iomega ix2-dl u-boot env help

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix2-nand ** ** uboot_ver:0.0.9 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Mar  7 2014 - 17:48:48) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:1024 MB
Found ADT7473, program PWM1 ... OK
Flash: 0 kb

Marvell Serial ATA Adapter
Integrated Sata device found


CPU : Marvell Feroceon (Rev 1)
Found kernel at 0x100000
Found initrd at 0x400000

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0


Marvell>> pri
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
kernel_size=0x300000
initrd_size=0x300000
loadzimage=nand read.e 0x40000 $(kernel_start) $(kernel_size)
loadinitrd=nand read.e 0x900000 $(initrd_start) $(initrd_size)
console=console=ttyS0,115200
bootargs_root=root=/dev/ram0
mk_mtdparts=setenv mtdparts mtdparts=nand_mtd:0x80000@0(uboot),0x20000@0xa0000(env),0x20000@0xc0000(env2),$(kernel_size)@$(kernel_start)(uImage),$(initrd_size)@$(initrd_start)(initrd),0x3f800000@0x800000(boot),1024m@0x0(flash)
initrdimage=mfginitrd
ipaddr=192.168.1.2
mfgmodel=ix2
preroot_ver=0.0.2
fw_ver=4.1.102.29716
serial_number=5563Y01011G43500778J0L1
ethaddr=00:D0:B8:15:8B:FA
serialNo=1S70A69003EAS10001EB
modelname=70A69003EA
serialno=1,01iyRyiT7s8jbZ52QpF8c5NG68///AJcIZxIJ8EAqmUz5NGZPlYLYzlRlbyKWRbwxT,1S70A69003EAS10001EB,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX2/1.1.0/download_runin.sh
pre_path_conf=IX2/1.1.0/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX2/1.1.0
serverip=192.168.32.4
bootcmd=run loadzimage; run loadinitrd; run mk_mtdparts; setenv bootargs $(console) $(bootargs_root) $(bootargs_end) $(mtdparts); bootm 0x40000 0x900000
uboot_ver=0.0.9
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
kernel_start=0x100000
initrd_start=0x400000
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no

Environment size: 2198/131067 bytes


Marvell>> help
?       - alias for 'help'
SatR - sample at reset sub-system, relevent for DB only
base    - print or set address offset
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootext2    dev:boot_part1,boot_part2 addr boot_image linux_dev_name
bootm   - boot application image from memory
bootp   - boot image via network using BootP/TFTP protocol
bubt    - Burn an image on the Boot Nand Flash.
chpart  - change active partition
cmp     - memory compare
cmpm    - Compare Memory
cp      - memory copy
cpumap - Display CPU memory mapping settings.
crc32   - checksum calculation
date    - get/set/reset date & time
dclk    - Display the MV device CLKs.
dhcp    - invoke DHCP client to obtain IP/boot params
diskboot- boot from IDE device
echo    - echo args to console
eeprom  - EEPROM sub-system
erase   - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fi      - Find value in the memory.
flinfo  - print FLASH memory information
fsinfo  - print information about filesystems
fsload  - load binary file from a filesystem image
g       - start application at cached address 'addr'(default addr 0x40000)
go      - start application at address 'addr'
help    - print online help
icrc32  - checksum calculation
ide     - IDE sub-system
iloop   - infinite loop on address range
imd     - i2c memory display
iminfo  - print header information for application image
imm[.b, .s, .w, .l]     - i2c memory modify (auto-incrementing)
imw     - memory write (fill)
inm     - memory modify (constant address)
iprobe  - probe to discover valid I2C chip addresses
ir      - reading and changing MV internal register values.
loop    - infinite loop on address range
ls      - list files in a directory (default /)
map     - Diasplay address decode windows
md      - memory display
me      - PCI master enable
mm      - memory modify (auto-incrementing)
mmcinit - init mmc card
mp      - map PCI BAR
mtdparts- define flash/nand partitions
mtest   - simple RAM test
mw      - memory write (fill)
nand                   - NAND sub-system
nboot   - boot from NAND device
nbubt   - Burn a boot loader image on the Boot Nand Flash.
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
phyRead - Read PCI-E Phy register
pciePhyWrite    - Write PCI-E Phy register
phyRead - Read Phy register
phyWrite        - Write Phy register
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
rcvr    - Satrt recovery process (Distress Beacon with TFTP server)
reset   - Perform RESET of the CPU
resetenv        - Return all environment variable to default.
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
se      - PCI Slave enable
setenv  - set environment variables
sflash  - read, write or erase the external SPI Flash.
sg      - scanning the PHYs status
sp      - Scan PCI bus.
switchRegRead   - Read switch register
switchRegWrite  - Write switch register
Temp    - read chip Tj temp
tftpboot- boot image via network using TFTP protocol
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor version