U-Boot SPL 2013.04-dirty (Jul 10 2013 - 14:02:53)
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
mmc_send_cmd : timeout: No status update
reading u-boot.img
reading u-boot.img


U-Boot 2013.04-dirty (Jul 10 2013 - 14:02:53)

I2C:   ready
DRAM:  512 MiB
WARNING: Caches not enabled
NAND:  No NAND device found!!!
0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot:  0
gpio: pin 53 (gpio 53) value is 1
mmc_send_cmd : timeout: No status update
Card did not respond to voltage select!
mmc0(part 0) is current device
mmc_send_cmd : timeout: No status update
Card did not respond to voltage select!
No micro SD card found, setting mmcdev to 1
mmc_send_cmd : timeout: No status update
mmc1(part 0) is current device
mmc_send_cmd : timeout: No status update
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 1
reading uEnv.txt
26 bytes read in 3 ms (7.8 KiB/s)
Loaded environment from uEnv.txt
Importing environment from mmc ...
gpio: pin 55 (gpio 55) value is 1
4385024 bytes read in 766 ms (5.5 MiB/s)
gpio: pin 56 (gpio 56) value is 1
24808 bytes read in 52 ms (465.8 KiB/s)
Booting from mmc ...
## Booting kernel from Legacy Image at 80007fc0 ...
   Image Name:   Angstrom/3.8.13/beaglebone
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4384960 Bytes = 4.2 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 80f80000
   Booting using the fdt blob at 0x80f80000
   XIP Kernel Image ... OK
OK
   Using Device Tree in place at 80f80000, end 80f890e7

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[   45.784691] irq 23: nobody cared (try booting with the "irqpoll" option)
[   45.784966] handlers:
[   45.784991] [<c0062129>] irq_default_primary_handler threaded [<c0203dc3>] tps65217_irq
[   45.785028] Disabling IRQ #23
[   45.824143] omap2_mbox_probe: platform not supported
[   45.834747] tps65217-bl tps65217-bl: no platform data provided
[   45.932831] bone-capemgr bone_capemgr.8: slot #0: No cape found
[   45.969936] bone-capemgr bone_capemgr.8: slot #1: No cape found
[   46.007046] bone-capemgr bone_capemgr.8: slot #2: No cape found
[   46.044154] bone-capemgr bone_capemgr.8: slot #3: No cape found
[   46.063936] bone-capemgr bone_capemgr.8: slot #6: BB-BONELT-HDMIN conflict P8.45 (#5:BB-BONELT-HDMI)
[   46.073550] bone-capemgr bone_capemgr.8: slot #6: Failed verification
[   46.094151] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
[   46.101445] bone-capemgr bone_capemgr.8: loader: failed to load slot-6 BB-BONELT-HDMIN:00A0 (prio 2)
[   46.169651] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot 7
[   46.181386] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.7) status -22
[   46.188816] pinctrl-single 44e10800+-----------------------------+21 on device pinctrl-single
[   46.223185] dummy 0-0034: Error -12|                             |
[   46.228975] tda998x 0-0070: Error -|  Cannot open /dev/ttyUSB0!  |
[   46.234621] tda998x 0-0070: Error -|                             |
[   46.292304] tda998x 0-0070: Error -+-----------------------------+
[   46.297896] tda998x 0-0070: Error -121 writing to 0xa
[   46.354784] tda998x 0-0070: Error -121 reading from 0x1
[   46.360355] tda998x 0-0070: Error -121 writing to 0x1
[   46.365746] tda998x 0-0070: Error -121 reading from 0x1
[   46.371316] tda998x 0-0070: Error -121 writing to 0x1
[   46.376785] tda998x 0-0070: Error -121 writing to REG_CURPAGE
[   46.382903] tda998x 0-0070: Error -121 writing to 0x200
[   46.388529] tda998x 0-0070: Error -121 writing to 0x201
[   46.394144] tda998x 0-0070: Error -121 writing to 0x202
[   46.399722] tda998x 0-0070: Error -121 writing to 0x203
[   46.405290] tda998x 0-0070: Error -121 writing to 0x204
[   46.410858] tda998x 0-0070: Error -121 writing to 0x205
[   46.416426] tda998x 0-0070: Error -121 writing to 0x20e
[   46.421992] tda998x 0-0070: Error -121 writing to 0x211
[   46.427563] tda998x 0-0070: Error -121 writing to 0x207
[   46.433132] tda998x 0-0070: Error -121 writing to 0x208
[   46.438697] tda998x 0-0070: Error -121 writing to 0x209
[   46.444293] tda998x 0-0070: Error -121 writing to 0x20a
[   46.449882] tda998x 0-0070: Error -121 writing to 0x206
[   46.455451] tda998x 0-0070: Error -121 writing to REG_CURPAGE
[   46.461562] tda998x 0-0070: Error -121 reading from 0x0
[   46.467148] tda998x 0-0070: Error -121 reading from 0x2
[   46.473031] tilcdc 4830e000.fb: no encoders/connectors found
[   46.478995] tilcdc 4830e000.fb: failed to initialize mode setting
systemd-fsck[85]: Angstrom: clean, 48938/112672 files, 272096/449820 blocks