U-Boot SPL 2017.01-00003-gbd0c067fb2 (Jan 09 2017 - 13:50:24)
Trying to boot from MMC2

U-Boot 2017.01-00003-gbd0c067fb2 (Jan 09 2017 - 13:50:24 -0600), Build: jenkins-github_Bootloader-Builder-499

CPU  : AM335X-GP rev 2.1
I2C:   ready
DRAM:  512 MiB
Reset Source: Global external warm reset has occurred.
Reset Source: Global warm SW reset has occurred.
Reset Source: Power-on reset has occurred.
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
Using default environment

Board: BeagleBone Black
<ethaddr> not set. Validating first E-fuse MAC
BeagleBone: cape eeprom: i2c_probe: 0x54:
BeagleBone: cape eeprom: i2c_probe: 0x55:
BeagleBone: cape eeprom: i2c_probe: 0x56:
BeagleBone: cape eeprom: i2c_probe: 0x57:
Net:   eth0: MII MODE
cpsw
Press SPACE to abort autoboot in 2 seconds
board_name=[A335BNLT] ...
board_rev=[00C0] ...
Card did not respond to voltage select!
Card did not respond to voltage select!
Card did not respond to voltage select!
gpio: pin 56 (gpio 56) value is 0
gpio: pin 55 (gpio 55) value is 0
gpio: pin 54 (gpio 54) value is 0
gpio: pin 53 (gpio 53) value is 1
Card did not respond to voltage select!
Card did not respond to voltage select!
switch to partitions #0, OK
mmc1(part 0) is current device
Scanning mmc 1:1...
gpio: pin 56 (gpio 56) value is 0
gpio: pin 55 (gpio 55) value is 0
gpio: pin 54 (gpio 54) value is 0
gpio: pin 53 (gpio 53) value is 1
switch to partitions #0, OK
mmc1(part 0) is current device
gpio: pin 54 (gpio 54) value is 1
Checking for: /uEnv.txt ...
Checking for: /boot.scr ...
Checking for: /boot/boot.scr ...
Checking for: /boot/uEnv.txt ...
gpio: pin 55 (gpio 55) value is 1
1358 bytes read in 14 ms (94.7 KiB/s)
Loaded environment from /boot/uEnv.txt
debug: [dtb=am335x-boneblack-emmc-overlay.dtb] ...
Using: dtb=am335x-boneblack-emmc-overlay.dtb ...
Checking if uname_r is set in /boot/uEnv.txt...
gpio: pin 56 (gpio 56) value is 1
Running uname_boot ...
loading /boot/vmlinuz-4.4.9-bone-rt-r10 ...
7608888 bytes read in 494 ms (14.7 MiB/s)
loading /boot/dtbs/4.4.9-bone-rt-r10/am335x-boneblack-emmc-overlay.dtb ...
54722 bytes read in 45 ms (1.2 MiB/s)
debug: [uboot_overlay_addr0=/lib/firmware/controller-00A0.dtbo] ...
loading /lib/firmware/controller-00A0.dtbo ...
15778 bytes read in 94 ms (163.1 KiB/s)
debug: [uboot_overlay_addr1=/lib/firmware/BB-ADC-00A0.dtbo] ...
loading /lib/firmware/BB-ADC-00A0.dtbo ...
695 bytes read in 29 ms (22.5 KiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
debug: [dtb_overlay=/lib/firmware/BB-W1-P8.26-00A0.dtbo] ...
loading /lib/firmware/BB-W1-P8.26-00A0.dtbo ...
974 bytes read in 75 ms (11.7 KiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
loading /boot/initrd.img-4.4.9-bone-rt-r10 ...
4765535 bytes read in 318 ms (14.3 MiB/s)
debug: [console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 root=UUID=e5fb43ee-820e-4352-aff6-51510db46f93 ro rootfstype=ext4 rootwait coherent_pool=1M quiet ipv6.disable=1] ...
debug: [bootz 0x82000000 0x88080000:48b75f 88000000] ...
ERROR: Did not find a cmdline Flattened Device Tree
Could not find a valid device tree
debug: [console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 root=/dev/mmcblk1p1 ro rootfstype=ext4 rootwait coherent_pool=1M quiet ipv6.disable=1] ...
debug: [bootz 0x82000000 0x88080000:48b75f 88000000] ...
ERROR: Did not find a cmdline Flattened Device Tree
Could not find a valid device tree
** Invalid partition 2 **
** Invalid partition 3 **
** Invalid partition 4 **
** Invalid partition 5 **
** Invalid partition 6 **
** Invalid partition 7 **
starting USB...
USB0:   Port not available.
link up on port 0, speed 100, full duplex
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10
BOOTP broadcast 11
BOOTP broadcast 12
BOOTP broadcast 13
BOOTP broadcast 14
BOOTP broadcast 15
BOOTP broadcast 16
BOOTP broadcast 17
BOOTP broadcast 18
BOOTP broadcast 19
BOOTP broadcast 20
BOOTP broadcast 21
BOOTP broadcast 22
BOOTP broadcast 23
BOOTP broadcast 24
BOOTP broadcast 25
BOOTP broadcast 26
BOOTP broadcast 27
BOOTP broadcast 28
BOOTP broadcast 29

Retry time exceeded; starting again
missing environment variable: pxeuuid
Retrieving file: pxelinux.cfg/01-78-a5-04-ca-fb-dc
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/00000000
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/0000000
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/000000
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/00000
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/0000
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/000
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/00
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/0
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/default-arm-am33xx
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/default-arm
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/default
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Config file not found
starting USB...
USB0:   Port not available.
link up on port 0, speed 100, full duplex
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10
BOOTP broadcast 11
BOOTP broadcast 12
BOOTP broadcast 13
BOOTP broadcast 14
BOOTP broadcast 15
BOOTP broadcast 16
BOOTP broadcast 17
BOOTP broadcast 18
BOOTP broadcast 19
BOOTP broadcast 20
BOOTP broadcast 21
BOOTP broadcast 22