Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot SPL 2016.09.01-00003-g877b711 (Oct 06 2016 - 12:20:53)
- Setting 1024MB RAM calibration data
- Trying to boot from MMC1
- port 1
- U-Boot 2016.09.01-00003-g877b711 (Oct 06 2016 - 12:20:53 +0200)
- CPU: Freescale i.MX6SX rev1.2 at 792 MHz
- Reset cause: POR
- Board: UDOO Neo Extended
- I2C: ready
- DRAM: 1 GiB
- PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
- MMC: FSL_SDHC: 0, FSL_SDHC: 1
- *** Warning - bad CRC, using default environment
- In: serial
- Out: serial
- Err: serial
- Net: No ethernet found.
- Hit any key to stop autoboot: 0
- switch to partitions #0, OK
- mmc0 is current device
- reading uEnv.txt
- 163 bytes read in 10 ms (15.6 KiB/s)
- Running bootscript from mmc ...
- Device Tree: /boot/dts/imx6sx-udoo-neo-extended-hdmi-m4.dtb
- 4432800 bytes read in 270 ms (15.7 MiB/s)
- Booting from mmc ...
- 47321 bytes read in 191 ms (241.2 KiB/s)
- ## Flattened Device Tree blob at 83000000
- Booting using the fdt blob at 0x83000000
- Using Device Tree in place at 83000000, end 8300e8d8
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0
- [ 0.000000] Linux version 4.1.15-gfcea7a1-dirty (root@blackhole) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.1) ) #26 SMP PREEMPT Tue Sep 27 11:38:15 CEST 2016
- [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=50c53c7d
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000] Machine model: UDOO Neo Extended
- [ 0.000000] Reserved memory: created CMA memory pool at 0xaa000000, size 320 MiB
- [ 0.000000] Reserved memory: initialized node linux,cma, compatible id shared-dma-pool
- [ 0.000000] Memory policy: Data cache writealloc
- [ 0.000000] PERCPU: Embedded 11 pages/cpu @bf61c000 s16332 r8192 d20532 u45056
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257792
- [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw rootfstype=ext4 uart_from_osc clk_ignore_unused cpuidle.off=1 consoleblank=0
- [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
- [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Memory: 694640K/1039360K available (4179K kernel code, 262K rwdata, 2040K rodata, 208K init, 390K bss, 17040K reserved, 327680K cma-reserved, 0K highmem)
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
- [ 0.000000] vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
- [ 0.000000] lowmem : 0x80000000 - 0xc0000000 (1024 MB)
- [ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
- [ 0.000000] modules : 0x7f800000 - 0x7fe00000 ( 6 MB)
- [ 0.000000] .text : 0x80008000 - 0x8061b0f0 (6221 kB)
- [ 0.000000] .init : 0x8061c000 - 0x80650000 ( 208 kB)
- [ 0.000000] .data : 0x80650000 - 0x80691820 ( 263 kB)
- [ 0.000000] .bss : 0x80694000 - 0x806f585c ( 391 kB)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] Preemptible hierarchical RCU implementation.
- [ 0.000000] Additional per-CPU info printed with stalls.
- [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
- [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
- [ 0.000000] NR_IRQS:16 nr_irqs:16 16
- [ 0.000000] L2C-310 erratum 769419 enabled
- [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
- [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
- [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines
- [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
- [ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB
- [ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76430001
- [ 0.000000] mxc_clocksource_init 3000000
- [ 0.000000] Switching to timer-based delay loop, resolution 333ns
- [ 0.000006] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
- [ 0.000023] clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
- [ 0.001536] Console: colour dummy device 80x30
- [ 0.001553] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)
- [ 0.001567] pid_max: default: 32768 minimum: 301
- [ 0.001669] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.001683] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.002239] Initializing cgroup subsys devices
- [ 0.002260] Initializing cgroup subsys freezer
- [ 0.002288] CPU: Testing write buffer coherency: ok
- [ 0.002504] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
- [ 0.002569] Setting up static identity map for 0x80008240 - 0x8000828c
- [ 0.040419] Brought up 1 CPUs
- [ 0.040433] SMP: Total of 1 processors activated (6.00 BogoMIPS).
