(Filename: 16437-43 COFFEE SNACK CADDY BODY TEST.tap)
  (Post processor: CandCNCPlasmaLLCNC-rev17B.scpost)
  (Date: 15/08/2016)
  G20 (Units: Inches)
  F10.0
  G90 G40
  G64 P0.010 Q0.001 (tracking tolerances set to 0.01)
  M68 E0 Q10
  (Part: 16437-43 COFFEE SNACK CADDY BODY)
 (Preset Volts: 78)  (Preset AMPS: 45)
  ( Air Pressure Preset: 75)
  ( Soft pierce is off )
 ( Suggested Tip Size: 45 )
  ( DTHC Delay: 1 sec )
  ( Min Cut Length for DTHC ON : 20 units )
  M68 E0 Q900  (Global DTHC ON/OFF is ON )
  G4 P.1
  M68 E0 Q378 (Preset Volts set to 78 Volts)
  G4 P.1
  M68 E0 Q445  ( Preset Amps set to 45 Amps)
  G4 P.1
  M68 E0 Q875  ( Air pressure set to 75 PSI)
  G4 P.1
  M68 E0 Q510 (DTHC Delay set to 1 Seconds)
  G4 P.1
   M68 E0 Q711  (DTHCIV tuning set to level 1)
  G4 P.1
  M0 (Settings Check)
 ( ###########################)
  (Paused:  Check the DTHC Settings )
  ( Hit RUN to continue)
 ( ###########################)
  G0  Z2.000
  X-0.223 Y2.355
  G0 Z0.50
  o<touchoff> call  (external Touch off from Commandcnc)
  G1  X-0.223 Y2.355
  G0  Z0.090
  M3 S100
  G4 P0.4
  G1 Z0.060 F115.0
  M67 E0 Q20 (DTHC is on)
  G3 X-0.015 Y2.563 I0.000 J0.208 F190.0
  G2 X0.250 Y2.828 I0.265 J-0.000
  G1 X5.938
  G3 X5.985 Y2.875 I-0.000 J0.048
  G1 Y6.250
  G2 X6.250 Y6.515 I0.265 J-0.000
  G1 X9.485
  Y8.750
  G2 X9.750 Y9.015 I0.265 J0.000
  G1 X27.125
  G2 X27.390 Y8.750 I0.000 J-0.265
  G1 Y6.515
  X30.625
  G2 X30.890 Y6.250 I0.000 J-0.265
  G1 Y2.875
  G3 X30.937 Y2.828 I0.048 J-0.000
  G1 X36.625
  G2 X36.890 Y2.563 I0.000 J-0.265
  G1 Y0.000
  G2 X36.875 Y-0.015 I-0.015 J-0.000
  G1 X-0.000
  G2 X-0.015 Y0.000 I0.000 J0.015
  G1 Y2.563
  (Part: 16437-43 COFFEE SNACK CADDY BODY Duplicate 1)
  G3 X-0.223 Y2.771 I-0.208 J0.000
  G0 X-0.222 Y2.772 (Add tiny extension)
  M5
  o<endcut> call
  M68 E0 Q10 (DTHC is OFF)
  G4 P.1
  G4 P0.5
  (Operation: Outside Offset, STEEL, T107: 45A FINE CUT HIGH SPEED CARBON STEEL 16 GA)
  G0  X-0.223 Y2.771 Z2.000
  Y11.855
  G0 Z0.50
  o<touchoff> call  (external Touch off from Commandcnc)
  G1  X-0.223 Y11.855
  G0  Z0.090
  M3 S100
  G4 P0.4
  G1 Z0.060 F115.0
  M67 E0 Q20 (DTHC is on)
  G3 X-0.015 Y12.063 I0.000 J0.208 F190.0
  G2 X0.250 Y12.328 I0.265 J-0.000
  G1 X5.938
  G3 X5.985 Y12.375 I-0.000 J0.048
  G1 Y15.750
  G2 X6.250 Y16.015 I0.265 J-0.000
  G1 X9.485
  Y18.250
  G2 X9.750 Y18.515 I0.265 J0.000
  G1 X27.125
  G2 X27.390 Y18.250 I0.000 J-0.265
  G1 Y16.015
  X30.625
  G2 X30.890 Y15.750 I0.000 J-0.265
  G1 Y12.375
  G3 X30.937 Y12.328 I0.048 J-0.000
  G1 X36.625
  G2 X36.890 Y12.063 I0.000 J-0.265
  G1 Y9.500
  G2 X36.875 Y9.485 I-0.015 J-0.000
  G1 X-0.000
  G2 X-0.015 Y9.500 I0.000 J0.015
  G1 Y12.063
  (Part: 16437-43 COFFEE SNACK CADDY BODY Duplicate 2)
  G3 X-0.223 Y12.271 I-0.208 J0.000
  G0 X-0.222 Y12.272 (Add tiny extension)
  M5
  o<endcut> call
  M68 E0 Q10 (DTHC is OFF)
  G4 P.1
  G4 P0.5
  (Operation: Outside Offset, STEEL, T107: 45A FINE CUT HIGH SPEED CARBON STEEL 16 GA)
  G0  X-0.223 Y12.271 Z2.000
  Y21.355
  G0 Z0.50
  o<touchoff> call  (external Touch off from Commandcnc)
  G1  X-0.223 Y21.355
  G0  Z0.090
  M3 S100
  G4 P0.4
  G1 Z0.060 F115.0
  M67 E0 Q20 (DTHC is on)
  G3 X-0.015 Y21.563 I0.000 J0.208 F190.0
  G2 X0.250 Y21.828 I0.265 J-0.000
  G1 X5.938
  G3 X5.985 Y21.875 I-0.000 J0.048
  G1 Y25.250
  G2 X6.250 Y25.515 I0.265 J-0.000
  G1 X9.485
  Y27.750
  G2 X9.750 Y28.015 I0.265 J0.000
  G1 X27.125
  G2 X27.390 Y27.750 I0.000 J-0.265
  G1 Y25.515
  X30.625
  G2 X30.890 Y25.250 I0.000 J-0.265
  G1 Y21.875
  G3 X30.937 Y21.828 I0.048 J-0.000
  G1 X36.625
  G2 X36.890 Y21.563 I0.000 J-0.265
  G1 Y19.000
  G2 X36.875 Y18.985 I-0.015 J-0.000
  G1 X-0.000
  G2 X-0.015 Y19.000 I0.000 J0.015
  G1 Y21.563
  (Part: 16437-43 COFFEE SNACK CADDY BODY Duplicate 4)
  G3 X-0.223 Y21.771 I-0.208 J0.000
  G0 X-0.222 Y21.772 (Add tiny extension)
  M5
  o<endcut> call
  M68 E0 Q10 (DTHC is OFF)
  G4 P.1
  G4 P0.5
  (Operation: Outside Offset, STEEL, T107: 45A FINE CUT HIGH SPEED CARBON STEEL 16 GA)
  G0  X-0.223 Y21.771 Z2.000
  X0.171 Y31.685
  G0 Z0.50
  o<touchoff> call  (external Touch off from Commandcnc)
  G1  X0.171 Y31.685
  G0  Z0.090
  M3 S100
  G4 P0.4
  G1 Z0.060 F115.0
  M67 E0 Q20 (DTHC is on)
  G3 X0.379 Y31.893 I0.000 J0.208 F190.0
  G2 X0.644 Y32.158 I0.265 J-0.000
  G1 X6.331
  G3 X6.379 Y32.206 I-0.000 J0.048
  G1 Y35.581
  G2 X6.644 Y35.846 I0.265 J-0.000
  G1 X9.879
  Y38.081
  G2 X10.144 Y38.346 I0.265 J0.000
  G1 X27.519
  G2 X27.784 Y38.081 I0.000 J-0.265
  G1 Y35.846
  X31.019
  G2 X31.284 Y35.581 I-0.000 J-0.265
  G1 Y32.206
  G3 X31.331 Y32.158 I0.048 J-0.000
  G1 X37.019
  G2 X37.284 Y31.893 I0.000 J-0.265
  G1 Y29.331
  G2 X37.269 Y29.316 I-0.015 J0.000
  G1 X0.394
  G2 X0.379 Y29.331 I0.000 J0.015
  G1 Y31.893
  (Part: 16437-43 COFFEE SNACK CADDY BODY Duplicate 3)
  G3 X0.171 Y32.101 I-0.208 J0.000
  G0 X0.172 Y32.102 (Add tiny extension)
  M5
  o<endcut> call
  M68 E0 Q10 (DTHC is OFF)
  G4 P.1
  G4 P0.5
  (Operation: Outside Offset, STEEL, T107: 45A FINE CUT HIGH SPEED CARBON STEEL 16 GA)
  G0  X0.171 Y32.101 Z2.000
  X40.898 Y37.334
  G0 Z0.50
  o<touchoff> call  (external Touch off from Commandcnc)
  G1  X40.898 Y37.334
  G0  Z0.090
  M3 S100
  G4 P0.4
  G1 Z0.060 F115.0
  M67 E0 Q20 (DTHC is on)
  G3 X41.106 Y37.126 I0.208 J-0.000 F190.0
  G2 X41.371 Y36.861 I-0.000 J-0.265
  G1 Y31.173
  G3 X41.419 Y31.126 I0.048 J0.000
  G1 X44.794
  G2 X45.059 Y30.861 I0.000 J-0.265
  G1 Y27.626
  X47.294
  G2 X47.559 Y27.361 I0.000 J-0.265
  G1 Y9.986
  G2 X47.294 Y9.721 I-0.265 J0.000
  G1 X45.059
  Y6.486
  G2 X44.794 Y6.221 I-0.265 J0.000
  G1 X41.419
  G3 X41.371 Y6.173 I-0.000 J-0.048
  G1 Y0.486
  G2 X41.106 Y0.221 I-0.265 J0.000
  G1 X38.544
  G2 X38.529 Y0.236 I0.000 J0.015
  G1 Y37.111
  G2 X38.544 Y37.126 I0.015 J0.000
  G1 X41.106
  G3 X41.314 Y37.334 I0.000 J0.208
  G0 X41.315 Y37.335 (Add tiny extension)
  M5
  o<endcut> call
  M68 E0 Q10 (DTHC is OFF)
  G4 P.1
  G4 P0.5
  G0  X41.314 Y37.334 Z2.000
  X0.000 Y0.000
  M68 E0 Q900
  G4 P.2
  M68 E0 Q10 (DTHC is off)
  M5 M30