U-Boot SPL 2013.01-rc1-04928-g9c501f4 (Nov 18 2012 - 13:19:43)
Board: Mele_A3700
DRAM: 1024MB
SUNXI SD/MMC: 0


U-Boot 2013.01-rc1-04928-g9c501f4 (Nov 18 2012 - 13:19:43) Allwinner Technology

CPU:   SUNXI Family
Board: Mele_A3700
I2C:   ready
DRAM:  1 GiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   wemac
Hit any key to stop autoboot:  0
reading uEnv.txt
** Unable to read file uEnv.txt **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
reading boot.scr
254 bytes read
Jumping to boot.scr
## Executing script at 44000000
reading script.bin
44608 bytes read
reading uImage
4000588 bytes read
## Booting kernel from Legacy Image at 48000000 ...
   Image Name:   Linux-3.0.42+
   Created:      2012-11-19   0:26:11 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4000524 Bytes = 3.8 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

<6>Initializing cgroup subsys cpuset
<5>Linux version 3.0.42+ (curtis@curtmania) (gcc version 4.5.4 (Gentoo 4.5.4 p1.0, pie-0.4.7) ) #3 PREEMPT Sun Nov 18 18:26:31 CST 2012
CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: sun4i
<6>Memory Reserved:
<6>     SYS  : 0x43000000 - 0x4300ffff  (  64 kB)
<6>     VE   : 0x44000000 - 0x48ffffff  (  80 MB)
<6>     G2D  : 0x58000000 - 0x58ffffff  (  16 MB)
Memory policy: ECC disabled, Data cache writeback
<6>BROM Ver: 1100 1100 1623
<6>chip-id: A10 (AW1623 revision C)
<7>On node 0 totalpages: 262144
<7>free_area_init_node: node 0, pgdat c0797854, node_mem_map c0851000
<7>  Normal zone: 1280 pages used for memmap
<7>  Normal zone: 0 pages reserved
<7>  Normal zone: 162560 pages, LIFO batch:31
<7>  HighMem zone: 768 pages used for memmap
<7>  HighMem zone: 97536 pages, LIFO batch:31
<7>pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
<5>Kernel command line: root=/dev/mmcblk0p2 rootwait panic=10 init=/sbin/init ip=192.168.1.199
<6>PID hash table entries: 4096 (order: 2, 16384 bytes)
<6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Memory: 1024MB = 1024MB total
<5>Memory: 932656k/932656k available, 115920k reserved, 393216K highmem
<5>Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0xe8800000 - 0xf0000000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xe8000000   ( 640 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .init : 0xc0008000 - 0xc0031000   ( 164 kB)
      .text : 0xc0031000 - 0xc0759000   (7328 kB)
      .data : 0xc075a000 - 0xc079fa18   ( 279 kB)
       .bss : 0xc079fa3c - 0xc0850d18   ( 709 kB)
<6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
<6>NR_IRQS:96 nr_irqs:96 96
<6>timer0: Periodic Mode
<6>Console: colour dummy device 80x30
<6>console [tty0] enabled
<6>Calibrating delay loop... <c>1001.88 BogoMIPS (lpj=5009408)
<6>pid_max: default: 32768 minimum: 301
<6>Mount-cache hash table entries: 512
<6>Initializing cgroup subsys cpuacct
<6>Initializing cgroup subsys devices
<6>Initializing cgroup subsys freezer
<6>Initializing cgroup subsys blkio
<6>CPU: Testing write buffer coherency: ok
<6>hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
<6>devtmpfs: initialized
<6>print_constraints: dummy:
<6>NET: Registered protocol family 16
<6>hw-breakpoint: debug architecture 0x4 unsupported.
[ccmu] try to set apb1 parent to sata_pll failed!
SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics
<6>Initialize DMAC OK
<6>bio: create slab <bio-0> at 0
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>Advanced Linux Sound Architecture Driver Version 1.0.24.
<6>Bluetooth: Core ver 2.16
<6>NET: Registered protocol family 31
<6>Bluetooth: HCI device and connection manager initialized
<6>Bluetooth: HCI socket layer initialized
<6>Bluetooth: L2CAP socket layer initialized
<6>Bluetooth: SCO socket layer initialized
Init eGon pin module V2.0
<6>Switching to clocksource aw 64bits couter
<6>cfg80211: Calling CRDA to update world regulatory domain
<5>FS-Cache: Loaded
<6>CacheFiles: Loaded
<6>Switched to NOHz mode on CPU #0
[usb_manager]: CONFIG_USB_SW_SUN4I_USB0_OTG
[sw_hcd0]: usb host driver initialize........
