axis when homing
- alpha_fast_homing_rate_mm_s 50 # homing feedrates in mm/second
- beta_fast_homing_rate_mm_s 50 #
- gamma_fast_homing_rate_mm_s 50 #
- alpha_slow_homing_rate_mm_s 20 #
- beta_slow_homing_rate_mm_s 20 #
- gamma_slow_homing_rate_mm_s 20
- alpha_homing_retract_mm 5 # retract/bounce distance after homing in mm
- beta_homing_retract_mm 5 #
- gamma_homing_retract_mm 5 #
- alpha_trim 0 # software trim for alpha stepper endstop (in mm)
- beta_trim 0 # software trim for beta stepper endstop (in mm)
- gamma_trim 0 # software trim for gamma stepper endstop (in mm)
- # optional enable limit switches, actions will stop if any enabled limit switch is triggered (all are set for delta)
- #alpha_limit_enable false # set to true to enable X min and max limit switches
- #beta_limit_enable false # set to true to enable Y min and max limit switches
- #gamma_limit_enable false # set to true to enable Z min and max limit switches
- #move_to_origin_after_home true # move XY to 0,0 after homing
- #endstop_debounce_count 100 # uncomment if you get noise on your endstops
- # optional Z probe
- zprobe.enable true # false # set to true to enable a zprobe
- zprobe.probe_pin 1.28^ # pin probe is attached to if NC remove the !
- zprobe.slow_feedrate 30 # mm/sec probe feed rate
- #zprobe.debounce_count 100 # set if noisy
- zprobe.fast_feedrate 50 # move feedrate mm/sec
- zprobe.probe_height 50 # how much above bed to start probe
- #gamma_min_endstop nc # normally 1.28. Change to nc to prevent conflict,
- # associated with zprobe the leveling strategy to use
- leveling-strategy.delta-calibration.enable true # basic delta calibration
- leveling-strategy.delta-calibration.radius 200 # the probe radius
- leveling-strategy.delta-calibration.initial_height 50 #
- #for the G31 command
- leveling-strategy.delta-grid.enable true # Allows grid probe compensation
- leveling-strategy.delta-grid.radius 200 # The radius to probe inside
- leveling-strategy.delta-grid.size 11 # The side of the grid, 11x11
- leveling-strategy.delta-grid.save true # Saves the grid to be loaded on boot
- leveling-strategy.delta-grid.initial_height 50 # Initial height to start probing
- # kill button (used to be called pause) maybe assigned to a different pin, set to the onboard pin by default
- kill_button_enable true # set to true to enable a kill button
- kill_button_pin 2.12 # kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
- # Panel
- panel.enable false # set to true to enable the panel code
- panel.lcd smoothiepanel # set type of panel
- panel.encoder_a_pin 3.25!^ # encoder pin
- panel.encoder_b_pin 3.26!^ # encoder pin
- # Example for reprap discount GLCD
- # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
- # +5v is EXP1 pin 10, Gnd is EXP1 pin 9
- #panel.lcd reprap_discount_glcd #
- #panel.spi_channel 0 # spi channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
- #panel.spi_cs_pin 0.16 # spi chip select ; GLCD EXP1 Pin 4
- #panel.encoder_a_pin 3.25!^ # encoder pin ; GLCD EXP2 Pin 3
- #panel.encoder_b_pin 3.26!^ # encoder pin ; GLCD EXP2 Pin 5
- #panel.click_button_pin 1.30!^ # click button ; GLCD EXP1 Pin 2
- #panel.buzz_pin 1.31 # pin for buzzer ; GLCD EXP1 Pin 1
- #panel.button_pause_pin 2.11^ # kill/pause ; GLCD EXP2 Pin 8 either
- #panel.back_button_pin 2.11!^ # back button ; GLCD EXP2 Pin 8 or
- # pins used with other panels
- #panel.up_button_pin 0.1! # up button if used
- #panel.down_button_pin 0.0! # down button if used
- #panel.click_button_pin 0.18! # click button if used
- panel.menu_offset 0 # some panels will need 1 here
- panel.alpha_jog_feedrate 6000 # x jogging feedrate in mm/min
- panel.beta_jog_feedrate 6000 # y jogging feedrate in mm/min
- panel.gamma_jog_feedrate 200 # z jogging feedrate in mm/min
- panel.hotend_temperature 185 # temp to set hotend when preheat is selected
- panel.bed_temperature 60 # temp to set bed when preheat is selected
- # Example of a custom menu entry, which will show up in the Custom entry.
- # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
- custom_menu.power_on.enable true #
- custom_menu.power_on.name Power_on #
- custom_menu.power_on.command M80 #
- custom_menu.power_off.enable true #
- custom_menu.power_off.name Power_off #
- custom_menu.power_off.command M81 #
- # Only needed on a smoothieboard
- currentcontrol_module_enable true #
- return_error_on_unhandled_gcode false #
- # network settings
- network.enable true # enable the ethernet network services
- network.webserver.enable true # enable the webserver
- network.telnet.enable true # enable the telnet server
- #network.ip_address auto # use dhcp to get ip address
- # uncomment the 3 below to manually setup ip address
- network.ip_address 192.168.1.15 # the IP address
- network.ip_mask 255.255.255.0 # the ip mask
- network.ip_gateway 192.168.1.1 # the gateway address
- #network.mac_override xx.xx.xx.xx.xx.xx # override the mac address, only do this if you have a conflict
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement