<6>[    4.580000] ===========================ft5x_ts_init=====================
<6>[    4.580000] ctp_fetch_sysconfig_para.
<6>[    4.590000] ctp_fetch_sysconfig_para: after: ctp_twi_addr is 0x38, dirty_addr_buf: 0x38. dirty_addr_buf[1]: 0xfffe
<6>[    4.600000] ctp_fetch_sysconfig_para: ctp_twi_id is 2.
<6>[    4.600000] ctp_fetch_sysconfig_para: screen_max_x = 800.
<6>[    4.610000] ctp_fetch_sysconfig_para: screen_max_y = 480.
<6>[    4.610000] ctp_fetch_sysconfig_para: revert_x_flag = 1.
<6>[    4.620000] ctp_fetch_sysconfig_para: revert_y_flag = 0.
<6>[    4.620000] ctp_fetch_sysconfig_para: exchange_x_y_flag = 0.
<6>[    4.630000] ft5x_ts_init: after fetch_sysconfig_para:  normal_i2c: 0x38. normal_i2c[1]: 0xfffe
<7>[    4.640000] script parser fetch err.
<4>[    4.640000] ctp_init_platform_resource: tp_reset request gpio fail!
<6>[    4.650000] ctp_wakeup.
<6>[    4.690000] ctp_detect: Detected chip ft5x_ts at adapter 2, address 0x38
<6>[    4.700000] ====ft5x_ts_probe begin=====.
<6>[    4.700000] fts_ctpm_fw_upgrade_with_i_file.
<6>[    4.820000] =========buf[0] = 0xa6
<6>[    4.820000] =========buf[1] = 0xa6
<6>[    4.820000] a == 166,  b== 34
<6>[    5.000000] Step 1: Reset CTPM test
<6>[    5.040000] Step 2: Enter update mode.
<6>[    5.060000] ====Step 3:check READ-ID====
<6>[    5.080000] Step 3: CTPM ID,ID1 = 0x79,ID2 = 0x3
<6>[    6.590000] Step 4: erase.
<6>[    6.590000] Step 5: start upgrade.
<6>[    6.640000] upgrade the 0x0 th byte.
<6>[    6.970000] upgrade the 0x400 th byte.
<6>[    7.300000] upgrade the 0x800 th byte.
<6>[    7.630000] upgrade the 0xc00 th byte.
<6>[    7.960000] upgrade the 0x1000 th byte.
<6>[    8.290000] upgrade the 0x1400 th byte.
<6>[    8.620000] upgrade the 0x1800 th byte.
<6>[    8.950000] upgrade the 0x1c00 th byte.
<6>[    9.280000] upgrade the 0x2000 th byte.
<6>[    9.610000] upgrade the 0x2400 th byte.
<6>[    9.940000] upgrade the 0x2800 th byte.
<6>[   10.270000] upgrade the 0x2c00 th byte.
<6>[   10.600000] upgrade the 0x3000 th byte.
<6>[   10.930000] upgrade the 0x3400 th byte.
<6>[   11.260000] upgrade the 0x3800 th byte.
<6>[   11.590000] upgrade the 0x3c00 th byte.
<6>[   11.920000] upgrade the 0x4000 th byte.
<6>[   12.250000] upgrade the 0x4400 th byte.
<6>[   12.580000] upgrade the 0x4800 th byte.
<6>[   12.910000] upgrade the 0x4c00 th byte.
<6>[   13.240000] upgrade the 0x5000 th byte.
<6>[   13.570000] upgrade the 0x5400 th byte.
<6>[   13.900000] upgrade the 0x5800 th byte.
<6>[   14.230000] upgrade the 0x5c00 th byte.
<6>[   14.560000] upgrade the 0x6000 th byte.
<6>[   14.890000] upgrade the 0x6400 th byte.
<6>[   15.270000] Step 6:  ecc read 0x90, new firmware 0xcb.
<6>[   15.270000] [FTS] upgrade failed i_ret = 5.
<6>[   15.280000] input: ft5x_ts as /devices/virtual/input/input2
<6>[   15.280000] ==register_early_suspend =
<6>[   15.290000] CONFIG_FT5X0X_MULTITOUCH is defined.
<6>[   15.290000] ctp_set_irq_mode: config gpio to int mode.
<6>[   15.300000]  INTERRUPT CONFIG
<6>[   15.300000] ==CTP_IRQ_NO=
<6>[   15.300000] ==ft5x_ts_probe over =