Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- dmesg
- Copyright (c) 1992-2012 The FreeBSD Project.
- Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
- The Regents of the University of California. All rights reserved.
- FreeBSD is a registered trademark of The FreeBSD Foundation.
- FreeBSD 9.1-RELEASE #0: Wed Dec 5 22:23:59 UTC 2012
- root@anacreon.physics.wisc.edu:/usr/obj/usr/src/sys/GENERIC64 powerpc
- cpu0: IBM PowerPC 970FX revision 3.1, 2000.32 MHz
- cpu0: Features dc000000<PPC32,PPC64,ALTIVEC,FPU,MMU>
- cpu0: HID0 511081<NAP,DPM,NHR,TBEN,ENATTN>
- real memory = 4277223424 (4079 MB)
- avail memory = 4035497984 (3848 MB)
- FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
- cpu0: dev=ff899e08 (BSP)
- cpu1: dev=ff89b2e8
- kbd0 at kbdmux0
- nexus0: <Open Firmware Nexus device>
- cpulist0: <Open Firmware CPU Group> on nexus0
- cpu0: <Open Firmware CPU> on cpulist0
- pcr0: <PPC 970 Power Control Register> on cpu0
- pcr0: No power mode data in device tree!
- device_attach: pcr0 attach returned 6
- cpu1: <Open Firmware CPU> on cpulist0
- pcr1: <PPC 970 Power Control Register> on cpu1
- pcr1: No power mode data in device tree!
- device_attach: pcr1 attach returned 6
- powermac_nvram0: <Apple NVRAM> on nexus0
- powermac_nvram0: bank0 generation 506, bank1 generation 505
- unin0: <Apple UniNorth System Controller> on nexus0
- unin0: Set /u3/mpic as iparent!
- unin0: Version 55
- iichb0: <Keywest I2C controller> mem 0xf8001000-0xf8001fff irq 0 on unin0
- iicbus0: <OFW I2C bus> on iichb0
- iicbus0: <unknown card> at addr 0xd2
- ds17750: <Temp-Monitor DS1775> at addr 0x94 on iicbus0
- max66900: <Temp-Monitor MAX6690> at addr 0x98 on iicbus0
- iicbus0: <unknown card> at addr 0x96
- fcu0: <Apple Fan Control Unit> at addr 0x15e on iicbus0
- iicbus0: <unknown card> at addr 0x30
- ad74170: <Supply-Monitor AD7417> at addr 0x58 on iicbus0
- ad74170: 5 sensors detected.
- iicbus0: <unknown card> at addr 0xa0
- iicbus0: <unknown card> at addr 0x32
- ad74171: <Supply-Monitor AD7417> at addr 0x5a on iicbus0
- ad74171: 5 sensors detected.
- iicbus0: <unknown card> at addr 0xa2
- iicbus0: <unknown card> at addr 0x1c0
- htpic0: <OpenPIC Interrupt Controller> mem 0xf8040000-0xf807ffff irq 184 on unin0
- pcib0: <Apple U3 Host-AGP bridge> on nexus0
- pci0: <OFW PCI bus> on pcib0
- vgapci0: <VGA-compatible display> port 0x400-0x4ff mem 0x98000000-0x9fffffff,0x90000000-0x9000ffff irq 176 at device 16.0 on pci0
- agp0: <Apple U3 AGP Bridge> on hostb0
- pcib1: <IBM CPC9X5 HyperTransport Tunnel> on nexus0
- pcib1: 86 HT IRQs on device 1.0
- pci1: <OFW PCI bus> on pcib1
- pcib2: <OFW PCI-PCI bridge> at device 1.0 on pci1
- pci2: <OFW PCI bus> on pcib2
- macio0: <K2 KeyLargo I/O Controller> mem 0x80000000-0x8007ffff at device 7.0 on pci2
- openpic0: <OpenPIC Interrupt Controller> mem 0x40000-0x7ffff on macio0
- macgpio0: <MacIO GPIO Controller> mem 0x50-0x8a on macio0
- scc0: <Zilog Z8530 dual channel SCC> mem 0x13000-0x13fff,0x8400-0x84ff,0x8500-0x85ff,0x8600-0x86ff,0x8700-0x87ff irq 150,133,134,151,135,136 on macio0
- uart0: <z8530, channel A> on scc0
- uart1: <z8530, channel B> on scc0
- iichb1: <Keywest I2C controller> mem 0x18000-0x18fff irq 154 on macio0
- iicbus1: <OFW I2C bus> on iichb1
- iicbus1: <unknown card> at addr 0x1c0
- snapper0: <Texas Instruments TAS3004 Audio Codec> at addr 0x6a on iicbus1
- pcm0: <Apple I2S Audio Controller> mem 0-0xfff,0-0xff,0x100-0x1ff irq 158,129,130 on macio0
- macio0: failed to reserve resource 0 - 0x1000 (0x1000) for pcm0
- device_attach: pcm0 attach returned 6
- pmu0: <Apple PMU99 Controller> mem 0x16000-0x17fff irq 153 on macio0
- ohci0: <OHCI (generic) USB controller> mem 0x80081000-0x80081fff irq 155 at device 8.0 on pci2
- usbus0 on ohci0
- ohci1: <OHCI (generic) USB controller> mem 0x80080000-0x80080fff irq 156 at device 9.0 on pci2
- usbus1 on ohci1
- pcib3: <OFW PCI-PCI bridge> at device 2.0 on pci1
- pci3: <OFW PCI bus> on pcib3
- ohci2: <NEC uPD 9210 USB controller> mem 0x80702000-0x80702fff irq 191 at device 11.0 on pci3
- usbus2 on ohci2
- ohci3: <NEC uPD 9210 USB controller> mem 0x80701000-0x80701fff irq 191 at device 11.1 on pci3
- usbus3 on ohci3
- ehci0: <NEC uPD 720100 USB 2.0 controller> mem 0x80700000-0x807000ff irq 191 at device 11.2 on pci3
- usbus4: EHCI version 1.0
- usbus4 on ehci0
- pcib4: <OFW PCI-PCI bridge> at device 3.0 on pci1
- pci4: <OFW PCI bus> on pcib4
- ata0: <K2 Kauai ATA Controller> mem 0x80104000-0x80107fff irq 167 at device 13.0 on pci4
- fwohci0: <1394 Open Host Controller Interface> mem 0x80100000-0x80100fff irq 168 at device 14.0 on pci4
- fwohci0: OHCI version 1.0 (ROM=0)
- fwohci0: No. of Isochronous channels is 8.
- fwohci0: EUI64 00:11:24:ff:fe:86:68:ee
- fwohci0: invalid speed 7 (fixed to 3).
- fwohci0: Phy 1394a available S800, 3 ports.
- fwohci0: Link S800, max_rec 4096 bytes.
- firewire0: <IEEE1394(FireWire) bus> on fwohci0
- fwe0: <Ethernet over FireWire> on firewire0
- if_fwe0: Fake Ethernet address: 02:11:24:86:68:ee
- fwe0: Ethernet address: 02:11:24:86:68:ee
- sbp0: <SBP-2/SCSI over FireWire> on firewire0
- fwohci0: Initiate bus reset
- fwohci0: fwohci_intr_core: BUS reset
- fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=2, CYCLEMASTER mode
- pcib5: <OFW PCI-PCI bridge> at device 4.0 on pci1
- pci5: <OFW PCI bus> on pcib5
- gem0: <Apple K2 GMAC Ethernet> mem 0x80400000-0x805fffff irq 169 at device 15.0 on pci5
- miibus0: <MII bus> on gem0
- brgphy0: <BCM54K2 1000BASE-T media interface> PHY 1 on miibus0
- brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
- gem0: 10kB RX FIFO, 4kB TX FIFO
- gem0: Ethernet address: 00:11:24:86:68:ee
- pcib6: <OFW PCI-PCI bridge> at device 5.0 on pci1
- pci6: <OFW PCI bus> on pcib6
- atapci0: <ServerWorks K2 SATA150 controller> mem 0x80600000-0x80601fff irq 128 at device 12.0 on pci6
- pcib1: failed to reserve resource for pcib6
- atapci0: 0x10 bytes of rid 0x20 res 4 failed (0, 0xffffffffffffffff).
