API tools faq
paste
Guest User

My messy smoothie config

a guest
Mar 15th, 2017
143
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
INI file 34.72 KB | None | 0 0
raw download clone embed print report
  1. # Smoothieboard configuration file, see http://smoothieware.org/configuring-smoothie
  2. # NOTE Lines must not exceed 132 characters, and '#' characters mean what follows is ignored
  3. ## Robot module configurations : general handling of movement G-codes and slicing into moves
  4.  
  5. # Basic motion configuration
  6. default_feed_rate                            4000             # Default speed (mm/minute) for G1/G2/G3 moves
  7. default_seek_rate                            4000             # Default speed (mm/minute) for G0 moves
  8. mm_per_arc_segment                           0.5              # Fixed length for line segments that divide arcs, 0 to disable
  9. #mm_per_line_segment                         5                # Cut lines into segments this size
  10. #mm_max_arc_error                            0.01             # The maximum error for line segments that divide arcs 0 to disable
  11.                                                               # note it is invalid for both the above be 0
  12.                                                               # if both are used, will use largest segment length based on radius
  13.  
  14. # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
  15. # See http://smoothieware.org/stepper-motors
  16. arm_solution                                 corexy
  17. alpha_steps_per_mm                           160              # Steps per mm for alpha ( X ) stepper
  18. beta_steps_per_mm                            160              # Steps per mm for beta ( Y ) stepper
  19. gamma_steps_per_mm                           800              # Steps per mm for gamma ( Z ) stepper
  20.  
  21. # Planner module configuration : Look-ahead and acceleration configuration
  22. # See http://smoothieware.org/motion-control
  23. planner_queue_size                           16               # DO NOT CHANGE THIS UNLESS YOU KNOW EXACTLY WHAT YOU ARE DOING
  24. acceleration                                 1500             # Acceleration in mm/second/second.
  25. z_acceleration                               500              # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
  26. junction_deviation                           0.05             # See http://smoothieware.org/motion-control#junction-deviation
  27. #z_junction_deviation                        0.0              # For Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
  28.  
  29. # Cartesian axis speed limits
  30. x_axis_max_speed                             15000            # Maximum speed in mm/min
  31. y_axis_max_speed                             15000            # Maximum speed in mm/min
  32. z_axis_max_speed                             600              # Maximum speed in mm/min
  33.  
  34.  
  35.  
  36. ################################
  37. # Stepper module configuration #
  38. ################################
  39.  
  40. # Pins are defined as  ports, and pin numbers, appending "!" to the number will invert a pin
  41. # See http://smoothieware.org/pin-configuration and http://smoothieware.org/pinout
  42. alpha_step_pin                               2.0              # Pin for alpha stepper step signal
  43. alpha_dir_pin                                0.5              # Pin for alpha stepper direction, add '!' to reverse direction
  44. alpha_en_pin                                 0.4              # Pin for alpha enable pin
  45. alpha_current                                1.2              # X stepper motor current
  46. alpha_max_rate                               30000.0          # Maximum rate in mm/min
  47.  
  48. beta_step_pin                                2.1              # Pin for beta stepper step signal
  49. beta_dir_pin                                 0.11!            # Pin for beta stepper direction, add '!' to reverse direction
  50. beta_en_pin                                  0.10             # Pin for beta enable
  51. beta_current                                 1.2              # Y stepper motor current
  52. beta_max_rate                                30000.0          # Maxmimum rate in mm/min
  53.  
  54. gamma_step_pin                               2.2              # Pin for gamma stepper step signal
  55. gamma_dir_pin                                0.20             # Pin for gamma stepper direction, add '!' to reverse direction
  56. gamma_en_pin                                 0.19             # Pin for gamma enable
  57. gamma_current                                0.7              # Z stepper motor current
  58. gamma_max_rate                               600.0            # Maximum rate in mm/min
  59.  
  60. ## Extruder module configuration
  61. # See http://smoothieware.org/extruder
  62. extruder.hotend.enable                          true          # Whether to activate the extruder module at all. All configuration is ignored if false
  63. extruder.hotend.steps_per_mm                    842.9731      # Steps per mm for extruder stepper
  64. extruder.hotend.default_feed_rate               600           # Default rate ( mm/minute ) for moves where only the extruder moves
  65. extruder.hotend.acceleration                    500           # Acceleration for the stepper motor mm/sec²
  66. extruder.hotend.max_speed                       80            # Maximum speed in mm/s
  67.  
  68. extruder.hotend.step_pin                        2.3           # Pin for extruder step signal
  69. extruder.hotend.dir_pin                         0.22!         # Pin for extruder dir signal ( add '!' to reverse direction )
  70. extruder.hotend.en_pin                          0.21          # Pin for extruder enable signal
  71.  