[sw_hcd0]: open_usb_clock
[sw_hcd0]: host_init_state = 0
[sw_hcd0]: platform is usb host
[sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 38
<6>sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
<6>sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 1 port detected
wrn: hcd is not enable, need not start hcd
[sw_hcd0]: sw_usb_host0_disable start
-------sw_hcd0_soft_disconnect---------
[sw_hcd_host0]: Set USB Power OFF
wrn: hcd is not enable, need not stop hcd
[sw_hcd0]: close_usb_clock
[sw_hcd0]: sw_usb_host0_disable end
[sw_udc]: udc_init: version 20080411
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
<6>TCP: Hash tables configured (established 131072 bind 65536)
<6>TCP reno registered
<6>UDP hash table entries: 512 (order: 1, 8192 bytes)
<6>UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
<6>NET: Registered protocol family 1
<6>RPC: Registered named UNIX socket transport module.
<6>RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
[pm]aw_pm_init!
<6>audit: initializing netlink socket (disabled)
<5>type=2000 audit(0.329:1): initialized
highmem bounce pool size: 64 pages
<5>VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>NTFS driver 2.1.30 [Flags: R/W].
<6>fuse init (API version 7.16)
<6>msgmni has been set to 1053
<6>alg: No test for stdrng (krng)
<6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
<6>io scheduler noop registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<7>G2D: drv_g2d_init
<6>G2D: g2dmem: g2d_start=58000000, g2d_size=1000000
<6>G2D: head:d8000000,tail:d9000000
<6>G2D: Module initialized.major:252
<6>brd: module loaded
<6>loop: module loaded
[NAND]nand driver, init.
cmu_clk is 360
nand clk init end
offset 0xc:  0x26140
offset 0x14:  0x82000008
[NAND] nand gpio_request
[NAND] nand driver version: 0x2 0x9
nand interrupte register ok
ret of NFC_ChangMode is 0
dma_hdle  is 0
dma_hdle  is 10000008
cmu_clk is 360
nand clk init end
offset 0xc:  0x26140
offset 0x14:  0x82000005
The 0 disk name = DEVICE, class name = NAND, disk start = 0, disk size = 15564800
The 1 disk name = bootloader, type = 0, class name = DISK, disk size = 32768
The 2 disk name = env, type = 0, class name = DISK, disk size = 32768
The 3 disk name = boot, type = 0, class name = DISK, disk size = 65536
The 4 disk name = system, type = 0, class name = DISK, disk size = 1048576
The 5 disk name = data, type = 1, class name = DISK, disk size = 3145728
The 6 disk name = misc, type = 0, class name = DISK, disk size = 32768
The 7 disk name = recovery, type = 0, class name = DISK, disk size = 65536
The 8 disk name = cache, type = 0, class name = DISK, disk size = 262144
The 9 disk name = private, type = 0, class name = DISK, disk size = 32768
The 10 disk name = sysrecovery, type = 0, class name = DISK, disk size = 1048576
The 11 disk name = UDISK, type = 0, class name = DISK, disk size = 0
The 11 disk size = 9764864
part total count = 12
<6> nand: unknown partition table
<6> nanda:
<6> nandb: unknown partition table
<6> nandc: unknown partition table
<6> nandd: unknown partition table
<6> nande: unknown partition table
<6> nandf: unknown partition table
<6> nandg: unknown partition table
<6> nandh: unknown partition table
<6> nandi:
<6> nandj: unknown partition table
<6> nandk:
<6>benn: nand probe enter
[NAND]nand driver, ok.
<6>wemac Ethernet Driver, V1.01 in file:/media/ubermedia/Curtis/src/Mele_A3700/Hardfloat_Sandbox/linux-sunxi/drivers/net/sun4i/sun4i_wemac.c
<6>[EMAC] ahb clk enable
<6>[EMAC] ahb gate clk: 0x26140
<6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[sw-ehci1]: open clock
[sw-ehci1]: Set USB Power ON
<6>sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
<6>sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
<6>sw-ehci sw-ehci.1: irq 39, io mem 0xf1c14000
<6>sw-ehci sw-ehci.1: USB 0.0 started, EHCI 1.00
ehci_irq: port change detect
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 1 port detected
[sw-ohci1]: open clock
<6>sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
<6>sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
<6>sw-ohci sw-ohci.1: irq 64, io mem 0xf1c14400
<6>hub 3-0:1.0: USB hub found
<6>hub 3-0:1.0: 1 port detected
[sw-ehci2]: open clock
[sw-ehci2]: Set USB Power ON
<6>sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
<6>sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4
<6>sw-ehci sw-ehci.2: irq 40, io mem 0xf1c1c000
<6>sw-ehci sw-ehci.2: USB 0.0 started, EHCI 1.00
ehci_irq: port change detect
<6>hub 4-0:1.0: USB hub found
<6>hub 4-0:1.0: 1 port detected
<6>[sw-ehci2]: disable ehci
<6>sw-ehci sw-ehci.2: remove, state 1
<6>usb usb4: USB disconnect, device number 1
<6>sw-ehci sw-ehci.2: USB bus 4 deregistered
[sw-ehci2]: Set USB Power OFF
[sw-ehci2]: close clock
[sw-ohci2]: open clock
[sw-ohci2]: Set USB Power ON
<6>sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
<6>sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 4
<6>sw-ohci sw-ohci.2: irq 65, io mem 0xf1c1c400
<6>hub 4-0:1.0: USB hub found
<6>hub 4-0:1.0: 1 port detected
<6>[sw-ohci2]: disable ohci
<6>sw-ohci sw-ohci.2: remove, state 1
<6>usb usb4: USB disconnect, device number 1
<6>usb 2-1: new high speed USB device number 2 using sw-ehci
<6>sw-ohci sw-ohci.2: USB bus 4 deregistered
[sw-ohci2]: Set USB Power OFF
[sw-ohci2]: close clock
<6>Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<6>usbcore: registered new interface driver ums-alauda
<6>usbcore: registered new interface driver ums-cypress
<6>usbcore: registered new interface driver ums-datafab
<6>usbcore: registered new interface driver ums_eneub6250
<6>usbcore: registered new interface driver ums-freecom
<6>usbcore: registered new interface driver ums-isd200
<6>usbcore: registered new interface driver ums-jumpshot
<6>usbcore: registered new interface driver ums-karma
<6>usbcore: registered new interface driver ums-onetouch
<6>usbcore: registered new interface driver ums-realtek
<6>usbcore: registered new interface driver ums-sddr09
<6>usbcore: registered new interface driver ums-sddr55
<6>usbcore: registered new interface driver ums-usbat
<6>mousedev: PS/2 mouse device common for all mice
sunxi RTC version 0.1
<6>sunxi-rtc sunxi-rtc: sunxi_rtc_probe tmp_data = 380239881
<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
<6>sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:5
<6>using rtc device, rtc, for alarms<6>sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0
<6>i2c /dev entries driver
!!! base_Addr = 0xe88bcc00
config i2c gpio with gpio_config api
twi0, apb clock = 24000000
<6>axp_mfd 0-0034: AXP (CHIP ID: 0x21) detected
<6>I2C: i2c-0: AW16XX I2C adapter
**********start************
0x40
0xf8
0x28
0x0
0x0
**********end************
!!! base_Addr = 0xe88be000
twi1, apb clock = 24000000
<6>I2C: i2c-1: AW16XX I2C adapter
**********start************
0x40
0xf8
<6>hub 2-1:1.0: USB hub found
0x58
<6>hub 2-1:1.0: 4 ports detected
0x0
0x0
**********end************
!!! base_Addr = 0xe88d2400
twi2, apb clock = 24000000
<6>I2C: i2c-2: AW16XX I2C adapter
**********start************
0x40
0xf8
0x58
0x0
0x0
**********end************
<6>lirc_dev: IR Remote Control driver registered, major 251
<6>IR NEC protocol handler initialized
<6>IR RC5(x) protocol handler initialized
<6>IR RC6 protocol handler initialized
<6>IR JVC protocol handler initialized
<6>IR Sony protocol handler initialized
<6>IR RC5 (streamzap) protocol handler initialized
<6>IR LIRC bridge handler initialized
<6>Linux video capture interface: v2.00
[cedar dev]: install start!!!
[cedar dev]: install end!!!
[ace_drv] start!!!
[ace_drv] init end!!!
[pa_drv] start!!!
[pa_drv] init end!!!
<6>print_constraints: axp20_ldo1: 1300 mV
<6>print_constraints: axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
<6>print_constraints: axp20_ldo3: 700 <--> 3500 mV at 2800 mV
<6>print_constraints: axp20_ldo4: 1250 <--> 3300 mV at 2800 mV
<6>print_constraints: axp20_buck2: 700 <--> 2275 mV at 1400 mV
<6>print_constraints: axp20_buck3: 700 <--> 3500 mV at 1250 mV
<6>print_constraints: axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
<6>input: axp20-supplyer as /devices/platform/sun4i-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0
<6>Bluetooth: HCI UART driver ver 2.2
<6>Bluetooth: HCI H4 protocol initialized
<6>Bluetooth: HCI BCSP protocol initialized
<6>Bluetooth: HCILL protocol initialized
<6>cpuidle: using governor ladder
<6>cpuidle: using governor menu
[mmc_pm]: no sdio card used in configuration
[mmc]: sunximmc_init
[mmc]: sunxi mmc controller using config : 0xb
[mmc]: sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0
[mmc]: mmc 0 power off !!
[mmc]: mmc0 Probe: base:0xe88da000 irq:32 dma:0 pdes:0xe7bf8000, ret 0.
[mmc]: sunxi-mmc.1: pdev->name: sunxi-mmc, pdev->id: 1
[mmc]: mmc 1 power off !!
[mmc]: mmc1 Probe: base:0xe88dc000 irq:33 dma:0 pdes:0xe7000000, ret 0.
[mmc]: sunxi-mmc.3: pdev->name: sunxi-mmc, pdev->id: 3
[mmc]: mmc 3 power off !!
[mmc]: mmc3 Probe: base:0xe88de000 irq:35 dma:0 pdes:0xe7004000, ret 0.
<6>usbcore: registered new interface driver usbhid
<6>usbhid: USB HID core driver
enter sun4i Audio codec!!!
<6>sun4i audio support initialized
sun4i Audio codec successfully loaded..
<6>asoc: sndhdmi <-> sun4i-hdmiaudio.0 mapping ok
<6>ALSA device list:
<6>  #0: sun4i-CODEC  Audio Codec
<6>  #1: sun4i-sndhdmi
<6>IPv4 over IPv4 tunneling driver
<6>TCP cubic registered
<6>Initializing XFRM netlink socket
<6>NET: Registered protocol family 10
<6>NET: Registered protocol family 17
<6>NET: Registered protocol family 15
<6>Bluetooth: RFCOMM TTY layer initialized
<6>Bluetooth: RFCOMM socket layer initialized
<6>Bluetooth: RFCOMM ver 1.11
<6>Bluetooth: BNEP (Ethernet Emulation) ver 1.3
<6>Bluetooth: BNEP filters: protocol multicast
<6>802.1Q VLAN Support v1.8
[mmc_pm]: No sdio card, please check your config !!
<6>VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
<5>Registering SWP/SWPB emulation handler
<6>registered taskstats version 1
<4>regulator_init_complete: axp20_buck3: incomplete constraints, leaving on
<4>regulator_init_complete: axp20_buck2: incomplete constraints, leaving on
<4>regulator_init_complete: axp20_ldo4: incomplete constraints, leaving on
<4>regulator_init_complete: axp20_ldo3: incomplete constraints, leaving on
<4>regulator_init_complete: axp20_ldo2: incomplete constraints, leaving on
<4>regulator_init_complete: axp20_ldo1: incomplete constraints, leaving on
<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
<6>sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:6
<6>sunxi-rtc sunxi-rtc: setting system clock to 2010-01-01 00:00:06 UTC (1262304006)
<6>Waiting for root device /dev/mmcblk0p2...
[mmc]: mmc 0 detect change, present 1
[mmc]: mmc 0 power on !!
[mmc]: sdxc_request_done(L1113): smc 0 err, cmd 52,  RTO !!
[mmc]: sdxc_request_done(L1113): smc 0 err, cmd 52,  RTO !!
[mmc]: sdxc_request_done(L1113): smc 0 err, cmd 5,  RTO !!
[mmc]: sdxc_request_done(L1113): smc 0 err, cmd 5,  RTO !!
[mmc]: sdxc_request_done(L1113): smc 0 err, cmd 5,  RTO !!
[mmc]: sdxc_request_done(L1113): smc 0 err, cmd 5,  RTO !!
<6>mmc0: new high speed SDHC card at address 0001
<6>mmcblk0: mmc0:0001 00000 29.2 GiB
<6> mmcblk0: p1 p2 p3 p4
<3>EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
<3>EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
<6>EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
<6>VFS: Mounted root (ext4 filesystem) on device 179:2.
<6>devtmpfs: mounted
<6>Freeing init memory: 164K
<30>udevd[327]: starting version 171
sunxi_rtc_open
<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
<6>sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:14
<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
<6>sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:14
<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
<6>sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:14
<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
<6>sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:16
<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
<6>sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:16
<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
<6>sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:16
<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
<6>sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:16
<6>EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
<6>sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:18
<6>Adding 523260k swap on /dev/mmcblk0p3.  Priority:-1 extents:1 across:523260k SS