loic@loic-laptop:~$ xrandr -s 1024x768
loic@loic-laptop:~$ cat /var/log/Xorg.0.log | grep CHROME
(II) OPENCHROME: Driver for VIA Chrome chipsets: CLE266, KM400/KN400,
(II) CHROME(0): VIAPreInit
(II) CHROME(0): VIAGetRec
(II) CHROME(0): Creating default Display subsection in Screen section
(==) CHROME(0): Depth 24, (--) framebuffer bpp 32
(==) CHROME(0): RGB weight 888
(==) CHROME(0): Default visual is TrueColor
(--) CHROME(0): Chipset: K8M800/K8N800
(--) CHROME(0): Chipset revision: 0
(--) CHROME(0): Probed amount of VideoRAM = 65536 kB
(II) CHROME(0): Setting up default chipset options.
(II) CHROME(0): VIASetupDefaultOptions
(II) CHROME(0): Reading config file...
(**) CHROME(0): Option "PanelSize" "1024x768"
(II) CHROME(0): Starting to parse config file options...
(==) CHROME(0): Shadow framebuffer is disabled.
(==) CHROME(0): Hardware acceleration is enabled.
(==) CHROME(0): Using XAA acceleration architecture.
(==) CHROME(0): Using hardware two-color cursors and software full-color cursors.
(==) CHROME(0): GPU virtual command queue will be enabled.
(==) CHROME(0): DRI IRQ will be disabled if DRI is enabled.
(==) CHROME(0): AGP DMA will be enabled if DRI is enabled.
(==) CHROME(0): AGP DMA will be used for 2D acceleration.
(==) CHROME(0): PCI DMA will be used for XV image transfer if DRI is enabled.
(==) CHROME(0): Will not enable VBE modes.
(==) CHROME(0): VBE VGA register save & restore will not be used
(==) CHROME(0): Xv Bandwidth check is enabled.
(==) CHROME(0): Will not impose a limit on video RAM reserved for DRI.
(==) CHROME(0): Will try to allocate 32768 kB of AGP memory.
(==) CHROME(0): Digital output bus width is 12 bits.
(==) CHROME(0): DVI Center is disabled.
(II) CHROME(0): ViaPanelGetNativeModeFromOption
(**) CHROME(0): Panel mode index is 2
(**) CHROME(0): Selected Panel Size is 1024x768
(==) CHROME(0): Panel will not be forced.
(==) CHROME(0): TV dotCrawl is disabled.
(==) CHROME(0): TV deflicker is set to 0.
(==) CHROME(0): No default TV type is set.
(==) CHROME(0): No default TV output signal type is set.
(==) CHROME(0): No default TV output port is set.
(II) CHROME(0): VIAMapMMIO
(--) CHROME(0): mapping MMIO @ 0xe1000000 with size 0x9000
(--) CHROME(0): mapping BitBlt MMIO @ 0xe1200000 with size 0x200000
(II) CHROME(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(==) CHROME(0): Will not print VGA registers.
(==) CHROME(0): Will not scan I2C buses.
(II) CHROME(0): ...Finished parsing config file options.
(--) CHROME(0): Detected Packard Bell Easynote E6116/E63xx. Card-Ids (1631|C008)
(II) CHROME(0): Detected MemClk 5
(II) CHROME(0): ViaGetMemoryBandwidth. Memory type: 5
(II) CHROME(0): Detected TV standard: PAL.
(==) CHROME(0): Using gamma correction (1.0, 1.0, 1.0)
(II) CHROME(0): ViaI2CInit
(II) CHROME(0): ViaI2CBus1Init
(II) CHROME(0): I2C bus "I2C bus 1" initialized.
(II) CHROME(0): ViaI2cBus2Init
(II) CHROME(0): I2C bus "I2C bus 2" initialized.
(II) CHROME(0): ViaI2CBus3Init
(II) CHROME(0): I2C bus "I2C bus 3" initialized.
(II) CHROME(0): I2C device "I2C bus 1:ddc2" registered at address 0xA0.
(II) CHROME(0): ViaOutputsDetect
(II) CHROME(0): Enabling panel from PCI-subsystem ID information.
(II) CHROME(0): VIATVDetect
(II) CHROME(0): ViaVT162xDetect
(II) CHROME(0): I2C device "I2C bus 3:VT162x" registered at address 0x40.
(--) CHROME(0): Detected VIA Technologies VT1622A/VT1623 TV Encoder
(II) CHROME(0): ViaTVInit
(II) CHROME(0): ViaVT162xInit
(II) CHROME(0): VT162xSave
(II) CHROME(0): VT1622DACSense
(--) CHROME(0): VT162x: Nothing connected.
(II) CHROME(0): ViaOutputsSelect
(II) CHROME(0): ViaOutputsSelect: X Configuration: 0x00
(II) CHROME(0): ViaOutputsSelect: BIOS Initialised register: 0x01
(II) CHROME(0): ViaOutputsSelect: Panel.
(WW) CHROME(0): Panel on K8M800 and VM800 is currently not supported.
(WW) CHROME(0): Using VBE to set modes to work around this.
(II) CHROME(0): initializing int10
(II) CHROME(0): Bad V_BIOS checksum
(II) CHROME(0): Primary V_BIOS segment is: 0xc000
(II) CHROME(0): VESA BIOS detected
(II) CHROME(0): VESA VBE Version 3.0
(II) CHROME(0): VESA VBE Total Mem: 65536 kB
(II) CHROME(0): VESA VBE OEM: VIA K8N800
(II) CHROME(0): VESA VBE OEM Software Rev: 1.0
(II) CHROME(0): VESA VBE OEM Vendor:
(II) CHROME(0): VESA VBE OEM Product:
(II) CHROME(0): VESA VBE OEM Product Rev:
(II) CHROME(0): Searching for matching VESA mode(s):
(II) CHROME(0): LCD: Using default hsync range of 31.50-37.90 kHz
(II) CHROME(0): LCD: Using default vrefresh range of 50.00-70.00 Hz
(WW) CHROME(0): Unable to estimate virtual size
(II) CHROME(0): Attempting to use 60Hz refresh for mode "800x600" (115)
(II) CHROME(0): Attempting to use 60Hz refresh for mode "640x480" (112)
(--) CHROME(0): Virtual size is 1600x1200 (pitch 1600)
(**) CHROME(0): *Built-in mode "1600x1200"
(**) CHROME(0): *Built-in mode "1400x1050"
(**) CHROME(0): *Built-in mode "1280x1024"
(**) CHROME(0): *Built-in mode "1280x768"
(**) CHROME(0): *Built-in mode "1024x768"
(**) CHROME(0): *Built-in mode "800x600": 0.0 MHz, 37879.3 kHz, 60.8 Hz
(II) CHROME(0): Modeline "800x600"x60.8    0.00  800 0 0 0  600 0 0 0 (37879.3 kHz)
(**) CHROME(0): *Built-in mode "640x480": 0.0 MHz, 31469.2 kHz, 60.4 Hz
(II) CHROME(0): Modeline "640x480"x60.4    0.00  640 0 0 0  480 0 0 0 (31469.2 kHz)
(==) CHROME(0): DPI set to (96, 96)
(II) CHROME(0): VIAUnmapMem
(II) CHROME(0): VIAScreenInit
(II) CHROME(0): VIAMapFB
(--) CHROME(0): mapping framebuffer @ 0xa4000000 with size 0x4000000
(--) CHROME(0): Frame buffer start: 0xb346e000, free start: 0x753000 end: 0x4000000
(II) CHROME(0): VIAMapMMIO
(--) CHROME(0): mapping MMIO @ 0xe1000000 with size 0x9000
(--) CHROME(0): mapping BitBlt MMIO @ 0xe1200000 with size 0x200000
(II) CHROME(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) CHROME(0): VIASave
(II) CHROME(0): Primary
(II) CHROME(0): Primary Adapter! saving VGA_SR_ALL !!
(II) CHROME(0): Non-Primary Adapter! saving VGA_SR_MODE only !!
(II) CHROME(0): Crtc...
(II) CHROME(0): TVSave...
(II) CHROME(0): VT162xSave
(WW) CHROME(0): Unable to determine the refresh rate, using 60.00. Please check your configuration.
(II) CHROME(0): Trying VBE Mode 1600x1200 (0xc124) Refresh 60.00:
(II) CHROME(0): ViaVbeSetRefresh
(II) CHROME(0): Active Device: 2
(II) CHROME(0): Refresh Rate Index: 0
(II) CHROME(0): VIAAdjustFrame 0x0
(II) CHROME(0): - Blanked
(II) CHROME(0): [drm] Using the DRM lock SAREA also for drawables.
(II) CHROME(0): [drm] framebuffer handle = 0xa4000000
(II) CHROME(0): [drm] added 1 reserved context for kernel
(II) CHROME(0): X context handle = 0x1
(II) CHROME(0): [drm] installed DRM signal handler
(II) CHROME(0): [dri] visual configs initialized.
(II) CHROME(0): [drm] register handle = 0xe1000000
(II) CHROME(0): [drm] framebuffer handle = 0xa4000000
(II) CHROME(0): [drm] mmio Registers = 0xe1000000
(II) CHROME(0): [dri] mmio mapped.
(II) CHROME(0): - Visuals set up
(II) CHROME(0): VIAInternalScreenInit
(II) CHROME(0): - B & W
(II) CHROME(0): CursorStart: 0x3fc0000
(II) CHROME(0): Frame Buffer From (0,0) To (1600,4800)
(II) CHROME(0): Using 3600 lines for offscreen memory.
(II) CHROME(0): Using XFree86 Acceleration Architecture (XAA)
(==) CHROME(0): Backing store disabled
(II) CHROME(0): - Backing store set up
(II) CHROME(0): - SW cursor set up
(II) CHROME(0): VIAHWCursorInit
(II) CHROME(0): - Def Color map set up
(II) CHROME(0): VIALoadPalette: numColors: 256
(II) CHROME(0): - Palette loaded
(==) CHROME(0): DPMS enabled
(II) CHROME(0): - DPMS set up
(II) CHROME(0): - Color maps etc. set up
(II) CHROME(0): [drm] Detected AGP vendor 0x1106, device 0x0204
(II) CHROME(0): [drm] Found AGP v3 compatible device. Trying AGP 8X mode.
(II) CHROME(0): [drm] Trying to enable AGP fast writes.
(II) CHROME(0): [drm] drmAgpEnabled succeeded
(II) CHROME(0): [drm] agpAddr = 0xb0000000
(II) CHROME(0): [drm] agpBase = (nil)
(II) CHROME(0): [drm] agpAddr = 0xb0000000
(II) CHROME(0): [drm] agpSize = 0x01e00000
(II) CHROME(0): [drm] agp physical addr = 0x00000000
(II) CHROME(0): [dri] Using AGP.
(II) CHROME(0): [drm] Using 36113888 bytes for DRM memory heap.
(II) CHROME(0): [dri] Frame buffer initialized.
(II) CHROME(0): [DRI] installation complete
(II) CHROME(0): [dri] Kernel data initialized.
(II) CHROME(0): [drm] Initialized AGP ring-buffer, size 0x200000 at AGP offset 0x1e00000.
(II) CHROME(0): direct rendering enabled
(II) CHROME(0): [Xv] Using PCI DMA for Xv image transfer.
(II) CHROME(0): Benchmarking video copy.  Less time is better.
(--) CHROME(0): Timed   libc YUV420 copy... 25459123. Throughput: 37.3 MiB/s.
(--) CHROME(0): Timed kernel YUV420 copy... 15034652. Throughput: 63.1 MiB/s.
(--) CHROME(0): Timed    SSE YUV420 copy... 14982804. Throughput: 63.4 MiB/s.
(--) CHROME(0): Timed    MMX YUV420 copy... 24489888. Throughput: 38.8 MiB/s.
(--) CHROME(0): Timed 3DNow! YUV420 copy... 23052671. Throughput: 41.2 MiB/s.
(--) CHROME(0): Timed   MMX2 YUV420 copy... 14996893. Throughput: 63.3 MiB/s.
(--) CHROME(0): Using SSE YUV42X copy for video.
(II) CHROME(0): [XvMC] Registering chromeXvMC.
(II) CHROME(0): [XvMC] Initialized XvMC extension.
(II) CHROME(0): - Done
(II) CHROME(0): VIASwitchMode
(II) CHROME(0): [drm] Cleaning up DMA ring-buffer.
(II) CHROME(0): VIAWriteMode
(WW) CHROME(0): Unable to determine the refresh rate, using 60.00. Please check your configuration.
(II) CHROME(0): Trying VBE Mode 1024x768 (0xc118) Refresh 60.00:
(II) CHROME(0): ViaVbeSetRefresh
(II) CHROME(0): Active Device: 2
(II) CHROME(0): Refresh Rate Index: 0
(II) CHROME(0): VIAAdjustFrame 0x0
(II) CHROME(0): [drm] Initialized AGP ring-buffer, size 0x200000 at AGP offset 0x1e00000.
(II) CHROME(0): VIALoadPalette: numColors: 256
(II) CHROME(0): VIAAdjustFrame 0x0
(II) CHROME(0): VIAAdjustFrame 1x1
(II) CHROME(0): VIAAdjustFrame 0x0
loic@loic-laptop:~$