Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 1.1.4 (Aug 12 2014 - 15:21:46)
- U-boot dni29 V0.5 for DNI HW ID: 29764821 NOR flash 2MB NAND flash 128MB RAM 128MB
- - Dragonfly 1.0DRAM:
- sri
- ath_ddr_initial_config(278): (ddr2 init)
- ath_sys_frequency: cpu 775 ddr 650 ahb 258
- Tap values = (0x10, 0x10, 0x10, 0x10)
- 128 MB
- Top of RAM usable for U-Boot at: 88000000
- Reserving 265k for U-Boot at: 87fbc000
- Reserving 192k for malloc() at: 87f8c000
- Reserving 44 Bytes for Board Info at: 87f8bfd4
- Reserving 36 Bytes for Global Data at: 87f8bfb0
- Reserving 128k for boot params() at: 87f6bfb0
- Stack Pointer at: 87f6bf98
- Now running in RAM - U-Boot at: 87fbc000
- Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x15
- flash size 2MB, sector count = 32
- Flash: 2 MB
- Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014 Qualcomm Atheros Inc.
- ath_parse_read_id: SPI NAND V.Id: 0xc8 D.Id: 0xf1
- ====== NAND Parameters ======
- sc = 0x87ff77e4 page = 0x800 block = 0x20000In: serial
- Out: serial
- Err: serial
- Net: ath_gmac_enet_initialize...
- Fetching MAC Address from 0x87fe914c
- ath_gmac_enet_initialize: reset mask:c02200
- athr_mgmt_init ::done
- Dragonfly ----> S17 PHY *
- athrs17_reg_init: complete
- SGMII in forced mode
- athr_gmac_sgmii_setup SGMII done
- : cfg1 0x80000000 cfg2 0x7114
- eth0: xx:xx:xx:xx:xx:xx
- eth0 up
- eth0
- Setting 0x181162c0 to 0x48902100
- Hit any key to stop autoboot: 0
- Trying eth0
- dup 1 speed 1000
- Client starts...[Listening] for ADVERTISE...TTT
- Retry count exceeded; boot the image as usual
- nmrp server is stopped or failed !
- Loading from device 0: ath-spi-nand (offset 0x0)
- [0x1800] is corrected by ECC
- [0x16800] is corrected by ECC
- [0x20800] is corrected by ECC
- [0xd2000] is corrected by ECC
- [0xf4800] is corrected by ECC
- [0x103800] is corrected by ECC
- [0x111000] is corrected by ECC
- [0x147800] is corrected by ECC
- [0x172800] is corrected by ECC
- [0x179000] is corrected by ECC
- [0x1f5800] is corrected by ECC
- [0x23c800] is corrected by ECC
- [0x253800] is corrected by ECC
- [0x2b1000] is corrected by ECC
- [0x3ca800] is corrected by ECC
- [0x3e7800] is corrected by ECC
- [0x403000] is corrected by ECC
- [0x449000] is corrected by ECC
- [0x484000] is corrected by ECC
- [0x4a4800] is corrected by ECC
- [0x4b3000] is corrected by ECC
- [0x4c4800] is corrected by ECC
- [0x4c5800] is corrected by ECC
- [0x4d0000] is corrected by ECC
- [0x4e3000] is corrected by ECC
- [0x557800] is corrected by ECC
- [0x5a5000] is corrected by ECC
- [0x5bf000] is corrected by ECC
- [0x610000] is corrected by ECC
- [0x61d000] is corrected by ECC
- [0x65b000] is corrected by ECC
- [0x678000] is corrected by ECC
- [0x67a000] is corrected by ECC
- [0x67b800] is corrected by ECC
- [0x689800] is corrected by ECC
- [0x69b800] is corrected by ECC
- [0x6a6800] is corrected by ECC
- [0x6c5000] is corrected by ECC
- [0x767000] is corrected by ECC
- [0x789800] is corrected by ECC
- [0x796000] is corrected by ECC
- [0x7cb000] is corrected by ECC
- [0x7dd000] is corrected by ECC
- [0x826000] is corrected by ECC
- [0x841800] is corrected by ECC
- [0x852800] is corrected by ECC
- [0x896800] is corrected by ECC
- [0x897000] is corrected by ECC
- [0x8c5800] is corrected by ECC
- [0x904000] is corrected by ECC
- [0x91a000] is corrected by ECC
- [0x924000] is corrected by ECC
- [0x937800] is corrected by ECC
- [0x989800] is corrected by ECC
- [0x98f000] is corrected by ECC
- [0x991000] is corrected by ECC
- [0x9ce800] is corrected by ECC
- [0x9e3000] is corrected by ECC
- [0x9f7000] is corrected by ECC
- [0xa32800] is corrected by ECC
- [0xa62800] is corrected by ECC
- [0xa88800] is corrected by ECC
- [0xa8f000] is corrected by ECC
- [0xacc800] is corrected by ECC
- [0xace800] is corrected by ECC
- [0xacf800] is corrected by ECC
- [0xb5a800] is corrected by ECC
- [0xb5c000] is corrected by ECC
- [0xb5c800] is corrected by ECC
- [0xb5f000] is corrected by ECC
- [0xb96000] is corrected by ECC
- [0xbcf000] is corrected by ECC
- [0xbda000] is corrected by ECC
- [0xc06000] is corrected by ECC
- [0xc5d000] is corrected by ECC
- [0xc65000] is corrected by ECC
- [0xc73000] is corrected by ECC
- [0xc7b800] is corrected by ECC
- [0xc95000] is corrected by ECC
- [0xcf1800] is corrected by ECC
- [0xcf6800] is corrected by ECC
- [0xcf9800] is corrected by ECC
- ** check kernel image **
- Verifying Checksum ... OK
- ** check rootfs image **
- Verifying Checksum ... OK
- ## Booting image at 81000000 ...
- Image Name: MIPS OpenWrt Linux-2.6.31
- Created: 2014-11-17 10:12:03 UTC
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1159942 Bytes = 1.1 MB
- Load Address: 80002000
- Entry Point: 8027d970
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 8027d970) ...
- ## Giving linux memsize in bytes, 134217728
- Starting kernel ...
- Booting QCA956x
- Linux version 2.6.31 (root@dnixm-compiler3) (gcc version 4.3.3 (GCC) ) #1 Mon Nov 17 18:11:47 CST 2014
- flash_size passed from bootloader = 2
- CPU revision is: 00019750 (MIPS 74Kc)
- ath_sys_frequency: cpu 775 ddr 650 ahb 258
- Determined physical RAM map:
- memory: 08000000 @ 00000000 (usable)
- Initrd not found or empty - disabling initrd
- Zone PFN ranges:
- Normal 0x00000000 -> 0x00008000
- Movable zone start PFN for each node
- early_node_map[1] active PFN ranges
- 0: 0x00000000 -> 0x00008000
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
- Kernel command line: console=ttyS0,115200 rootfstype=squashfs board=WNDR4500v3 mtdparts=ath-nor0:256k(u-boot)ro,64k(u-boot-env)ro,64k(caldata_backup),64k(config),64k(traffic_meter),64k(pot),1408k(reserved),64k(caldata);ath-spi-nand:1152k(kernel),24448k(rootfs),25600k@0x0(firmware),2048k(language),128k(mtdoops),-(reserved)
- PID hash table entries: 512 (order: 9, 2048 bytes)
- Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
- Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
- Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
- Writing ErrCtl register=00000000
- Readback ErrCtl register=00000000
- Memory: 126264k/131072k available (2574k kernel code, 4628k reserved, 661k data, 152k init, 0k highmem)
- SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- NR_IRQS:128
- plat_time_init: plat time init done
- r4k_clockevent_init: Ignoring int_usable failure
- Calibrating delay loop... 387.07 BogoMIPS (lpj=774144)
- Mount-cache hash table entries: 512
- NET: Registered protocol family 16
- ath_pcibios_init: bus 0
- ath_pcibios_init(254): PCI 0 CMD write: 0x356
- registering PCI controller with io_map_base unset
- bio: create slab <bio-0> at 0
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- pci 0000:00:00.0: PME# supported from D0 D1 D3hot
- pci 0000:00:00.0: PME# disabled
- pcibios_map_irq: IRQ 76 for bus 0
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 4096 (order: 3, 32768 bytes)
- TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
- TCP: Hash tables configured (established 4096 bind 4096)
- TCP reno registered
- NET: Registered protocol family 1
- ATH GPIOC major 0
- squashfs: version 4.0 (2009/01/31) Phillip Lougher
- JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
- msgmni has been set to 246
- io scheduler noop registered
- io scheduler deadline registered (default)
- Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
- serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
- console [ttyS0] enabled
- tun: Universal TUN/TAP device driver, 1.6
- tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- 8 cmdlinepart partitions found on MTD device ath-nor0
- Creating 8 MTD partitions on "ath-nor0":
- 0x000000000000-0x000000040000 : "u-boot"
- 0x000000040000-0x000000050000 : "u-boot-env"
- 0x000000050000-0x000000060000 : "caldata_backup"
- 0x000000060000-0x000000070000 : "config"
- 0x000000070000-0x000000080000 : "traffic_meter"
- 0x000000080000-0x000000090000 : "pot"
- 0x000000090000-0x0000001f0000 : "reserved"
- 0x0000001f0000-0x000000200000 : "caldata"
- Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014 Qualcomm Atheros Inc.
- ath_parse_read_id: SPI NAND V.Id: 0xc8 D.Id: 0xf1
- 6 cmdlinepart partitions found on MTD device ath-spi-nand
- Creating 6 MTD partitions on "ath-spi-nand":
- 0x000000000000-0x000000120000 : "kernel"
- 0x000000120000-0x000001900000 : "rootfs"
- mtd: find squashfs magic at 0x120000 of "ath-spi-nand"
- the correct location of partition "rootfs": 0x000000120000-0x000001900000
- mtd: partition "rootfs" set to be root filesystem
- mtd: partition "rootfs_data" created automatically, ofs=D80000, len=B80000
- 0x000000d80000-0x000001900000 : "rootfs_data"
- 0x000000000000-0x000001900000 : "firmware"
- 0x000001900000-0x000001b00000 : "language"
- 0x000001b00000-0x000001b20000 : "mtdoops"
- 0x000001b20000-0x000008000000 : "reserved"
- ====== NAND Parameters ======
- sc = 0x87851800 page = 0x800 block = 0x20000
- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- Port Status 1c000004
- ath-ehci ath-ehci.0: ATH EHCI
- ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
- ehci_reset Intialize USB CONTROLLER in host mode: 13
- ehci_reset Port Status 1c000000
- ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
- ehci_reset Intialize USB CONTROLLER in host mode: 13
- ehci_reset Port Status 1c000000
- ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
- usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- usb usb1: Product: ATH EHCI
- usb usb1: Manufacturer: Linux 2.6.31 ehci_hcd
- usb usb1: SerialNumber: platform
- usb usb1: configuration #1 chosen from 1 choice
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- Port Status 1c000000
- ath-ehci1 ath-ehci1.1: ATH EHCI
- ath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2
- ehci_reset Intialize USB CONTROLLER in host mode: 13
- ehci_reset Port Status 1c000000
- ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000
- ehci_reset Intialize USB CONTROLLER in host mode: 13
- ehci_reset Port Status 1c000000
- ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00
- usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
- usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- usb usb2: Product: ATH EHCI
- usb usb2: Manufacturer: Linux 2.6.31 ehci_hcd
- usb usb2: SerialNumber: platform
- usb usb2: configuration #1 chosen from 1 choice
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 1 port detected
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- Netfilter messages via NETLINK v0.30.
- NAT Session Management application ports priority table is loaded!
- nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
- ip_tables: (C) 2000-2006 Netfilter Core Team
- TCP cubic registered
- NET: Registered protocol family 10
- ip6_tables: (C) 2000-2006 Netfilter Core Team
- IPv6 over IPv4 tunneling driver
- NET: Registered protocol family 17
- Ebtables v2.0 registered
- 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
- All bugs added by David S. Miller <davem@redhat.com>
- arch/mips/atheros/gpio.c (ath_simple_config_init) JUMPSTART_GPIO: 12
- arch/mips/atheros/gpio.c (ath_simple_config_init) ATH_S17INT_GPIO: 10
- athwdt_init: Registering WDT success
- VFS: Mounted root (squashfs filesystem) readonly on device 31:9.
- Freeing unused kernel memory: 152k freed
- Please be patient, while OpenWrt loads ...
- - init -
- init started: BusyBox v1.4.2 (2014-11-17 17:34:23 CST) multi-call binary
- Loading data from /dev/mtd3 ...
- Done!
- The data center is Running ...
- board parameter in mtd7 and mtd2 partition are same and valid
- PPP generic driver version 2.4.2
- dni-lan-qos module init.
- dni-qos module init.
- NET: Registered protocol family 24
- nf_nat_STARCRAFT: module license 'unspecified' taints kernel.
- Disabling lock debugging due to kernel taint
- nf_conntrack_rtsp v0.6.21 loading
- nf_nat_rtsp v0.6.21 loading
- nf_conntrack_proto_esp loaded
- NET: Registered protocol family 27
- PPPoL2TP kernel driver, V0.16.1
- PPTP-GRE-v1.13 2007 (C) Delta Networks Inc.
- qca956x_GMAC: Length per segment 1536
- 956x_GMAC: qca956x_gmac_attach
- 956x_GMAC: qca956x_set_gmac_caps
- Currently in interrupt mode unit0
- qca956x_set_gmac_caps CHECK DMA STATUS
- mac:0 Registering S17....
- qca956x_GMAC: RX TASKLET - Pkts per Intr:160
- qca956x_GMAC: Mac address for unit 0:bf1f0000
- qca956x_GMAC: c0:ff:d4:d3:98:7e
- qca956x_GMAC: Max segments per packet : 1
- qca956x_GMAC: Max tx descriptor count : 128
- qca956x_GMAC: Max rx descriptor count : 224
- qca956x_GMAC: Mac capability flags : 12002401
- 956x_GMAC: Serdes PLL is locked value 0x1b838116
- Generating Rules...
- Done!
- SN: XXXXXXXXXXXX
- WAN MAC: xx:xx:xx:xx:xx:xx
- LAN MAC: xx:xx:xx:xx:xx:xx
- WLA MAC: xx:xx:xx:xx:xx:xx
- The region number is: 0x0002
- REGION: WW
- client bridge loaded
- cp: cannot stat '/etc/wpa2.orig/*': No such file or directory
- To set s17 LOOKUP_CTRL_REG registers, flag 0
- athr_gmac_ring_alloc Allocated 2048 at 0x8791b800
- sram_desc_cnt 1536,mac Unit 0,Tx r->ring_desc 0xbd000000
- athr_gmac_ring_alloc Allocated 3584 at 0x87be5000
- sram_desc_cnt 4224,mac Unit 0,Rx r->ring_desc 0xbd000600
- 956x_GMAC: eth0 in SGMII MODE
- Dragonfly ----> S17 PHY *
- /proc/qca_switch/nf_athrs17_hnat is created
- /proc/qca_switch/nf_athrs17_hnat_wan_type is created
- /proc/qca_switch/nf_athrs17_hnat_ppp_id is created
- /proc/qca_switch/nf_athrs17_hnat_udp_thresh is created
- /proc/qca_switch/nf_athrs17_hnat_wan_ip is created
- /proc/qca_switch/nf_athrs17_hnat_ppp_peer_ip is created
- /proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created
- /proc/qca_switch/nf_athrs17_hnat_wan_mac is created
- /proc/qca_switch/nf_athrs17_hnat_ppp_id2 is created
- /proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created
- Registering IPv6 hooks...
- Adding ACL rules 15 - upnp_ssdp_add_acl_rules
- ACL is not yet enabled. Enabling...
- Adding ACL rules 8 - ipv6_snooping_solicted_node_add_acl_rules
- Adding ACL rules 12 - ipv6_snooping_sextuple0_group_add_acl_rules
- Adding ACL rules 14 - ipv6_snooping_quintruple0_1_group_add_acl_rules
- Hello, nat helper module for 1.1!
- ######## S17 SSDK init succeeded! ########
- athrs17_reg_init:done
- 955x_SGMII::athr_gmac_sgmii_setup Done
- Setting Drop CRC Errors, Pause Frames and Length Error frames
- Setting PHY...
- Phy setup Complete
- To set s17 LOOKUP_CTRL_REG registers, flag 1
- ADDRCONF(NETDEV_UP): phy0: link is not ready
- athr_gmac_ring_free Freeing at 0x8791b800
- athr_gmac_ring_free Freeing at 0x87be5000
- Write Reg: 0x00000620: Oldval = 0x089004f0 Newval = 0x080004f0
- Write Reg: 0x00000660: Oldval = 0x0014007e Newval = 0x0014017e
- Write Reg: 0x0000066c: Oldval = 0x0014007d Newval = 0x0014017d
- Write Reg: 0x00000678: Oldval = 0x0014007b Newval = 0x0014017b
- Write Reg: 0x00000684: Oldval = 0x00140077 Newval = 0x00140177
- Write Reg: 0x00000690: Oldval = 0x0014006f Newval = 0x0014016f
- Write Reg: 0x0000069c: Oldval = 0x0014005f Newval = 0x0014015f
- Write Reg: 0x00000c00: Oldval = 0x00000003 Newval = 0x00000002
- Write Reg: 0x00000420: Oldval = 0x00010001 Newval = 0x00010001
- Write Reg: 0x00000424: Oldval = 0x00003040 Newval = 0x00002040
- Write Reg: 0x00000428: Oldval = 0x00010001 Newval = 0x00010001
- Write Reg: 0x0000042c: Oldval = 0x00003040 Newval = 0x00001040
- Write Reg: 0x00000430: Oldval = 0x00010001 Newval = 0x00010001
- Write Reg: 0x00000434: Oldval = 0x00003040 Newval = 0x00001040
- Write Reg: 0x00000438: Oldval = 0x00010001 Newval = 0x00010001
- Write Reg: 0x0000043c: Oldval = 0x00003040 Newval = 0x00001040
- Write Reg: 0x00000440: Oldval = 0x00010001 Newval = 0x00010001
- Write Reg: 0x00000444: Oldval = 0x00003040 Newval = 0x00001040
- Write Reg: 0x00000448: Oldval = 0x00010001 Newval = 0x00020001
- Write Reg: 0x0000044c: Oldval = 0x00003040 Newval = 0x00001040
- Write Reg: 0x000To set s17 LOOKUP_CTRL_REG registers, flag 0
- 00614: Oldval = athr_gmac_ring_alloc Allocated 2048 at 0x87193800
- 0x00000000 Newvasram_desc_cnt 4224,mac Unit 0,Tx r->ring_desc 0xbd000000
- l = 0x80000001
- athr_gmac_ring_alloc Allocated 3584 at 0x87be5000
- Write Reg: 0x000sram_desc_cnt 4224,mac Unit 0,Rx r->ring_desc 0xbd000600
- 00610: Oldval = 0x00000000 Newva956x_GMAC: eth0 in SGMII MODE
- l = 0x001bd560
- Dragonfly ----> S17 PHY *
- Write Reg: 0x00000614: Oldval = 0x00000001 Newval = 0x80010002
- Write Reg: 0x00000610: Oldval = Error: cannot be initialized twice!
- 0x00000000 Newvaathrs17_reg_init:done
- l = 0x001b7fe0
- 955x_SGMII::athr_gmac_sgmii_setup Done
- Write Reg: 0x000Setting Drop CRC Errors, Pause Frames and Length Error frames
- 00614: Oldval = Setting PHY...
- 0x00000002 Newval = 0x80020002
- Write Reg: 0x00000090: Oldval = 0x00000000 Newval = 0x00001280
- Write Reg: 0x00000624: Oldval = 0x007f7f7f Newval = 0x7f7f7f7f
- Write Reg: 0x00000210: Oldval = 0x20202000 Newval = 0x26262606
- Write Reg: 0x00000214: Oldval = 0x00002020 Newval = 0x01002026
- Phy setup Complete
- To set s17 LOOKUP_CTRL_REG registers, flag 1
- ADDRCONF(NETDEV_UP): phy0: link is not ready
- init.enet: Default WAN MAC is : xx:xx:xx:xx:xx:xx
- device eth0 entered promiscuous mode
- device phy0 entered promiscuous mode
- init.enet: Default LAN MAC is : xx:xx:xx:xx:xx:xx
- Loading DNI-ENET driver
- device pas0 entered promiscuous mode
- Enet:0 port3 up
- 956x_GMAC: Enet Unit:0 PHY:3 is UP eth0 SGMII 1000Mbps full duplex
- 956x_GMAC: done cfg2 0x7235 ifctl 0x0 miictrl
- 955x_SGMII::athr_gmac_sgmii_setup Done
- Setting Drop CRC Errors, Pause Frames and Length Error frames
- ADDRCONF(NETDEV_CHANGE): phy0: link becomes ready
- br0: port 1(eth0) entering forwarding state
- br0: port 1(eth0) entering disabled state
- br0: port 1(eth0) entering forwarding state
- SSDK Init OK!
- operate done.
- udhcp server (v0.9.8) started
- Enet:0 port:3 down
- 956x_GMAC:unit 0: phy 3 not up carrier 1
- br0: port 1(eth0) entering disabled state
- The attached devices demo is Running ...
- The telnetenable is running ...
- Deleting static route ... Done!
- Adding static route ... Done!
- Enet:0 port3 up
- 956x_GMAC: Enet Unit:0 PHY:3 is UP eth0 SGMII 1000Mbps full duplex
- 956x_GMAC: done cfg2 0x7235 ifctl 0x0 miictrl
- 955x_SGMII::athr_gmac_sgmii_setup Done
- Setting Drop CRC Errors, Pause Frames and Length Error frames
- br0: port 1(eth0) entering forwarding state
- dni-qos attached on eth1.
- br0: port 1(eth0) entering disabled state
- dni-qos attached on br0.
- br0: port 1(eth0) entering forwarding state
- udhcp client (v0.9.8) started
- time zone index is : 0
- Run NTP Client with setting: pri:time-g.netgear.com sec:time-h.netgear.com
- no 6RD parameters available, so unset 6rd related config
- killall: miniupnpd: no process killed
- killall: pppd: no process killed
- Deleting static route ... Done!
- Deleting static route ... Done!
- Adding static route ... Done!
- start rip process
- start initial data
- Sending discover...
- Jan 1 00:00:28 miniupnpd[944]: listening on 192.168.1.1:5555
- No user name for DDNS!
- syslogd can't open the temp log file: /tmp/log/log-message or /var/log/messages
- Starting Firewall...
- Done!
- The region number is: 0x0002
- REGION: WW
- Generating RSA private key, 1024 bit long modulus
- ufsd:: trace mask set to 0000000f
- ufsd: driver (lke_9.0.0 lke_9.0.0_r233352_b3, LBD=ON, acl, ioctl, bdi, sd(0), wb, bz, tr) loaded at 87380000
- NTFS support included
- Big endian platform
- optimized: speed
- Build_for__NETGEAR_WNDR4500V3_k2.6.31_2014-06-18_lke_9.0.0_r233352_b3
- kcg 333 :GPL NetUSB up!
- kc 90 : run_telnetDBGDServer start
- kc 227 : init_DebugD end
- INFO1802: NetUSB 1.02.53, 0002061F : Jun 19 2014 11:29:41
- INFO1804: 7423: WNDR4500v3 :WNDR4500v3
- INFO1805: AUTH ISOC
- INFO1806: MOVE_HEAD filterAudio
- usbcore: registered new interface driver KC NetUSB General Driver
- INFO0ADC: --- checkSBusTimeoutThread start ---
- INFO0145: init proc : PAGE_SIZE 4096
- INFO16D6: infomap 8734bef0
- INFO16D9: sleep to wait br0 to wake up
- INFO02CE: use dev Name br0
- INFO16E2: sleep to wait br0 end.
- INFO16FB: UDP_BROAD 7423 tcpPort:625868800
- INFO02CE: use dev Name br0
- INFO15DF: tcpConnector() started...
- Changing password for admin
- New password:Generating selfsigned certificate with subject 'C=DE;ST=Saxony;L=Leipzig;CN=OpenWrt;' and validity 2001-09-09 01:46:40-2003-09-09 01:46:40
- AUTO FW CHECK: power cycle
- /etc/rc.common: /etc/rc.common: 117: detplc: not found
- FW checking ...
- week_day == 1
- POT is Running...
- The POT-(Get/Set) Demo is Running ...
- Sending discover...
- ADDRCONF(NETDEV_UP): sit0: link is not ready
- ADDRCONF(NETDEV_UP): pas0: link is not ready
- Bad password: too weak
- Retype password:
- Password for admin changed by root
- killall: smbd: no process killed
- killall: smbd: no process killed
- killall: nmbd: no process killed
- USB Storage daemon is Running ...
- Changing password for admin
- New password:INFO14BC: Bind to br0
- Bad password: too weak
- Retype password:
- Password for admin changed by root
- [USB-AFP]: Total 0 partitions are FOUND!
- killall: avahi-daemon: no process killed
- [USB-AFP]: Loading USB share information ......diskname: (null)
- cat: /var/run/afpd.pid: No such file or directory
- Args: 1
- ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D)
- ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
- ath_dfs: Version 2.0.0
- Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
- ath_tx99: Version 2.0
- Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved
- Sending discover...
- ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
- ath_ahb: 10.2-00085-8 (Atheros/multi-bss)
- __ath_attach: Set global_scn[0]
- *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead ***
- ACBKMinfree = 48
- ACBEMinfree = 32
- ACVIMinfree = 16
- ACVOMinfree = 0
- CABMinfree = 48
- UAPSDMinfree = 0
- ATH_TXBUF=540
- Enterprise mode: 0x03bda000
- Restoring Cal data from Flash
- Green-AP : Green-AP : Attached
- ath_get_caps[6148] rx chainmask mismatch actual 3 sc_chainmak 0
- ath_get_caps[6123] tx chainmask mismatch actual 3 sc_chainmak 0
- ath_attach_dfs[12558] dfsdomain 1
- ath_tx_paprd_init sc 870e0000 PAPRD disabled in HAL
- SC Callback Registration for wifi0
- wifi0: Atheros 956X: mem=0xb8100000, irq=2
- ath_pci: 10.2-00085-8 (Atheros/multi-bss)
- __ath_attach: Set global_scn[1]
- *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead ***
- ACBKMinfree = 48
- ACBEMinfree = 32
- ACVIMinfree = 16
- ACVOMinfree = 0
- CABMinfree = 48
- UAPSDMinfree = 0
- ATH_TXBUF=540
- Restoring Cal data from Flash
- Green-AP : Green-AP : Attached
- ath_get_caps[6148] rx chainmask mismatch actual 7 sc_chainmak 0
- ath_get_caps[6123] tx chainmask mismatch actual 7 sc_chainmak 0
- ath_attach_dfs[12558] dfsdomain 1
- ath_tx_paprd_init sc 870d0000 PAPRD disabled in HAL
- SC Callback Registration for wifi1
- wifi1: Atheros ???: mem=0x12000000, irq=76 hw_base=0xb2000000
- ath_attach_dfs[12558] dfsdomain 1
- ath_attach_dfs[12558] dfsdomain 1
- Creating ap for NETGEAR68 on
- wlan_vap_create : enter. devhandle=0x865602c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
- wlan_vap_create : exit. devhandle=0x865602c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
- VAP device ath0 created
- Added ath0 mode master
- Invalid command : bgscan
- Interface doesn't accept private ioctl...
- HALDbg (8BE0): Operation not permitted
- Interface doesn't accept private ioctl...
- ForBiasAuto (8BE0): Operation not permitted
- DES SSID SET=NETGEAR68
- ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
- Set freq vap stop send + 854b8000
- Set freq vap stop send -854b8000
- Set wait done --854b8000
- /etc/ath/makeVAP: /etc/ath/makeVAP: 492: cannot create /proc/sys/dev/ath/htdupieenable: Directory nonexistent
- WARNING: Fragmentation with HT mode NOT ALLOWED!!