- ata2: <ATA channel> at channel 0 on atapci0
- ata3: <ATA channel> at channel 1 on atapci0
- ata4: <ATA channel> at channel 2 on atapci0
- ata5: <ATA channel> at channel 3 on atapci0
- atapci1: <ServerWorks K2 SATA150 controller> at device 12.1 on pci6
- pcib1: failed to reserve resource for pcib6
- atapci1: 0x10 bytes of rid 0x20 res 4 failed (0, 0xffffffffffffffff).
- atapci1: unable to map interrupt
- device_attach: atapci1 attach returned 6
- sc0: <System console> on nexus0
- sc0: Unknown <16 virtual consoles, flags=0x300>
- Timecounter "timebase" frequency 33333333 Hz quality 0
- Event timer "decrementer" frequency 33333333 Hz quality 1000
- Timecounters tick every 1.000 msec
- maxfirewire0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
- firewire0: bus manager 0
- 66900: 2 sensors detected.
- usbus0: 12Mbps Full Speed USB v1.0
- usbus1: 12Mbps Full Speed USB v1.0
- usbus2: 12Mbps Full Speed USB v1.0
- ugen0.1: <Apple> at usbus0
- uhub0: <Apple OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
- ugen1.1: <Apple> at usbus1
- uhub1: <Apple OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
- ugen2.1: <NEC> at usbus2
- uhub2: <NEC OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
- usbus3: 12Mbps Full Speed USB v1.0
- usbus4: 480Mbps High Speed USB v2.0
- ugen3.1: <NEC> at usbus3
- uhub3: <NEC OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
- ugen4.1: <NEC> at usbus4
- uhub4: <NEC EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
- uhub0: 2 ports with 2 removable, self powered
- uhub1: 2 ports with 2 removable, self powered
- uhub3: 2 ports with 2 removable, self powered
- uhub2: 3 ports with 3 removable, self powered
- fcu0: FCU initialized, RPM shift: 3
- fcu0: 7 fans detected!
- uhub4: 5 ports with 5 removable, self powered
- usb_alloc_device: set address 2 failed (USB_ERR_IOERROR, ignored)
- usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
- ada0 at ata2 bus 0 scbus2 target 0 lun 0
- ada0: <WDC WD1600AAJS-08L7A0 02.03E02> ATA-8 SATA 2.x device
- ada0: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
- ada0: 152627MB (312581808 512 byte sectors: 16H 63S/T 16383C)
- ada0: Previously was known as ad0
- ada1 at ata3 bus 0 scbus3 target 0 lun 0
- ada1: <WDC WD1600JD-41HBC0 21.02J21> ATA-6 SATA 1.x device
- ada1: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
- ada1: 152627MB (312581808 512 byte sectors: 16H 63S/T 16383C)
- ada1: Previously was known as ad1
- cd0 at ata0 bus 0 scbus0 target 0 lun 0
- cd0: <SONY DVD RW DW-Q28A KAS7> Removable CD-ROM SCSI-0 device
- cd0: 66.700MB/s transfers (UDMA4, ATAPI 12bytes, PIO 65534bytes)
- cd0: cd present [151744 x 2048 byte records]
- SMP: AP CPU #1 launched
- ugen2.2: <Macally Peripherals> at usbus2
- uhub5: <Macally Peripherals Hub in Macally ICEKEY keyboard, class 9/0, rev 1.10/1.58, addr 2> on usbus2
- uhub5: 3 ports with 2 removable, bus powered
- ugen2.3: <vendor 0x04b3> at usbus2
- ums0: <vendor 0x04b3 product 0x310d, class 0/0, rev 2.00/43.01, addr 3> on usbus2
- ums0: 3 buttons and [XYZ] coordinates ID=0
- ugen2.4: <Macally Peripherals> at usbus2
- ukbd0: <Macally Peripherals Macally ICEKey keyboard, class 0/0, rev 1.10/1.58, addr 4> on usbus2
- kbd1 at ukbd0
- uhid0: <Macally Peripherals Macally ICEKey keyboard, class 0/0, rev 1.10/1.58, addr 4> on usbus2
- GEOM_PART: integrity check failed (cd0, APM)
- GEOM_PART: integrity check failed (iso9660/NetBSD 6.1 macppccd, APM)
- Trying to mount root from ufs:/dev/ada0s3 [rw]...
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement