Syslog (libbladerf: BLADERF_LOG_LEVEL="verbose")
================================================
Feb 11 18:29:55 XXXXXXX mtp-probe: bus: 10, device: 13 was not an MTP device
Feb 11 18:30:01 XXXXXXX root: antivirus: No argument passed, going through normal checks
Feb 11 18:30:02 XXXXXXX NetworkManager[1523]:    keyfile: updating /etc/NetworkManager/system-connections/SEMCGWLI1
Feb 11 18:32:42 XXXXXXX bladeRF[20007]: [DEBUG @ bladerf.c:1123] Log verbosity has been set to: 0
Feb 11 18:32:42 XXXXXXX bladeRF[20007]: [DEBUG @ init_fini.c:90] libbladeRF 1.2.0-git-4e78b05: initializing
Feb 11 18:32:42 XXXXXXX bladeRF[20007]: [DEBUG @ bladerf.c:1123] Log verbosity has been set to: 0
Feb 11 18:32:42 XXXXXXX bladeRF[20007]: [DEBUG @ init_fini.c:98] libbladeRF 1.2.0-git-4e78b05: deinitializing
Feb 11 18:32:53 XXXXXXX kernel: [1222536.275655] usb 10-2: USB disconnect, device number 13
Feb 11 18:32:56 XXXXXXX kernel: [1222539.831746] usb 10-2: new SuperSpeed USB device number 14 using xhci_hcd
Feb 11 18:32:56 XXXXXXX kernel: [1222539.852590] usb 10-2: New USB device found, idVendor=1d50, idProduct=6066
Feb 11 18:32:56 XXXXXXX kernel: [1222539.852596] usb 10-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Feb 11 18:32:56 XXXXXXX kernel: [1222539.852599] usb 10-2: Product: bladeRF
Feb 11 18:32:56 XXXXXXX kernel: [1222539.852602] usb 10-2: Manufacturer: Nuand
Feb 11 18:32:56 XXXXXXX kernel: [1222539.852605] usb 10-2: SerialNumber: 9d39ad51b7873293c26c7883b487d5b1
Feb 11 18:32:56 XXXXXXX mtp-probe: checking bus 10, device 14: "/sys/devices/pci0000:00/0000:00:01.0/0000:03:00.0/usb10/10-2"
Feb 11 18:32:56 XXXXXXX mtp-probe: bus: 10, device: 14 was not an MTP device
Feb 11 18:33:09 XXXXXXX bladeRF[20107]: [DEBUG @ bladerf.c:1123] Log verbosity has been set to: 0
Feb 11 18:33:09 XXXXXXX bladeRF[20107]: [DEBUG @ init_fini.c:90] libbladeRF 1.2.0-git-4e78b05: initializing
Feb 11 18:33:09 XXXXXXX kernel: [1222553.164078] usb 10-2: reset SuperSpeed USB device number 14 using xhci_hcd
Feb 11 18:33:09 XXXXXXX bladeRF[20107]: [INFO @ usb.c:480] FX3 FW v1.7.1 does not support the "device ready" query.#012#011Ensure flash-autoloading completes before opening a device.#012#011Upgrade the FX3 firmware to avoid this message in the future.#012
Feb 11 18:38:50 XXXXXXX dhclient: DHCPREQUEST of 10.129.42.172 on eth0 to 10.129.0.196 port 67
Feb 11 18:38:50 XXXXXXX dhclient: DHCPACK of 10.129.42.172 from 10.129.0.196
Feb 11 18:38:50 XXXXXXX dhclient: bound to 10.129.42.172 -- renewal in 26861 seconds.
Feb 11 18:38:51 XXXXXXX dhclient: Forward map from seldlx11530.corpusers.net. to 10.129.42.172 FAILED: Has an address record but no DHCID, not mine.
Feb 11 18:39:52 XXXXXXX kernel: [1222956.174308] traps: bladeRF-cli[20107] trap divide error ip:7f0e29457177 sp:7fff3499fcf0 error:0 in libbladeRF.so.1[7f0e2944b000+2c000]
Feb 11 18:42:26 XXXXXXX bladeRF[21969]: [DEBUG @ bladerf.c:1123] Log verbosity has been set to: 0
Feb 11 18:42:26 XXXXXXX bladeRF[21969]: [DEBUG @ init_fini.c:90] libbladeRF 1.2.0-git-4e78b05: initializing
Feb 11 18:42:38 XXXXXXX bladeRF[21969]: [DEBUG @ bladerf.c:1123] Log verbosity has been set to: 0
Feb 11 18:42:38 XXXXXXX bladeRF[21969]: [DEBUG @ init_fini.c:98] libbladeRF 1.2.0-git-4e78b05: deinitializing


CLI session
============
bladeRF :) ]$ bladeRF-cli -i
bladeRF[20107]: [DEBUG @ bladerf.c:1123] Log verbosity has been set to: 0
bladeRF[20107]: [DEBUG @ init_fini.c:90] libbladeRF 1.2.0-git-4e78b05: initializing
bladeRF[20107]: [INFO @ usb.c:480] FX3 FW v1.7.1 does not support the "device ready" query.
        Ensure flash-autoloading completes before opening a device.
        Upgrade the FX3 firmware to avoid this message in the future.

bladeRF> set tx freq 945.401MHz

  set: Invalid parameter (tx)

bladeRF> set freq tx 945.401MHz

  set: Invalid parameter (freq)

bladeRF> set tx frequency 945.401MHz

  set: Invalid parameter (tx)

bladeRF> set frequency 945.401MHz

  Set RX frequency:  945401000Hz
  Set TX frequency:  945401000Hz

bladeRF> set TX frequency 945.401MHz

  set: Invalid parameter (TX)

bladeRF> set frequency tx 945.401MHz

  Set TX frequency:  945401000Hz

bladeRF> set frequency rx 900.401MHz

  Set RX frequency:  900401000Hz

bladeRF> set frequency tx 900.401MHz

  Set TX frequency:  900401000Hz

bladeRF> set frequency rx 945.401MHz

  Set RX frequency:  945401000Hz

bladeRF> print rxvga2

  RXVGA2 Gain:   3dB

bladeRF> set rxvga2 8
bladeRF> cal lms

  Calibrating LMS LPF tuning module...
    LPF tuning module: 25

  Calibrating LMS TX LPF modules...
    TX LPF I filter: 37
    TX LPF Q filter: 33

  Calibrating LMS RX LPF modules...
    RX LPF I filter: 23
    RX LPF Q filter: 29

  Calibrating LMS RXVGA2 modules...
    RX VGA2 DC reference module: 25
    RX VGA2 stage 1, I channel: 33
    RX VGA2 stage 1, Q channel: 33
    RX VGA2 stage 2, I channel: 29
    RX VGA2 stage 2, Q channel: 30

bladeRF> cal dc rx

  RX DC I Setting = 66, error ~= 1
  RX DC Q Setting = 154, error ~= 0

bladeRF> cal table dc rx

Floating point exception0 Hz...    I=99   (avg: 2   ), Q=89   (avg: 0   )
[23059623@seldlx11530 bladeRF :( ]$ bladeRF-cli -i
bladeRF[21969]: [DEBUG @ bladerf.c:1123] Log verbosity has been set to: 0
bladeRF[21969]: [DEBUG @ init_fini.c:90] libbladeRF 1.2.0-git-4e78b05: initializing
No device(s) attached.
bladeRF>