- [ 0.040443] CPU: All CPU(s) started in SVC mode.
- [ 0.040874] devtmpfs: initialized
- [ 0.050630] device-tree: Duplicate name in lcdif@02220000, renamed to "display#1"
- [ 0.054507] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
- [ 0.054895] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.073827] pinctrl core: initialized pinctrl subsystem
- [ 0.074968] NET: Registered protocol family 16
- [ 0.083754] DMA: preallocated 256 KiB pool for atomic coherent allocations
- [ 0.091269] GPIO mask to reserved irq for M4 Core = 0x00000350
- [ 0.091990] GPIO mask to reserved irq for M4 Core = 0x003cf000
- [ 0.092696] GPIO mask to reserved irq for M4 Core = 0x000c0000
- [ 0.110237] imx6sx-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
- [ 0.112214] MU is ready for cross core communication!
- [ 0.123712] mxs-dma 1804000.dma-apbh: initialized
- [ 0.127280] SCSI subsystem initialized
- [ 0.127875] 2000000.aips-bus:usbphy_nop1 supply vcc not found, using dummy regulator
- [ 0.128954] i2c i2c-0: IMX I2C adapter registered
- [ 0.128974] i2c i2c-0: can't use DMA
- [ 0.129806] i2c i2c-1: IMX I2C adapter registered
- [ 0.129824] i2c i2c-1: can't use DMA
- [ 0.130340] i2c i2c-2: IMX I2C adapter registered
- [ 0.130358] i2c i2c-2: can't use DMA
- [ 0.131173] i2c i2c-3: IMX I2C adapter registered
- [ 0.131191] i2c i2c-3: can't use DMA
- [ 0.131328] Linux video capture interface: v2.00
- [ 0.131387] pps_core: LinuxPPS API ver. 1 registered
- [ 0.131396] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 0.131437] PTP clock support registered
- [ 0.132901] Advanced Linux Sound Architecture Driver Initialized.
- [ 0.134850] Switched to clocksource mxc_timer1
- [ 0.146331] NET: Registered protocol family 2
- [ 0.146971] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.147060] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
- [ 0.147184] TCP: Hash tables configured (established 8192 bind 8192)
- [ 0.147263] UDP hash table entries: 512 (order: 2, 16384 bytes)
- [ 0.147301] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
- [ 0.147507] NET: Registered protocol family 1
- [ 0.148116] imx rpmsg driver is registered.
- [ 0.149297] Bus freq driver module loaded
- [ 0.150312] futex hash table entries: 256 (order: 2, 16384 bytes)
- [ 0.157801] VFS: Disk quotas dquot_6.6.0
- [ 0.158023] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 0.163801] io scheduler noop registered
- [ 0.163825] io scheduler deadline registered
- [ 0.164042] io scheduler cfq registered (default)
- [ 0.164578] imx-weim 21b8000.weim: Driver registered.
- [ 0.165957] MIPI DSI driver module loaded
- [ 0.166202] MIPI DSI driver module loaded
- [ 0.295783] tda19988 2-0034: Sucessfully initialised chip revision 301
- [ 0.403077] mxsfb 2220000.lcdif: failed to find mxc display driver
- [ 0.423571] Console: switching to colour frame buffer device 160x45
- [ 0.469545] tda19988 2-0034: Matching CEA mode is 4 for fb mode 1280x720-60
- [ 0.522120] mxsfb 2220000.lcdif: initialized
- [ 0.525367] imx-sdma 20ec000.sdma: no iram assigned, using external mem
- [ 0.527171] imx-sdma 20ec000.sdma: no event needs to be remapped
- [ 0.528174] imx-sdma 20ec000.sdma: loaded firmware 3.3
- [ 0.531456] imx-sdma 20ec000.sdma: initialized
- [ 0.533193] pfuze100-regulator 0-0008: Full layer: 1, Metal layer: 1
- [ 0.533767] pfuze100-regulator 0-0008: FAB: 0, FIN: 0
- [ 0.533781] pfuze100-regulator 0-0008: pfuze3000 found.