  72. # Extruder offset
  73. #extruder.hotend.x_offset                        0            # X offset from origin in mm
  74. #extruder.hotend.y_offset                        0            # Y offset from origin in mm
  75. #extruder.hotend.z_offset                        0            # Z offset from origin in mm
  76.  
  77. # Firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
  78. #extruder.hotend.retract_length                  6            # Retract length in mm
  79. #extruder.hotend.retract_feedrate                45           # Retract feedrate in mm/sec
  80. #extruder.hotend.retract_recover_length          0            # Additional length for recover
  81. #extruder.hotend.retract_recover_feedrate        8            # Recover feedrate in mm/sec (should be less than retract feedrate)
  82. #extruder.hotend.retract_zlift_length            0            # Z-lift on retract in mm, 0 disables
  83. #extruder.hotend.retract_zlift_feedrate          6000         # Z-lift feedrate in mm/min (Note mm/min NOT mm/sec)
  84.  
  85. delta_current                                    1.0          # First extruder stepper motor current
  86.  
  87. # Second extruder module configuration
  88. #extruder.hotend2.enable                         true         # Whether to activate the extruder module at all. All configuration is ignored if false
  89. #extruder.hotend2.steps_per_mm                   192.915      # Steps per mm for extruder stepper
  90. #extruder.hotend2.default_feed_rate              600          # Default rate ( mm/minute ) for moves where only the extruder moves
  91. #extruder.hotend2.acceleration                   500          # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  92. #extruder.hotend2.max_speed                      50           # mm/s
  93.  
  94. #extruder.hotend2.step_pin                       2.8          # Pin for extruder step signal
  95. #extruder.hotend2.dir_pin                        2.13         # Pin for extruder dir signal ( add '!' to reverse direction )
  96. #extruder.hotend2.en_pin                         4.29         # Pin for extruder enable signal
  97.  
  98. #extruder.hotend2.x_offset                       0            # x offset from origin in mm
  99. #extruder.hotend2.y_offset                       25.0         # y offset from origin in mm
  100. #extruder.hotend2.z_offset                       0            # z offset from origin in mm
  101.  
  102. #epsilon_current                                 1.5          # Second extruder stepper motor current
  103.  
  104.  
  105. ## Laser module configuration
  106. # See http://smoothieware.org/laser
  107. laser_module_enable                           false           # Whether to activate the laser module at all
  108. laser_module_pwm_pin                          2.5             # This pin will be PWMed to control the laser.
  109.                                                               # Only pins 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 1.18, 1.20, 1.21, 1.23, 1.24, 1.26, 3.25 and 3.26
  110.                                                               # can be used since laser requires hardware PWM, see http://smoothieware.org/pinout
  111. #laser_module_ttl_pin                         1.30            # This pin turns on when the laser turns on, and off when the laser turns off.
  112. #laser_module_maximum_power                   1.0             # This is the maximum duty cycle that will be applied to the laser
  113. #laser_module_minimum_power                   0.0             # This is a value just below the minimum duty cycle that keeps the laser
  114.                                                               # active without actually burning.
  115. #laser_module_default_power                   0.8             # This is the default laser power that will be used for cuts if a power has not been specified.  The value is a scale between
  116.                                                               # the maximum and minimum power levels specified above
  117. #laser_module_pwm_period                      20              # This sets the pwm frequency as the period in microseconds
  118.  
  119. ## Temperature control configuration
  120. # See http://smoothieware.org/temperaturecontrol
  121.  
  122.  
  123. ############################
  124. # Heated bed configuration #
  125. ############################
  126.  
  127. temperature_control.bed.enable               true             # Whether to activate this ( "hotend" ) module at all.
  128. temperature_control.bed.thermistor_pin       0.23             # Pin for the thermistor to read
  129. temperature_control.bed.heater_pin           2.5              # Pin that controls the heater
  130. temperature_control.bed.thermistor           Semitec    # See http://smoothieware.org/temperaturecontrol#thermistor
  131. #temperature_control.bed.beta                3974             # Or set the beta value
  132. temperature_control.bed.set_m_code           140              # M-code to set the temperature for this module
  133. temperature_control.bed.set_and_wait_m_code  190              # M-code to set-and-wait for this module
  134. temperature_control.bed.designator           B                # Designator letter for this module
  135.  
  136. # Bang-bang ( simplified ) control
  137. # See http://smoothieware.org/temperaturecontrol#bang-bang
  138. #temperature_control.bed.bang_bang           false            # Set to true to use bang bang control rather than PID
  139. #temperature_control.bed.hysteresis          2.0              # Set to the temperature in degrees C to use as hysteresis
  140.  
  141. # PID bed configuration
  142. # See http://smoothieware.org/temperaturecontrol#pid
  143. temperature_control.bed.p_factor         34.4688              # P ( proportional ) factor
  144. temperature_control.bed.i_factor         0.7024               # I ( integral ) factor
  145. temperature_control.bed.d_factor         422.8896             # D ( derivative ) factor
  146.  
  147. temperature_control.bed.runaway_heating_timeout      900  # How long it can take to heat up, max is 2040 seconds.
  148. temperature_control.bed.runaway_cooling_timeout        0  # How long it can take to cool down if temp is set lower, max is 2040 seconds
  149. temperature_control.bed.runaway_range                63   # How far from the set temperature it can wander, max setting is 63°C
  150.  
  151.  
  152. ##############################
  153. # First hotend configuration #
  154. ##############################
  155.  
  156. temperature_control.hotend.enable            true             # Whether to activate this ( "hotend" ) module at all.
  157. temperature_control.hotend.thermistor_pin    0.24             # Pin for the thermistor to read
  158. temperature_control.hotend.heater_pin        2.7              # Pin that controls the heater, set to nc if a readonly thermistor is being defined
  159. temperature_control.hotend.thermistor        Semitec          # See http://smoothieware.org/temperaturecontrol#toc5
  160. #temperature_control.hotend.beta             4066             # Or set the beta value
  161. temperature_control.hotend.set_m_code        104              # M-code to set the temperature for this module
  162. temperature_control.hotend.set_and_wait_m_code 109            # M-code to set-and-wait for this module
  163. temperature_control.hotend.designator        T                # Designator letter for this module
  164. temperature_control.hotend.max_temp         300              # Set maximum temperature - Will prevent heating above 300 by default
  165. temperature_control.hotend.min_temp         0                # Set minimum temperature - Will prevent heating below if set
  166.  
  167. # Safety control is enabled by default and can be overidden here, the values show the defaults
  168. # See http://smoothieware.org/temperaturecontrol#runaway
  169. #temperature_control.hotend.runaway_heating_timeout      900  # How long it can take to heat up, max is 2040 seconds.
  170. #temperature_control.hotend.runaway_cooling_timeout        0  # How long it can take to cool down if temp is set lower, max is 2040 seconds
  171. #temperature_control.hotend.runaway_range                20   # How far from the set temperature it can wander, max setting is 63°C
  172.  
  173. # PID configuration
  174. # See http://smoothieware.org/temperaturecontrol#pid
  175. temperature_control.hotend.p_factor          50.6665          # P ( proportional ) factor
  176. temperature_control.hotend.i_factor          3.3721           # I ( integral ) factor
  177. temperature_control.hotend.d_factor          190.3161         # D ( derivative ) factor
  178.  
  179. #temperature_control.hotend.max_pwm          64               # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  180.  
  181.  
  182. ###############################
  183. # Second hotend configuration #
  184. ###############################
  185.  
  186. #temperature_control.hotend2.enable            true           # Whether to activate this ( "hotend" ) module at all.
  187. #temperature_control.hotend2.thermistor_pin    0.25           # Pin for the thermistor to read
  188. #temperature_control.hotend2.heater_pin        2.6            # Pin that controls the heater
  189. #temperature_control.hotend2.thermistor        Semitec        # See http://smoothieware.org/temperaturecontrol#thermistor
  190. ##temperature_control.hotend2.beta             4066           # or set the beta value
  191. #temperature_control.hotend2.set_m_code        104            # M-code to set the temperature for this module
  192. #temperature_control.hotend2.set_and_wait_m_code 109          # M-code to set-and-wait for this module
  193. #temperature_control.hotend2.designator        E2             # Designator letter for this module
  194.  
  195. #temperature_control.hotend2.p_factor          13.7           # P ( proportional ) factor
  196. #temperature_control.hotend2.i_factor          0.097          # I ( integral ) factor
  197. #temperature_control.hotend2.d_factor          24             # D ( derivative ) factor
  198.  
  199. #temperature_control.hotend2.max_pwm          64              # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  200.  
  201.  
  202.  
  203. ################################
  204. # Heated chamber configuration #
  205. ################################
  206.  
  207. ##temperature_control.chamber.enable               true             # Whether to activate this ( "hotend"; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
  208. panel.spi_cs_pin                             0.16              # SPI chip select     ; GLCD EXP1 Pin 4
  209. panel.encoder_a_pin                          3.25!^            # Encoder pin         ; GLCD EXP2 Pin 3
  210. panel.encoder_b_pin                          3.26!^            # Encoder pin         ; GLCD EXP2 Pin 5
  211. panel.click_button_pin                       1.30!^            # Click button        ; GLCD EXP1 Pin 2
  212. panel.buzz_pin                               1.31              # Pin for buzzer      ; GLCD EXP1 Pin 1
  213. #panel.back_button_pin                        2.11!^            # Back button         ; GLCD EXP2 Pin 8
  214.  
  215. panel.menu_offset                            0                 # Some panels will need 1 here
  216.  
  217. panel.alpha_jog_feedrate                     6000              # X jogging feedrate in mm/min
  218. panel.beta_jog_feedrate                      6000              # Y jogging feedrate in mm/min
  219. panel.gamma_jog_feedrate                     200               # Z jogging feedrate in mm/min
  220.  
  221. panel.hotend_temperature                     200               # Temp to set hotend when preheat is selected
  222. panel.bed_temperature                        100                # Temp to set bed when preheat is selected
  223.  
  224. ## Custom menus : Example of a custom menu entry, which will show up in the Custom entry.
  225. # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
  226.  
  227. custom_menu.tramming.enable                true             #
  228. custom_menu.tramming.name                  Tramming          #
  229. custom_menu.tramming.command               G32|G92_Z3.9               #
  230.  
  231. custom_menu.lights_on.enable               true             #
  232. custom_menu.lights_on.name                 Lights_on          #
  233. custom_menu.lights_on.command              M355               #
  234. custom_menu.lights_off.enable              true             #
  235. custom_menu.lights_off.name                Lights_off          #
  236. custom_menu.lights_off.command             M356               #
  237.  
  238. custom_menu.fan_on.enable                  true             #
  239. custom_menu.fan_on.name                    Fan_on          #
  240. custom_menu.fan_on.command                 M106               #
  241. custom_menu.fan_off.enable                 true             #
  242. custom_menu.fan_off.name                   Fan_off          #
  243. custom_menu.fan_off.command                M107               #
  244.  
  245. custom_menu.cfan_on.enable                 true             #
  246. custom_menu.cfan_on.name                   Chamber_fan_on          #
  247. custom_menu.cfan_on.command                M106.1               #
  248. custom_menu.cfan_off.enable                true             #
  249. custom_menu.cfan_off.name                  Chamber_fan_off          #
  250. custom_menu.cfan_off.command               M107.1               #
  251.  
  252. custom_menu.hfan_on.enable                 true             #
  253. custom_menu.hfan_on.name                   Hotend_fan_on          #
  254. custom_menu.hfan_on.command                M106.2               #
  255. custom_menu.hfan_off.enable                true             #
  256. custom_menu.hfan_off.name                  Hotend_fan_off          #
  257. custom_menu.hfan_off.command               M107.2               #
  258.  
  259. ## Network settings
  260. # See http://smoothieware.org/network
  261. network.enable                               false            # Enable the ethernet network services
  262. network.webserver.enable                     true             # Enable the webserver
  263. network.telnet.enable                        true             # Enable the telnet server
  264. network.ip_address                           auto             # Use dhcp to get ip address
  265. # Uncomment the 3 below to manually setup ip address
  266. #network.ip_address                           192.168.3.222   # The IP address
  267. #network.ip_mask                              255.255.255.0   # The ip mask
  268. #network.ip_gateway                           192.168.3.1     # The gateway address
  269. #network.mac_override                         xx.xx.xx.xx.xx.xx  # Override the mac address, only do this if you have a conflict
  270.  
  271. ## System configuration
  272. # Serial communications configuration ( baud rate defaults to 9600 if undefined )
  273. # For communication over the UART port, *not* the USB/Serial port
  274. uart0.baud_rate                              115200           # Baud rate for the default hardware ( UART ) serial port
  275.  
  276. second_usb_serial_enable                     false            # This enables a second USB serial port
  277. leds_disable                                 true             # Disable using leds after config loaded
  278. play_led_disable                             true             # Disable the play led
  279.  
  280. # Kill button maybe assigned to a different pin, set to the onboard pin by default
  281. # See http://smoothieware.org/killbutton
  282. kill_button_enable                           true             # Set to true to enable a kill button
  283. kill_button_pin                              2.12             # Kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
  284.  
  285. #msd_disable                                 false            # Disable the MSD (USB SDCARD), see http://smoothieware.org/troubleshooting#disable-msd
  286. #dfu_enable                                  false            # For linux developers, set to true to enable DFU
  287.  
  288. # Only needed on a smoothieboard
  289. # See http://smoothieware.org/currentcontrol
  290. currentcontrol_module_enable                 true             # Control stepper motor current via the configuration file
Advertisement
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!