Advertisement
Guest User

rb953gs bootlog lede

a guest
Jan 8th, 2017
188
0
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 12.29 KB | None | 0 0
  1. RouterBOOT booter 3.29
  2.  
  3. RouterBoard 953GS-5HnT
  4.  
  5. CPU frequency: 720 MHz
  6. Memory speed: 300 MHz
  7. Memory size: 128 MiB
  8. NAND size: 128 MiB
  9.  
  10. Press any key within 2 seconds to enter setup
  11.  
  12. RouterBOOT-3.29
  13. What do you want to configure?
  14. d - boot delay
  15. k - boot key
  16. s - serial console
  17. n - silent boot
  18. o - boot device
  19. f - cpu frequency
  20. r - reset booter configuration
  21. e - format nand
  22. w - repartition nand
  23. g - upgrade firmware
  24. i - board info
  25. p - boot protocol
  26. b - booter options
  27. t - do memory testing
  28. x - exit setup
  29. your choice: s - serial console
  30.  
  31. Select baud rate for serial console:
  32. * 1 - 115200
  33. 2 - 57600
  34. 3 - 38400
  35. 4 - 19200
  36. 5 - 9600
  37. 6 - 4800
  38. 7 - 2400
  39. 8 - 1200
  40. 9 - off
  41. your choice: 1 - 115200
  42. press <Enter> key after changing baud rate... ok
  43.  
  44. RouterBOOT-3.29
  45. What do you want to configure?
  46. d - boot delay
  47. k - boot key
  48. s - serial console
  49. n - silent boot
  50. o - boot device
  51. f - cpu frequency
  52. r - reset booter configuration
  53. e - format nand
  54. w - repartition nand
  55. g - upgrade firmware
  56. i - board info
  57. p - boot protocol
  58. b - booter options
  59. t - do memory testing
  60. x - exit setup
  61. your choice: o - boot device
  62.  
  63. Select boot device:
  64. e - boot over Ethernet
  65. * n - boot from NAND, if fail then Ethernet
  66. 1 - boot Ethernet once, then NAND
  67. o - boot from NAND only
  68. b - boot chosen device
  69. f - boot Flash Configure Mode
  70. 3 - boot Flash Configure Mode once, then NAND
  71. your choice: 1 - boot Ethernet once, then NAND
  72.  
  73. RouterBOOT-3.29
  74. What do you want to configure?
  75. d - boot delay
  76. k - boot key
  77. s - serial console
  78. n - silent boot
  79. o - boot device
  80. f - cpu frequency
  81. r - reset booter configuration
  82. e - format nand
  83. w - repartition nand
  84. g - upgrade firmware
  85. i - board info
  86. p - boot protocol
  87. b - booter options
  88. t - do memory testing
  89. x - exit setup
  90. your choice: x - exit setup
  91.  
  92.  
  93. writing settings to flash...
  94.  
  95. RouterBOOT booter 3.29
  96.  
  97. RouterBoard 953GS-5HnT
  98.  
  99. CPU frequency: 720 MHz
  100. Memory speed: 300 MHz
  101. Memory size: 128 MiB
  102. NAND size: 128 MiB
  103.  
  104. Press any key within 2 seconds to enter setup..
  105. writing settings to flash... OK
  106. Please, check ethernet cable...
  107. trying bootp protocol.... OK
  108. Got IP address: 192.168.1.130
  109. resolved mac address xx:xx:xx:xx:xx:xx
  110. Gateway: 192.168.1.234
  111. transfer started ............................................. transfer ok, time=1.97s
  112. setting up elf image... OK
  113. jumping to kernel code
  114. [ 0.000000] Linux version 4.4.40 (gui@guipc) (gcc version 5.4.0 (LEDE GCC 5.4.0 r2815-621f8cbf) ) #0 Sat Jan 7 20:08:24 2017
  115. [ 0.000000] bootconsole [early0] enabled
  116. [ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
  117. [ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
  118. [ 0.000000] Determined physical RAM map:
  119. [ 0.000000] memory: 08000000 @ 00000000 (usable)
  120. [ 0.000000] User-defined physical RAM map:
  121. [ 0.000000] memory: 08000000 @ 00000000 (usable)
  122. [ 0.000000] Initrd not found or empty - disabling initrd
  123. [ 0.000000] No valid device tree found, continuing without
  124. [ 0.000000] Zone ranges:
  125. [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
  126. [ 0.000000] Movable zone start for each node
  127. [ 0.000000] Early memory node ranges
  128. [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
  129. [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
  130. [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  131. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  132. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
  133. [ 0.000000] Kernel command line: parts=1 boot_part_size=4194304 gpio=551549759 HZ=360000000 mem=128M kmac=00:0C:42:C6:61:1B board=953gs Board=953gs ver=3.29 hw_opt=00300204 boot=1 mlc=10 rootfstype=yaffs noinitrd console=ttyS0,115200
  134. [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
  135. [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  136. [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  137. [ 0.000000] Writing ErrCtl register=00000000
  138. [ 0.000000] Readback ErrCtl register=00000000
  139. [ 0.000000] Memory: 123484K/131072K available (2913K kernel code, 183K rwdata, 732K rodata, 1988K init, 195K bss, 7588K reserved, 0K cma-reserved)
  140. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  141. [ 0.000000] NR_IRQS:51
  142. [ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:240.000MHz, Ref:40.000MHz
  143. [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
  144. [ 0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
  145. [ 0.008670] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
  146. [ 0.071709] pid_max: default: 32768 minimum: 301
  147. [ 0.076946] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  148. [ 0.084315] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  149. [ 0.094235] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  150. [ 0.105750] NET: Registered protocol family 16
  151. [ 0.111970] MIPS: machine is MikroTik RouterBOARD 953GS-5HnT-RP
  152. [ 0.558948] registering PCI controller with io_map_base unset
  153. [ 0.565443] registering PCI controller with io_map_base unset
  154. [ 0.579694] PCI host bridge to bus 0000:00
  155. [ 0.584304] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
  156. [ 0.591960] pci_bus 0000:00: root bus resource [io 0x0000]
  157. [ 0.598167] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
  158. [ 0.605724] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
  159. [ 0.615005] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
  160. [ 0.623263] PCI host bridge to bus 0000:01
  161. [ 0.627851] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
  162. [ 0.635512] pci_bus 0000:01: root bus resource [io 0x0001]
  163. [ 0.641726] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
  164. [ 0.649283] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
  165. [ 0.658548] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x1200ffff 64bit]
  166. [ 0.666712] pci 0000:00:00.0: using irq 40 for pin 1
  167. [ 0.672262] pci 0000:01:00.0: using irq 41 for pin 1
  168. [ 0.678452] clocksource: Switched to clocksource MIPS
  169. [ 0.685111] NET: Registered protocol family 2
  170. [ 0.690605] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  171. [ 0.698375] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  172. [ 0.705500] TCP: Hash tables configured (established 1024 bind 1024)
  173. [ 0.712658] UDP hash table entries: 256 (order: 0, 4096 bytes)
  174. [ 0.719197] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  175. [ 0.726398] NET: Registered protocol family 1
  176. [ 2.492168] futex hash table entries: 256 (order: -1, 3072 bytes)
  177. [ 2.499088] Crashlog allocated RAM at address 0x3f00000
  178. [ 2.516105] io scheduler noop registered
  179. [ 2.520518] io scheduler deadline registered (default)
  180. [ 2.526464] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  181. [ 2.533909] console [ttyS0] disabled
  182. [ 2.557955] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
  183. [ 2.567573] console [ttyS0] enabled
  184. [ 2.567573] console [ttyS0] enabled
  185. [ 2.574991] bootconsole [early0] disabled
  186. [ 2.574991] bootconsole [early0] disabled
  187. [ 2.585750] m25p80 spi0.0: found w25x10, expected m25p80
  188. [ 2.591188] m25p80 spi0.0: w25x10 (128 Kbytes)
  189. [ 2.598241] nand: No NAND device found
  190. [ 2.602092] ar934x-nfc ar934x-nfc: nand_scan_ident failed, err:-19
  191. [ 2.618176] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
  192. [ 3.246142] libphy: ag71xx_mdio: probed
  193. [ 3.839953] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
  194. [ 3.851269] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
  195. [ 4.440035] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
  196. [ 4.447597] NET: Registered protocol family 10
  197. [ 4.455036] NET: Registered protocol family 17
  198. [ 4.459652] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
  199. [ 4.472558] 8021q: 802.1Q VLAN Support v1.8
  200. [ 4.476950] rb: no calibration data found
  201. [ 4.490314] Freeing unused kernel memory: 1988K (8041f000 - 80610000)
  202. [ 4.506034] init: Console is alive
  203. [ 4.509721] init: - watchdog -
  204. [ 4.533538] init: - preinit -
  205. [ 4.661672] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  206. Press the [f] key and hit [enter] to enter failsafe mode
  207. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  208. [ 5.839889] eth0: link up (1000Mbps/Full duplex)
  209. [ 5.844711] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  210. [ 7.776984] eth0: link down
  211. [ 7.787922] procd: - early -
  212. [ 7.791426] procd: - watchdog -
  213. [ 8.317507] procd: - ubus -
  214. [ 8.371496] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
  215. [ 8.380990] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
  216. [ 8.390155] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
  217. [ 8.399545] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
  218. [ 8.408704] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
  219. [ 8.417971] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
  220. [ 8.427261] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
  221. [ 8.436713] procd: - init -
  222. Please press Enter to activate this console.
  223. [ 8.565415] ip6_tables: (C) 2000-2006 Netfilter Core Team
  224. [ 8.579153] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
  225. [ 8.586833] Backport generated by backports.git backports-20160324-9-g0e38f5c
  226. [ 8.596375] ip_tables: (C) 2000-2006 Netfilter Core Team
  227. [ 8.607788] nf_conntrack version 0.5.0 (1960 buckets, 7840 max)
  228. [ 8.639178] xt_time: kernel timezone is -0000
  229. [ 8.687274] PPP generic driver version 2.4.2
  230. [ 8.693654] NET: Registered protocol family 24
  231. [ 8.735757] ath: phy0: Unable to initialize hardware; initialization status: -5
  232. [ 8.743196] ath9k qca955x_wmac: failed to initialize device
  233. [ 8.748882] ath9k: probe of qca955x_wmac failed with error -5
  234. [ 9.200935] ieee80211 phy1: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
  235. [ 9.653738] ieee80211 phy2: Atheros AR9280 Rev:2 mem=0xb2000000, irq=41
  236. [ 10.213404] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
  237. [ 10.276870] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
  238. [ 10.315076] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
  239. [ 14.926741] device eth0 entered promiscuous mode
  240. [ 14.954302] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  241. [ 15.009478] eth1: link up (1000Mbps/Full duplex)
  242. [ 15.670045] eth0: link up (1000Mbps/Full duplex)
  243. [ 15.674767] br-lan: port 1(eth0) entered forwarding state
  244. [ 15.680316] br-lan: port 1(eth0) entered forwarding state
  245. [ 15.771196] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  246. [ 17.678481] br-lan: port 1(eth0) entered forwarding state
  247.  
  248.  
  249.  
  250. BusyBox v1.25.1 () built-in shell (ash)
  251.  
  252. _________
  253. / /\ _ ___ ___ ___
  254. / LE / \ | | | __| \| __|
  255. / DE / \ | |__| _|| |) | _|
  256. /________/ LE \ |____|___|___/|___| lede-project.org
  257. \ \ DE /
  258. \ LE \ / -----------------------------------------------------------
  259. \ DE \ / Reboot (SNAPSHOT, r2815-621f8cbf)
  260. \________\/ -----------------------------------------------------------
  261.  
  262. === WARNING! =====================================
  263. There is no root password defined on this device!
  264. Use the "passwd" command to set up a new password
  265. in order to prevent unauthorized SSH logins.
  266. --------------------------------------------------
  267. root@lede:/# cat /proc/mtd
  268. dev: size erasesize name
  269. mtd0: 00020000 00001000 "spi0.0"
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement