Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 1.1.3 (Jul 18 2011 - 20:45:26)
- Board: Ralink APSoC DRAM: 64 MB
- relocate_code Pointer at: 83fa8000
- ************** Init GPIO Pin Start **************
- ************** Init GPIO Pin Done **************
- spi_wait_nsec: 30
- spi device id: c2 20 17 c2 20 (2017c220)
- find flash: MX25L6405D
- raspi_read: from:30000 len:1000
- .raspi_read: from:30000 len:1000
- .============================================
- Ralink UBoot Version: 3.5.3.0
- --------------------------------------------
- ASIC 3883_MP (MAC to REALTEK Mode)
- DRAM_CONF_FROM: Boot-Strapping
- DRAM_TYPE: DDR2
- DRAM_SIZE: 512 Mbits
- DRAM_WIDTH: 16 bits
- DRAM_TOTAL_WIDTH: 16 bits
- TOTAL_MEMORY_SIZE: 64 MBytes
- Flash component: SPI Flash
- Date:Jul 18 2011 Time:20:45:26
- ============================================
- icache: sets:512, ways:4, linesz:32 ,total:65536
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- ##### The CPU freq = 500 MHZ ####
- estimate memory size =64 Mbytes
- Realtek giga Mac init!
- regData1 = 0000 regData2 = 0000, RTL8367R
- (rtk_switch_init 11984) init_rgmii done
- Realtek giga Mac done!
- Please choose the operation:
- 0: Load ucos code to SDRAM via TFTP Client.
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP. 0
- flash id = 00000000 sectors = 0 count = 0
- 3: System Boot system code via Flash.
- ## Booting image at bc070000 ...
- raspi_read: from:70000 len:40
- .CSYS magic number at 0xBC070000
- raspi_read: from:70014 len:40
- . Image Name: MIPS OpenWrt Linux-3.18.21
- Created: 2015-10-06 10:18:21 UTC
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1232170 Bytes = 1.2 MB
- Load Address: 80000000
- Entry Point: 80000000
- raspi_read: from:70054 len:12cd2a
- ................... Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 64
- Starting kernel ...
- [ 0.000000] Linux version 3.18.21 (pepe2k@ubuntu1404vm) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47048) ) #45 Tue Oct 6 12:18:13 CEST 2015
- [ 0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
- [ 0.000000] MIPS: machine is Jensen Scandinavia AL3000DG v2
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x03ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Writing ErrCtl register=00000000
- [ 0.000000] Readback ErrCtl register=00000000
- [ 0.000000] Memory: 61036K/65536K available (2760K kernel code, 125K rwdata, 560K rodata, 192K init, 192K bss, 4500K reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] CPU Clock: 500MHz
- [ 0.000000] Calibrating delay loop... 249.44 BogoMIPS (lpj=1247232)
- [ 0.070000] pid_max: default: 32768 minimum: 301
- [ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.090000] pinctrl core: initialized pinctrl subsystem
- [ 0.100000] NET: Registered protocol family 16
- [ 0.110000] rt3883-pci 10140000.pci: mode: PCIe
- [ 1.710000] PCI host bridge /pci@10140000/host-bridge ranges:
- [ 1.720000] MEM 0x0000000020000000..0x000000002fffffff
- [ 1.730000] IO 0x0000000010160000..0x000000001016ffff
- [ 1.750000] rt2880_gpio 10000600.gpio: registering 24 gpios
- [ 1.760000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
- [ 1.770000] rt2880_gpio 10000638.gpio: registering 16 gpios
- [ 1.780000] PCI host bridge to bus 0000:00
- [ 1.780000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
- [ 1.790000] pci_bus 0000:00: root bus resource [io 0xffffffff]
- [ 1.800000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 1.810000] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 1.820000] pci 0000:00:01.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
- [ 1.830000] pci 0000:00:01.0: BAR 1: assigned [mem 0x20100000-0x2010ffff]
- [ 1.840000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x2000ffff]
- [ 1.850000] pci 0000:00:01.0: PCI bridge to [bus 01]
- [ 1.850000] pci 0000:00:01.0: bridge window [mem 0x20000000-0x200fffff]
- [ 1.860000] pci 0000:00:01.0: of_irq_parse_pci() failed with rc=-22
- [ 1.870000] Switched to clocksource MIPS
- [ 1.880000] NET: Registered protocol family 2
- [ 1.880000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 1.900000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 1.910000] TCP: Hash tables configured (established 1024 bind 1024)
- [ 1.920000] TCP: reno registered
- [ 1.930000] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 1.940000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 1.950000] NET: Registered protocol family 1
- [ 1.960000] rt-timer 10000100.timer: maximum frequency is 10131Hz
- [ 1.980000] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 2.010000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 2.020000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 2.040000] msgmni has been set to 119
- [ 2.050000] io scheduler noop registered
- [ 2.060000] io scheduler deadline registered (default)
- [ 2.070000] gpio-export gpio_export: 5 gpio(s) exported
- [ 2.080000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
- [ 2.100000] console [ttyS0] disabled
- [ 2.100000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A
- [ 2.120000] console [ttyS0] enabled
- [ 2.120000] console [ttyS0] enabled
- [ 2.130000] bootconsole [early0] disabled
- [ 2.130000] bootconsole [early0] disabled
- [ 2.160000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
- [ 2.170000] 6 ofpart partitions found on MTD device spi0.0
- [ 2.180000] Creating 6 MTD partitions on "spi0.0":
- [ 2.190000] 0x000000000000-0x000000030000 : "uboot"
- [ 2.200000] 0x000000030000-0x000000040000 : "uboot-env"
- [ 2.210000] 0x000000040000-0x000000050000 : "factory"
- [ 2.220000] 0x000000050000-0x000000070000 : "devdata"
- [ 2.230000] 0x000000070000-0x000000800000 : "firmware"
- [ 2.300000] 0x000000270000-0x000000800000 : "rootfs"
- [ 2.310000] mtd: device 5 (rootfs) set to be root filesystem
- [ 2.320000] 1 squashfs-split partitions found on MTD device rootfs
- [ 2.330000] 0x000000430000-0x000000800000 : "rootfs_data"
- [ 2.350000] rtl8367b rtl8367b: using GPIO pins 1 (SDA) and 2 (SCK)
- [ 2.360000] rtl8367b rtl8367b: RTL8367R-VB chip found
- [ 4.100000] libphy: rtl8367b: probed
- [ 4.110000] ralink_soc_eth 10100000.ethernet: using fixed link parameters
- [ 4.120000] ralink_soc_eth 10100000.ethernet eth0 (uninitialized): link up (1000Mbps/Full duplex)
- [ 4.140000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
- [ 4.160000] rt2880_wdt 10000120.watchdog: Initialized
- [ 4.170000] TCP: cubic registered
- [ 4.170000] NET: Registered protocol family 10
- [ 4.180000] NET: Registered protocol family 17
- [ 4.190000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 4.220000] 8021q: 802.1Q VLAN Support v1.8
- [ 4.240000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 4.260000] Freeing unused kernel memory: 192K (80360000 - 80390000)
- [ 6.260000] init: Console is alive
- [ 6.270000] init: - watchdog -
- [ 8.270000] init: - preinit -
- [ 8.810000] ralink_soc_eth 10100000.ethernet eth0: link up (1000Mbps/Full duplex)
- [ 8.820000] 8021q: adding VLAN 0 to HW filter on device eth0
- [ 8.860000] random: procd urandom read with 13 bits of entropy available
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 12.390000] jffs2: notice: (326) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 12.430000] mount_root: switching to jffs2 overlay
- [ 12.470000] ralink_soc_eth 10100000.ethernet eth0: link down
- [ 12.490000] procd: - early -
- [ 12.490000] procd: - watchdog -
- [ 13.330000] procd: - ubus -
- [ 14.350000] procd: - init -
- Please press Enter to activate this console.
- [ 15.080000] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 15.100000] Loading modules backported from Linux version master-2015-07-21-0-g47cd203
- [ 15.120000] Backport generated by backports.git backports-20150626-0-gc1a4168
- [ 15.140000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 15.160000] nf_conntrack version 0.5.0 (956 buckets, 3824 max)
- [ 15.200000] xt_time: kernel timezone is -0000
- [ 15.250000] cfg80211: World regulatory domain updated:
- [ 15.260000] cfg80211: DFS Master region: unset
- [ 15.270000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- [ 15.290000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- [ 15.300000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- [ 15.320000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
- [ 15.340000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
- [ 15.350000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
- [ 15.370000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
- [ 15.390000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- [ 15.410000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
- [ 15.480000] PPP generic driver version 2.4.2
- [ 15.500000] NET: Registered protocol family 24
- [ 15.550000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
- [ 15.560000] rt2800pci 0000:01:00.0: failed to load eeprom property
- [ 15.580000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'rt2x00pci_1_0.eeprom'.
- [ 15.640000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5392, rev 0223 detected
- [ 15.650000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5392 detected
- [ 15.690000] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 3883, rev 0400 detected
- [ 15.700000] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 3853 detected
- [ 24.270000] ralink_soc_eth 10100000.ethernet eth0: link up (1000Mbps/Full duplex)
- [ 24.280000] 8021q: adding VLAN 0 to HW filter on device eth0
- [ 24.300000] device eth0.1 entered promiscuous mode
- [ 24.310000] device eth0 entered promiscuous mode
- [ 24.330000] br-lan: port 1(eth0.1) entered forwarding state
- [ 24.340000] br-lan: port 1(eth0.1) entered forwarding state
- [ 26.340000] br-lan: port 1(eth0.1) entered forwarding state
- [ 26.860000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
- [ 26.890000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.34
- [ 27.100000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 27.110000] device wlan0 entered promiscuous mode
- [ 27.150000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 27.160000] br-lan: port 2(wlan0) entered forwarding state
- [ 27.170000] br-lan: port 2(wlan0) entered forwarding state
- [ 29.170000] br-lan: port 2(wlan0) entered forwarding state
- BusyBox v1.23.2 (2015-10-04 12:54:41 CEST) built-in shell (ash)
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- DESIGNATED DRIVER (Bleeding Edge, r47048)
- -----------------------------------------------------
- * 2 oz. Orange Juice Combine all juices in a
- * 2 oz. Pineapple Juice tall glass filled with
- * 2 oz. Grapefruit Juice ice, stir well.
- * 2 oz. Cranberry Juice
- -----------------------------------------------------
- root@OpenWrt:/#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement