Linux version 2.6.27.8 (root@darkstar) (gcc version 4.2.4) #1 SMP Sun Dec 7 08:30:31 Local time zone must be set--see zic m
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000002e60c000 (usable)
 BIOS-e820: 000000002e60c000 - 000000002e80c000 (ACPI NVS)
 BIOS-e820: 000000002e80c000 - 000000002fd70000 (usable)
 BIOS-e820: 000000002fd70000 - 000000002fdbf000 (reserved)
 BIOS-e820: 000000002fdbf000 - 000000002fe92000 (usable)
 BIOS-e820: 000000002fe92000 - 000000002febf000 (ACPI NVS)
 BIOS-e820: 000000002febf000 - 000000002fee2000 (usable)
 BIOS-e820: 000000002fee2000 - 000000002fef7000 (ACPI data)
 BIOS-e820: 000000002fef7000 - 000000002ff00000 (usable)
 BIOS-e820: 00000000f7000000 - 00000000f8000000 (reserved)
 BIOS-e820: 00000000feb00000 - 00000000feb01000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
DMI 2.6 present.
last_pfn = 0x2ff00 max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
kernel direct mapping tables up to 2ff00000 @ 7000-d000
RAMDISK: 2e392000 - 2e5eaf44
ACPI: RSDP 000FE020, 0024 (r2 ACRSYS)
ACPI: XSDT 2FEF6120, 005C (r1 ACRSYS ACRPRDCT        3       1000013)
ACPI: FACP 2FEF5000, 00F4 (r4 ACRSYS ACRPRDCT        3 1025  1000013)
ACPI: DSDT 2FEE9000, 8E28 (r1 ACRSYS ACRPRDCT     1000 1025  1000013)
ACPI: FACS 2FE9C000, 0040
ACPI: HPET 2FEF4000, 0038 (r1 ACRSYS ACRPRDCT        1 1025  1000013)
ACPI: APIC 2FEF3000, 0068 (r2 ACRSYS ACRPRDCT        1 1025  1000013)
ACPI: MCFG 2FEF2000, 003C (r1 ACRSYS ACRPRDCT        1 1025  1000013)
ACPI: BOOT 2FEE8000, 0028 (r1 ACRSYS ACRPRDCT        1 1025  1000013)
ACPI: SLIC 2FEE7000, 0176 (r1 ACRSYS ACRPRDCT        1 1025  1000013)
ACPI: SSDT 2FEE6000, 0140 (r1 AMD    PowerNow        1 AMD         1)
ACPI: DMI detected: Acer
0MB HIGHMEM available.
767MB LOWMEM available.
  mapped low ram: 0 - 2ff00000
  low ram: 00000000 - 2ff00000
  bootmap 00009000 - 0000efe0
(9 early reservations) ==> bootmem [0000000000 - 002ff00000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
  #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
  #3 [0000100000 - 00009f2210]    TEXT DATA BSS ==> [0000100000 - 00009f2210]
  #4 [002e392000 - 002e5eaf44]          RAMDISK ==> [002e392000 - 002e5eaf44]
  #5 [00009f3000 - 00009f7000]    INIT_PG_TABLE ==> [00009f3000 - 00009f7000]
  #6 [000009fc00 - 0000100000]    BIOS reserved ==> [000009fc00 - 0000100000]
  #7 [0000007000 - 0000009000]          PGTABLE ==> [0000007000 - 0000009000]
  #8 [0000009000 - 000000f000]          BOOTMAP ==> [0000009000 - 000000f000]
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x0002ff00
  HighMem  0x0002ff00 -> 0x0002ff00
Movable zone start PFN for each node
early_node_map[6] active PFN ranges
    0: 0x00000000 -> 0x0000009f
    0: 0x00000100 -> 0x0002e60c
    0: 0x0002e80c -> 0x0002fd70
    0: 0x0002fdbf -> 0x0002fe92
    0: 0x0002febf -> 0x0002fee2
    0: 0x0002fef7 -> 0x0002ff00
On node 0 totalpages: 195598
free_area_init_node: node 0, pgdat c08ef680, node_mem_map c1000000
  DMA zone: 3967 pages, LIFO batch:0
  Normal zone: 190097 pages, LIFO batch:31
Detected use of extended apic ids on hypertransport bus
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
ACPI: HPET id: 0x1002a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
PM: Registered nosave memory: 000000002e60c000 - 000000002e80c000
PM: Registered nosave memory: 000000002fd70000 - 000000002fdbf000
PM: Registered nosave memory: 000000002fe92000 - 000000002febf000
PM: Registered nosave memory: 000000002fee2000 - 000000002fef7000
Allocating PCI resources starting at 30000000 (gap: 2ff00000:c7100000)
PERCPU: Allocating 39324 bytes of per cpu data
NR_CPUS: 32, nr_cpu_ids: 2, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 194064
Kernel command line: initrd=/boot/initrd.gz ramdisk_size=6666 root=/dev/ram0 rw copy2ram autoexec=xconf;telinit~4 BOOT_IMAGE=/boot/vmlinuz
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
TSC: PIT calibration confirmed by PMTIMER.
TSC: using PIT calibration value
Detected 1196.987 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 763128k/785408k available (6197k kernel code, 18716k reserved, 2023k data, 392k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xffe18000 - 0xfffff000   (1948 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf0800000 - 0xff7fe000   ( 239 MB)
    lowmem  : 0xc0000000 - 0xeff00000   ( 767 MB)
      .init : 0xc0913000 - 0xc0975000   ( 392 kB)
      .data : 0xc070d417 - 0xc09070f8   (2023 kB)
      .text : 0xc0100000 - 0xc070d417   (6197 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
hpet clockevent registered
Calibrating delay loop (skipped), value calculated using timer frequency.. 2393.97 BogoMIPS (lpj=4787948)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0(2) -> Core 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using C1E aware idle routine
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080609
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: AMD Athlon(tm) X2 Dual Core Processor L310 stepping 02
Booting processor 1/1 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 2394.03 BogoMIPS (lpj=4788069)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1(2) -> Core 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: AMD Athlon(tm) X2 Dual Core Processor L310 stepping 02
Brought up 2 CPUs
System has AMD C1E enabled
Switch to broadcast mode on CPU1
Total of 2 processors activated (4788.00 BogoMIPS).
Switch to broadcast mode on CPU0
net_namespace: 768 bytes
xor: automatically using best checksumming function: pIII_sse
   pIII_sse  :  3695.000 MB/sec
xor: using function: pIII_sse (3695.000 MB/sec)
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: MCFG configuration 0: base f7000000 segment 0 buses 0 - 15
PCI: MCFG area at f7000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: missing confirmations, switch off interrupt mode.
ACPI: EC: GPE = 0x3, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
pci 0000:00:05.0: PME# disabled
PCI: 0000:00:11.0 reg 10 io port: [8038, 803f]
PCI: 0000:00:11.0 reg 14 io port: [804c, 804f]
PCI: 0000:00:11.0 reg 18 io port: [8030, 8037]
PCI: 0000:00:11.0 reg 1c io port: [8048, 804b]
PCI: 0000:00:11.0 reg 20 io port: [8010, 801f]
PCI: 0000:00:11.0 reg 24 32bit mmio: [52306000, 523063ff]
pci 0000:00:11.0: set SATA to AHCI mode
PCI: 0000:00:12.0 reg 10 32bit mmio: [52305000, 52305fff]
PCI: 0000:00:12.1 reg 10 32bit mmio: [52304000, 52304fff]
PCI: 0000:00:12.2 reg 10 32bit mmio: [52306400, 523064ff]
pci 0000:00:12.2: supports D1
pci 0000:00:12.2: supports D2
pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:12.2: PME# disabled
PCI: 0000:00:14.1 reg 10 io port: [0, 7]
PCI: 0000:00:14.1 reg 14 io port: [0, 3]
PCI: 0000:00:14.1 reg 18 io port: [0, 7]
PCI: 0000:00:14.1 reg 1c io port: [0, 3]
PCI: 0000:00:14.1 reg 20 io port: [8000, 800f]
PCI: 0000:00:14.2 reg 10 64bit mmio: [52300000, 52303fff]
pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
pci 0000:00:14.2: PME# disabled
PCI: 0000:01:05.0 reg 10 32bit mmio: [40000000, 4fffffff]
PCI: 0000:01:05.0 reg 14 io port: [7000, 70ff]
PCI: 0000:01:05.0 reg 18 32bit mmio: [52200000, 5220ffff]
PCI: 0000:01:05.0 reg 24 32bit mmio: [52100000, 521fffff]
pci 0000:01:05.0: supports D1
pci 0000:01:05.0: supports D2
PCI: bridge 0000:00:01.0 io port: [7000, 7fff]
PCI: bridge 0000:00:01.0 32bit mmio: [52100000, 522fffff]
PCI: bridge 0000:00:01.0 64bit mmio pref: [40000000, 4fffffff]
PCI: 0000:02:00.0 reg 10 64bit mmio: [51100000, 51103fff]
pci 0000:02:00.0: supports D1
pci 0000:02:00.0: supports D2
PCI: bridge 0000:00:04.0 io port: [3000, 6fff]
PCI: bridge 0000:00:04.0 32bit mmio: [51100000, 520fffff]
PCI: bridge 0000:00:04.0 64bit mmio pref: [50000000, 50ffffff]
PCI: 0000:08:00.0 reg 10 64bit mmio: [51000000, 5103ffff]
PCI: 0000:08:00.0 reg 18 io port: [2000, 207f]
pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:08:00.0: PME# disabled
PCI: bridge 0000:00:05.0 io port: [2000, 2fff]
PCI: bridge 0000:00:05.0 32bit mmio: [51000000, 510fffff]
pci 0000:00:14.4: transparent bridge
PCI: bridge 0000:00:14.4 io port: [1000, 1fff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
system 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:01: iomem range 0xf7000000-0xf7ffffff could not be reserved
system 00:08: ioport range 0x400-0x4cf has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x4d6-0x4d6 has been reserved
system 00:08: ioport range 0x680-0x6ff has been reserved
system 00:08: ioport range 0x77a-0x77a has been reserved
system 00:08: ioport range 0xc00-0xc01 has been reserved
system 00:08: ioport range 0xc14-0xc14 has been reserved
system 00:08: ioport range 0xc50-0xc52 has been reserved
system 00:08: ioport range 0xc6c-0xc6c has been reserved
system 00:08: ioport range 0xc6f-0xc6f has been reserved
system 00:08: ioport range 0xcd0-0xcdb has been reserved
system 00:08: ioport range 0xfd60-0xfd63 has been reserved
system 00:09: iomem range 0xe0000-0xfffff could not be reserved
system 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0:   IO window: 0x7000-0x7fff
pci 0000:00:01.0:   MEM window: 0x52100000-0x522fffff
pci 0000:00:01.0:   PREFETCH window: 0x00000040000000-0x0000004fffffff
pci 0000:00:04.0: PCI bridge, secondary bus 0000:02
pci 0000:00:04.0:   IO window: 0x3000-0x6fff
pci 0000:00:04.0:   MEM window: 0x51100000-0x520fffff
pci 0000:00:04.0:   PREFETCH window: 0x00000050000000-0x00000050ffffff
pci 0000:00:05.0: PCI bridge, secondary bus 0000:08
pci 0000:00:05.0:   IO window: 0x2000-0x2fff
pci 0000:00:05.0:   MEM window: 0x51000000-0x510fffff
pci 0000:00:05.0:   PREFETCH window: disabled
pci 0000:00:14.4: PCI bridge, secondary bus 0000:09
pci 0000:00:14.4:   IO window: 0x1000-0x1fff
pci 0000:00:14.4:   MEM window: disabled
pci 0000:00:14.4:   PREFETCH window: disabled
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:04.0: setting latency timer to 64
pci 0000:00:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:05.0: setting latency timer to 64
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffff]
bus: 01 index 0 io port: [7000, 7fff]
bus: 01 index 1 mmio: [52100000, 522fffff]
bus: 01 index 2 mmio: [40000000, 4fffffff]
bus: 01 index 3 mmio: [0, 0]
bus: 02 index 0 io port: [3000, 6fff]
bus: 02 index 1 mmio: [51100000, 520fffff]
bus: 02 index 2 mmio: [50000000, 50ffffff]
bus: 02 index 3 mmio: [0, 0]
bus: 08 index 0 io port: [2000, 2fff]
bus: 08 index 1 mmio: [51000000, 510fffff]
bus: 08 index 2 mmio: [0, 0]
bus: 08 index 3 mmio: [0, 0]
bus: 09 index 0 io port: [1000, 1fff]
bus: 09 index 1 mmio: [0, 0]
bus: 09 index 2 mmio: [0, 0]
bus: 09 index 3 io port: [0, ffff]
bus: 09 index 4 mmio: [0, ffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 2403k freed
Simple Boot Flag at 0x44 set to 0x1
apm: BIOS not found.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.29 [Flags: R/O].
JFS: nTxBlock = 5984, nTxLock = 47879
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
OCFS2 1.5.0
OCFS2 Node Manager 1.5.0
GFS2 (built Dec  7 2008 08:26:41) installed
msgmni has been set to 1496
async_tx: api initialized (sync-only)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:05.0: Boot video device
pcieport-driver 0000:00:04.0: setting latency timer to 64
pcieport-driver 0000:00:04.0: found MSI capability
pci_express 0000:00:04.0:pcie00: allocate port service
pci_express 0000:00:04.0:pcie02: allocate port service
pcieport-driver 0000:00:05.0: setting latency timer to 64
pcieport-driver 0000:00:05.0: found MSI capability
pci_express 0000:00:05.0:pcie00: allocate port service
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input2
ACPI: Sleep Button (CM) [SLPB]
input: Lid Switch as /class/input/input3
ACPI: Lid Switch [LID]
ACPI: processor limited to max C-state 1
processor ACPI0007:00: registered as cooling_device0
ACPI: Processor [C000] (supports 8 throttling states)
processor ACPI0007:01: registered as cooling_device1
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (58 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
floppy0: no floppy controllers found
brd: module loaded
loop: module loaded
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.20)
Uniform Multi-Platform E-IDE driver
atiixp 0000:00:14.1: IDE controller (0x1002:0x439c rev 0x00)
pci 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
atiixp 0000:00:14.1: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x8000-0x8007
    ide1: BM-DMA at 0x8008-0x800f
Probing IDE interface ide0...
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
ide_generic: I/O resource 0x1F0-0x1F7 not free.
ide_generic: I/O resource 0x170-0x177 not free.
ide-floppy driver 1.00
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
Adaptec aacraid driver 1.1-5[2456]-ms
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
scsi: <fdomain> Detection failed (no card)
sym53c416.c: Version 1.0.0-ac
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver: 8.02.01-k7
iscsi: registered transport (qla4xxx)
QLogic iSCSI HBA Driver
Emulex LightPulse Fibre Channel SCSI driver 8.2.7
Copyright(c) 2004-2008 Emulex.  All rights reserved.
Failed initialization of WD-7000 SCSI card!
DC390: clustering now enabled by default. If you get problems load
	with "disable_clustering=1" and report to maintainers
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.04.01 Thu July 24 11:41:51 PST 2008
GDT-HA: Storage RAID Controller Driver. Version: 3.05
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.011.
nsp32: loading...
ipr: IBM Power RAID SCSI Device Driver version: 2.4.1 (April 24, 2007)
RocketRAID 3xxx/4xxx Controller driver v1.3 (071203)
st: Version 20080504, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ahci 0000:00:11.0: version 3.0
ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
ahci 0000:00:11.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m1024@0x52306000 port 0x52306100 irq 22
ata2: SATA max UDMA/133 abar m1024@0x52306000 port 0x52306180 irq 22
ata3: SATA max UDMA/133 abar m1024@0x52306000 port 0x52306200 irq 22
ata4: SATA max UDMA/133 abar m1024@0x52306000 port 0x52306280 irq 22
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: Hitachi HTS545025B9A300, PB2OC60F, max UDMA/133
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: HL-DT-STDVDRAM GT30N, 1.01, max UDMA/100, ATAPI AN
ata3.00: configured for UDMA/100
ata4: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access     ATA      Hitachi HTS54502 PB2O PQ: 0 ANSI: 5
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2
sd 2:0:0:0: [sda] Attached SCSI disk
scsi 4:0:0:0: CD-ROM            HL-DT-ST DVDRAM GT30N     1.01 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 4:0:0:0: Attached scsi CD-ROM sr0
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Bus Adapter OSM v1.317
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
Fusion MPT FC Host driver 3.04.07
Fusion MPT SAS Host driver 3.04.07
usbmon: debugfs is not available
ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:12.2: setting latency timer to 64
ehci_hcd 0000:00:12.2: EHCI Host Controller
ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:12.2: debug port 1
ehci_hcd 0000:00:12.2: irq 17, io mem 0x52306400
ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:12.0: setting latency timer to 64
ohci_hcd 0000:00:12.0: OHCI Host Controller
ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:12.0: irq 16, io mem 0x52305000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
usb 1-4: new high speed USB device using ehci_hcd and address 2
ohci_hcd 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:12.1: setting latency timer to 64
ohci_hcd 0000:00:12.1: OHCI Host Controller
ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:12.1: irq 16, io mem 0x52304000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
usb 1-4: configuration #1 chosen from 1 choice
USB Universal Host Controller Interface driver v3.0
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
usb 1-5: new high speed USB device using ehci_hcd and address 3
usb 1-5: configuration #1 chosen from 1 choice
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:MSS0] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
input: AT Translated Set 2 keyboard as /class/input/input4
raid6: int32x1    447 MB/s
raid6: int32x2    471 MB/s
raid6: int32x4    457 MB/s
raid6: int32x8    328 MB/s
raid6: mmxx1      967 MB/s
raid6: mmxx2     1747 MB/s
raid6: sse1x1     977 MB/s
raid6: sse1x2    1650 MB/s
raid6: sse2x1    1615 MB/s
raid6: sse2x2    2235 MB/s
raid6: using algorithm sse2x2 (2235 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: multipath personality registered for level -4
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Starting balanced_irq
Using IPI No-Shortcut mode
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
EXT4-fs warning (device ram0): ext4_fill_super: extents feature not enabled on this filesystem, use tune2fs.

EXT4-fs: ram0: not marked OK to use with test code.
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 392k freed
squashfs: version 3.4 (2008/08/26) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
aufs 20081201
fuse init (API version 7.9)
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
scsi 6:0:0:0: Direct-Access     Generic- Multi-Card       1.00 PQ: 0 ANSI: 0 CCS
sd 6:0:0:0: [sdb] 7823360 512-byte hardware sectors (4006 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sd 6:0:0:0: [sdb] 7823360 512-byte hardware sectors (4006 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 6:0:0:0: [sdb] Attached SCSI removable disk
usb-storage: device scan complete
GFS2: path_lookup on memory/boot returned error
GFS2: gfs2 mount does not exist
shpchp: HPC vendor_id 1022 device_id 9602 ss_vid 0 ss_did 0
shpchp: shpc_init: cannot reserve MMIO region
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
HDA Intel 0000:00:14.2: setting latency timer to 64
sd 2:0:0:0: Attached scsi generic sg0 type 0
sr 4:0:0:0: Attached scsi generic sg1 type 5
sd 6:0:0:0: Attached scsi generic sg2 type 0
acpi device:04: registered as cooling_device2
input: Video Bus as /class/input/input5
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device CNF7017 (04f2:b044)
input: CNF7017 as /class/input/input6
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
input: PS/2 Synaptics TouchPad as /class/input/input7
input: PC Speaker as /class/input/input8
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
Linux agpgart interface v0.103
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
hda-intel: Invalid position buffer, using LPIB read method instead.