- [ 0.547064] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 22, base_baud = 1500000) is a IMX
- [ 1.232131] console [ttymxc0] enabled
- [ 1.236757] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 283, base_baud = 1500000) is a IMX
- [ 1.248157] imx sema4 driver is registered.
- [ 1.252422] [drm] Initialized drm 1.1.0 20060810
- [ 1.257633] [drm] Initialized vivante 1.0.0 20120216 on minor 0
- [ 1.269622] loop: module loaded
- [ 1.274031] input: fxos8700 as /devices/soc0/soc/2100000.aips-bus/21f8000.i2c/i2c-3/3-001e/input/input0
- [ 1.285565] fxos8700 device driver probe successfully
- [ 1.291574] input: fxas2100x as /devices/soc0/soc/2100000.aips-bus/21f8000.i2c/i2c-3/3-0020/input/input1
- [ 1.301740] fxas2100x 3-0020: fxas2100x device driver probe successfully
- [ 1.312544] mousedev: PS/2 mouse device common for all mice
- [ 1.319738] read mpl3115 chip id 0xfffffffb
- [ 1.323941] mpl3115 1-0060: read chip ID 0x1 is not equal to 0xc4!
- [ 1.330204] mpl3115: probe of 1-0060 failed with error -22
- [ 1.336377] i2c /dev entries driver
- [ 1.341720] pxp-v4l2 pxp_v4l2_out: initialized
- [ 1.348492] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
- [ 1.354953] sdhci: Secure Digital Host Controller Interface driver
- [ 1.361146] sdhci: Copyright(c) Pierre Ossman
- [ 1.365544] sdhci-pltfm: SDHCI platform and OF driver helper
- [ 1.372387] /soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified
- [ 1.379611] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO
- [ 1.385944] sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found
- [ 1.435100] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
- [ 1.446002] /soc/aips-bus@02100000/usdhc@02198000: voltage-ranges unspecified
- [ 1.458268] sdhci-esdhc-imx 2198000.usdhc: could not get ultra high speed state, work on normal mode
- [ 1.472646] sdhci-esdhc-imx 2198000.usdhc: No vqmmc regulator found
- [ 1.522470] mmc0: host does not support reading read-only switch, assuming write-enable
- [ 1.536532] mmc0: new high speed SDHC card at address 59b4
- [ 1.542437] mmcblk0: mmc0:59b4 NCard 29.5 GiB
- [ 1.548222] mmcblk0: p1 p2
- [ 1.594926] mmc2: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
- [ 1.611851] galcore: clk_get 2d core clock failed, disable 2d/vg!
- [ 1.621304] Galcore version 5.0.11.41671
- [ 1.627691] sdhci-esdhc-imx 2198000.usdhc: card claims to support voltages below defined range
- [ 1.667207] mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
- [ 1.686209] mmc2: new high speed SDIO card at address 0001
- [ 1.941400] caam 2100000.caam: Entropy delay = 3200
- [ 2.067889] caam 2100000.caam: Entropy delay = 3600
- [ 2.141132] caam 2100000.caam: Instantiated RNG4 SH0
- [ 2.277809] caam 2100000.caam: Entropy delay = 4000
- [ 2.434539] caam 2100000.caam: Instantiated RNG4 SH1
- [ 2.439532] caam 2100000.caam: device ID = 0x0a16010000000200 (Era -524)
- [ 2.446260] caam 2100000.caam: job rings = 2, qi = 0
- [ 2.510880] caam algorithms registered in /proc/crypto
- [ 2.520171] caam_jr 2101000.jr0: registering rng-caam
- [ 2.525631] snvs-secvio 20cc000.caam-snvs: can't get snvs clock
- [ 2.531620] snvs-secvio 20cc000.caam-snvs: violation handlers armed - non-secure state
- [ 2.543338] fsl-asrc 2034000.asrc: driver registered
- [ 2.553430] imx-tda19988 sound: tda19988-codec <-> 202c000.ssi mapping ok
- [ 2.561164] nf_conntrack version 0.5.0 (15973 buckets, 63892 max)
- [ 2.568082] NET: Registered protocol family 17
- [ 2.572589] Key type dns_resolver registered
- [ 2.577667] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
- [ 2.604863] failed to register cpuidle driver
- [ 2.609246] ThumbEE CPU extension supported.
- [ 2.616333] hctosys: unable to open rtc device (rtc0)
- [ 2.632552] VLDO2: disabling
- [ 2.636015] wlan-en-regulator: disabling
- [ 2.639947] vref-3v3: disabling
- [ 2.643092] PSU-5V0: disabling
- [ 2.646386] usb_otg2_vbus: disabling
- [ 2.649997] usb_otg1_vbus: disabling
- [ 2.653603] vddpcie-phy: disabling
- [ 2.657121] clk: Not disabling unused clocks
- [ 2.661404] ALSA device list:
- [ 2.664377] #0: imx-audio-tda19988
- [ 3.508531] EXT4-fs (mmcblk0p2): recovery complete
- [ 3.517712] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
- [ 3.526060] VFS: Mounted root (ext4 filesystem) on device 179:2.
- [ 3.532398] devtmpfs: mounted
- [ 3.536303] Freeing unused kernel memory: 208K (8061c000 - 80650000)
- [ 4.010832] systemd[1]: System time before build time, advancing clock.
- [ 4.067578] NET: Registered protocol family 10
- [ 4.103415] random: systemd urandom read with 36 bits of entropy available
- [ 4.113383] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
- [ 4.132117] systemd[1]: Detected architecture arm.
- Welcome to Ubuntu 16.04.1 LTS!
- [ 4.176009] systemd[1]: Set hostname to <udooneo>.
- [ 4.706352] systemd[1]: Listening on udev Control Socket.
- [ OK ] Listening on udev Control Socket.
- [ 4.735222] systemd[1]: Listening on udev Kernel Socket.
- [ OK ] Listening on udev Kernel Socket.
- [ 4.755233] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
- [ OK ] Listening on /dev/initctl Compatibility Named Pipe.
- [ 4.785712] systemd[1]: Listening on Journal Socket.
- [ OK ] Listening on Journal Socket.
- [ 4.805356] systemd[1]: Reached target Swap.
- [ OK ] Reached target Swap.
- [ 4.825659] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
- [ OK ] Started Forward Password Requests to Wall Directory Watch.
- [ 4.855516] systemd[1]: Listening on Journal Socket (/dev/log).
- [ OK ] Listening on Journal Socket (/dev/log).
- [ 4.875251] systemd[1]: Reached target Remote File Systems (Pre).
- [ OK ] Reached target Remote File Systems (Pre).
- [ 4.895211] systemd[1]: Reached target Remote File Systems.
- [ OK ] Reached target Remote File Systems.
- [ 4.916566] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
- [ OK ] Set up automount Arbitrary Executab...ats File System Automount Point.
- [ 4.945279] systemd[1]: Reached target User and Group Name Lookups.
- [ OK ] Reached target User and Group Name Lookups.
- [ 4.977112] systemd[1]: Created slice System Slice.
- [ OK ] Created slice System Slice.
- [ 5.007117] systemd[1]: Mounting Debug File System...
- Mounting Debug File System...
- [ 5.037249] systemd[1]: Starting Remount Root and Kernel File Systems...
- Starting Remount Root and Kernel File Systems...
- [ 5.080793] systemd[1]: Starting Create list of required static device nodes for the current kernel...
- Starting Create list of required st... nodes for the current kernel...
- [ 5.137482] systemd[1]: Starting Set console keymap...
- Starting Set console keymap...
- [ 5.152528] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
- [ 5.160672] systemd[1]: Created slice system-serial\x2dgetty.slice.
- [ OK ] Created slice system-serial\x2dgetty.slice.
- [ 5.185140] systemd[1]: Reached target Encrypted Volumes.
- [ OK ] Reached target Encrypted Volumes.
- [ 5.225285] systemd[1]: Listening on Syslog Socket.
- [ OK ] Listening on Syslog Socket.
- [ 5.246987] systemd[1]: Starting Journal Service...
- Starting Journal Service...
- [ 5.266567] systemd[1]: Created slice User and Session Slice.
- [ OK ] Created slice User and Session Slice.
- [ 5.285357] systemd[1]: Reached target Slices.
- [ OK ] Reached target Slices.
- [ 5.309878] systemd[1]: Starting Load Kernel Modules...
- Starting Load Kernel Modules...
- [ 5.356726] systemd[1]: Starting Nameserver information manager...
- Starting Nameserver information manager...
- [ 5.404154] systemd[1]: Mounted Debug File System.
- [ OK ] Mounted Debug File System.
- [ 5.436481] systemd[1]: Started Remount Root and Kernel File Systems.
- [ OK ] Started Remount Root and Kernel File Systems.
- [ 5.485315] systemd[1]: Started Create list of required static device nodes for the current kernel.
- [ OK ] Started Create list of required sta...ce nodes for the current kernel.
- [ 5.506124] systemd[1]: Started Set console keymap.
- [ OK ] Started Set console keymap.
- [ 5.526335] systemd[1]: Started Load Kernel Modules.
- [ OK ] Started Load Kernel Modules.
- [ 5.553940] systemd[1]: Started Journal Service.
- [ OK ] Started Journal Service.
- [ OK ] Started Nameserver information manager.
- Starting Apply Kernel Variables...
- Starting Create Static Device Nodes in /dev...
- Starting udev Coldplug all Devices...
- Starting Flush Journal to Persistent Storage...
- Starting Load/Save Random Seed...
- [ OK ] Started Apply Kernel Variables.
- [ OK ] Started Load/Save Random Seed.
- [ OK ] Started Create Static Device Nodes in /dev.
- [ OK ] Started Flush Journal to Persistent Storage.
- [ OK ] Reached target Local File Systems (Pre).
- Starting udev Kernel Device Manager...
- [ OK ] Started udev Coldplug all Devices.
- [ OK ] Started udev Kernel Device Manager.
- [ OK ] Started Dispatch Password Requests to Console Directory Watch.
- [ OK ] Found device /dev/ttymxc0.
- [ OK ] Found device /dev/mmcblk0p1.
- Mounting /otgstorage...
- [ OK ] Mounted /otgstorage.
- [ OK ] Reached target Sound Card.
- [ OK ] Reached target Local File Systems.
- Starting Create Volatile Files and Directories...
- Starting Set console font and keymap...
- Starting Raise network interfaces...
- [ 8.034922] (stk) :ldisc installation timeout
- Starting Tell Plymouth To Write Out Runtime Data...
- [ OK ] Started Tell Plymouth To Write Out Runtime Data.
- [ OK ] Started Create Volatile Files and Directories.
- [ OK ] Reached target System Time Synchronized.
- Starting Update UTMP about System Boot/Shutdown...
- [ 9.034940] (stk) : timed out waiting for ldisc to be un-installed
- [ OK ] Started Set console font and keymap.
- [ OK ] Created slice system-getty.slice.
- [ OK ] Started Update UTMP about System Boot/Shutdown.
- [ OK ] Reached target System Initialization.
- [ OK ] Started Daily apt activities.
- [ OK ] Started Daily Cleanup of Temporary Directories.
- [ OK ] Reached target Timers.
- [ OK ] Listening on D-Bus System Message Bus Socket.
- [ OK ] Started Trigger resolvconf update for networkd DNS.
- [ OK ] Reached target Paths.
- [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
- [ OK ] Reached target Sockets.
- [ OK ] Reached target Basic System.
- [ OK ] Started Run anacron jobs.
- [ OK ] Started Regular background program processing daemon.
- [ OK ] Started UDOO Sensors and GPIOs exporter.
- [ OK ] Started Cgroup management daemon.
- Starting LSB: setting xorg.conf...
- Starting Login Service...
- [ OK ] Started D-Bus System Message Bus.
- [ 10.145763] (stk) :ldisc installation timeout
- Starting autohdmi.service...
- Starting System Logging Service...
- Starting Avahi mDNS/DNS-SD Stack...
- Starting Permit User Sessions...
- Starting UDOO Neo Bluetooth Stack...
- Starting LSB: Load kernel modules needed to enable cpufreq scaling...
- [ OK ] Started UDOO Web Configuration Tool.
- Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"...
- Starting Accounts Service...
- Starting Network Manager...
- Starting Save/Restore Sound Card State...
- (stk) : timed out waiting for ldisc to be un-installed
- [ OK ] Started System Logging Service.
- [ OK ] Started Permit User Sessions.
- [ 11.344943] misc FreescaleGyroscope: mma enable setting active
- [ OK ] Started Save/Restore Sound Card State.
- [ OK ] Started LSB: setting xorg.conf.
- [ OK ] Started autohdmi.service.
- [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand".
- [ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling.
- [ OK ] Started Raise network interfaces.
- [ OK ] Started Avahi mDNS/DNS-SD Stack.
- [ OK ] Started Network Manager.
- [ OK ] Started Login Service.
- Starting Network Manager Script Dispatcher Service...
- Starting Authenticate and Authorize Users to Run Privileged Tasks...
- [ OK ] Reached target Network.
- Starting OpenBSD Secure Shell server...
- [ OK ] Reached target Network is Online.
- [ OK ] Started ISC DHCP IPv4 server.
- Starting /etc/rc.local Compatibility...
- Starting LSB: Advanced IEEE 802.11 management daemon...
- Starting LSB: Start NTP daemon...
- Starting LSB: set CPUFreq kernel parameters...
- Starting Light Display Manager...
- [ OK ] Started /etc/rc.local Compatibility.
- [ OK ] Started LSB: Advanced IEEE 802.11 management daemon.
- [ OK ] Started OpenBSD Secure Shell server.
- [ OK ] Started Network Manager Script Dispatcher Service.
- Starting Hostname Service...
- Starting Hold until boot process finishes up...
- [ OK ] Started LSB: set CPUFreq kernel parameters.
- [ OK ] Started Hold until boot process finishes up.
- [ OK ] Started Authenticate and Authorize Users to Run Privileged Tasks.
- [ OK ] Started LSB: Start NTP daemon.
- [ OK ] Started Accounts Service.
- [ OK ] Started Hostname Service.
- [ OK ] Started Serial Getty on ttymxc0.
- Starting Set console scheme...
- [ OK ] Started Getty on tty1.
- [ OK ] Reached target Login Prompts.
- Starting LSB: Set sysfs variables from /etc/sysfs.conf...
- [ OK ] Started Set console scheme.
- [ OK ] Started Light Display Manager.
- [ OK ] Started LSB: Set sysfs variables from /etc/sysfs.conf.
- Starting Bluetooth service...
- [ OK ] Started Bluetooth service.
- [ OK ] Reached target Bluetooth.
- [ OK ] Created slice User Slice of udooer.
- [ OK ] Started Session c1 of user udooer.
- Starting User Manager for UID 1000...
- [ OK ] Started User Manager for UID 1000.
- UDOObuntu v3.0 Alpha2
- default username:password is [udooer:udooer]
- udooneo login:
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement