JLinkGDBServerCL

SEGGER J-Link GDB Server V5.10n Command Line Version

JLinkARM.dll V5.10n (DLL compiled Feb 19 2016 18:45:10)

-----GDB Server start settings-----
GDBInit file:                  none
GDB Server Listening port:     2331
SWO raw output listening port: 2332
Terminal I/O port:             2332
Accept remote connection:      localhost only
Generate logfile:              off
Verify download:               on
Init regs on start:            on
Silent mode:                   off
Single run mode:               on
Target connection timeout:     0 ms
------J-Link related settings------
J-Link Host interface:         USB
J-Link script:                 none
J-Link settings file:          none
------Target related settings------
Target device:                 MK82FN256xxx15
Target interface:              SWD
Target interface speed:        1000kHz
Target endian:                 little

Connecting to J-Link...
J-Link is connected.
Firmware: J-Link OpenSDA 2 compiled May  6 2016 11:04:17
Hardware: V1.00
S/N: 621000000
Checking target voltage...
Target voltage: 3.30 V
Listening on TCP/IP port 2331
Connecting to target...Connected to target
Waiting for GDB connection...Connected to 127.0.0.1
Reading all registers
Read 4 bytes @ address 0x00000000 (Data = 0x20030000)
Target interface speed set to 30 kHz
Resetting target
Halting target CPU...
...Target halted (PC = 0x000004D8)
R0 = 00000000, R1 = 00000000, R2 = 00000000, R3 = 00000000
R4 = 00000000, R5 = 00000000, R6 = 00000000, R7 = 00000000
R8 = 00000000, R9 = 00000000, R10= 00000000, R11= 00000000
R12= 00000000, R13= 20030000, MSP= 20030000, PSP= 00000000
R14(LR) = FFFFFFFF, R15(PC) = 000004D8
XPSR 01000000, APSR 00000000, EPSR 01000000, IPSR 00000000
CFBP 00000000, CONTROL 00, FAULTMASK 00, BASEPRI 00, PRIMASK 00
Reading all registers
Select auto target interface speed (1429 kHz)
Flash breakpoints enabled
Semi-hosting enabled (Handle on BKPT)
Wrong client mask. Semihosting I/O not changed.


*** J-Link V5.10n Warning ***
The connected emulator does not support serial wire output (SWO).

*** J-Link V5.10n Warning ***

Failed to disable SWO.
Failed to enable SWO. Could not determine a suitable SWO speed!
Downloading 16 bytes @ address 0x00000400 - Verified OK
Downloading 960 bytes @ address 0x1FFF0000 - Verified OK
Downloading 16176 bytes @ address 0x20000000 - Verified OK
Downloading 6704 bytes @ address 0x20003F30 - Verified OK
Downloading 48 bytes @ address 0x20005960 - Verified OK
Downloading 216 bytes @ address 0x20005990 - Verified OK
Downloading 4 bytes @ address 0x20005A68 - Verified OK
Downloading 4 bytes @ address 0x20005A6C - Verified OK
Downloading 112 bytes @ address 0x20005A70 - Verified OK
Writing register (PC = 0x200000c8)
Read 4 bytes @ address 0x200000C8 (Data = 0x4809B672)
Resetting target
Halting target CPU...
...Target halted (PC = 0x000004D8)
Read 2 bytes @ address 0x200029EE (Data = 0xF001)
Read 2 bytes @ address 0x200029EE (Data = 0xF001)
Read 2 bytes @ address 0x200029EE (Data = 0xF001)
R0 = 00000000, R1 = 00000000, R2 = 00000000, R3 = 00000000
R4 = 00000000, R5 = 00000000, R6 = 00000000, R7 = 00000000
R8 = 00000000, R9 = 00000000, R10= 00000000, R11= 00000000
R12= 00000000, R13= 20030000, MSP= 20030000, PSP= 00000000
R14(LR) = FFFFFFFF, R15(PC) = 000004D8
XPSR 01000000, APSR 00000000, EPSR 01000000, IPSR 00000000
CFBP 00000000, CONTROL 00, FAULTMASK 00, BASEPRI 00, PRIMASK 00
Reading all registers
Read 4 bytes @ address 0x000004D8 (Data = 0x480DB672)
Setting breakpoint @ address 0x200029EE, Size = 2, BPHandle = 0x0001
Starting target CPU...