- Error for wireless request "Set Fragmentation Threshold" (8B24) :
- SET failed on device ath0 ; Invalid argument.
- Invalid command : setVowExt
- Invalid command : setKeySrchAlways
- Invalid command : set_vsp_enable
- Invalid command : setPhyRestartWar
- Invalid command : setVowExtStats
- sc nodebug 0
- Created ath0 mode ap for NETGEAR68
- lo no wireless extensions.
- sit0 no wireless extensions.
- phy0 no wireless extensions.
- br0 no wireless extensions.
- eth0 no wireless extensions.
- eth1 no wireless extensions.
- pas0 no wireless extensions.
- wifi0 no wireless extensions.
- wifi1 no wireless extensions.
- Modules already loaded
- Creating ap for NETGEAR68-5G on
- wlan_vap_create : enter. devhandle=0x85f902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
- wlan_vap_create : exit. devhandle=0x85f902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
- VAP device ath1 created
- Added ath1 mode master
- Invalid command : bgscan
- Interface doesn't accept private ioctl...
- HALDbg (8BE0): Operation not permitted
- Invalid command : extoffset
- DES SSID SET=NETGEAR68-5G
- ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
- Set freq vap stop send + 85804000
- Set freq vap stop send -85804000
- Set wait done --85804000
- /etc/ath/makeVAP: /etc/ath/makeVAP: 492: cannot create /proc/sys/dev/ath/htdupieenable: Directory nonexistent
- WARNING: Fragmentation with HT mode NOT ALLOWED!!
- Error for wireless request "Set Fragmentation Threshold" (8B24) :
- SET failed on device ath1 ; Invalid argument.
- Invalid command : setVowExt
- Invalid command : setKeySrchAlways
- Invalid command : set_vsp_enable
- Invalid command : setPhyRestartWar
- Invalid command : setVowExtStats
- sc nodebug 0
- Created ath1 mode ap for NETGEAR68-5G
- lo no wireless extensions.
- sit0 no wireless extensions.
- phy0 no wireless extensions.
- br0 no wireless extensions.
- eth0 no wireless extensions.
- eth1 no wireless extensions.
- pas0 no wireless extensions.
- wifi0 no wireless extensions.
- wifi1 no wireless extensions.
- lo no wireless extensions.
- sit0 no wireless extensions.
- phy0 no wireless extensions.
- br0 no wireless extensions.
- eth0 no wireless extensions.
- eth1 no wireless extensions.
- pas0 no wireless extensions.
- device ath0 entered promiscuous mode
- wifi0 no wireless extensions.
- wifi1 no wireless extensions.
- arping: bind: Cannot assign requested address
- >>>>> WPS MODE, 2
- >>>>> WPS ENABLED, PSK
- cat: /etc/wpa2/WSC_ath0.conf: No such file or directory
- >>>>> WPS Translate, Index:0
- lo no wireless extensions.
- sit0 no wireless extensions.
- phy0 no wireless extensions.
- br0 no wireless extensions.
- eth0 no wireless extensions.
- eth1 no wireless extensions.
- pas0 no wireless extensions.
- device ath1 entered promiscuous mode
- wifi0 no wireless extensions.
- wifi1 no wireless extensions.
- arping: bind: Cannot assign requested address
- >>>>> WPS MODE, 2
- >>>>> WPS ENABLED, PSK
- cat: /etc/wpa2/WSC_ath1.conf: No such file or directory
- >>>>> WPS Translate, Index:2
- Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
- le: /etc/wpa2/WS DEVICE IS DOWN ifname=ath0
- C_ath0.conf
- DEVICE IS DOWN ifname=ath0
- ath0: Could not connect to kernel driver
- Using interface ath0 with hwaddr xx:xx:xx:xx:xx:xx and ssid 'NETGEAR68'
- random: Only 19/20 bytes of strong random data available from /dev/random
- random: Not enough entropy pool available for secure operations
- WPA: Not enough entropy in random pool for secure operations - update keys later when the first station connects
- br0: port 3(ath0) entering forwarding state
- Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
- le: /etc/wpa2/WS DEVICE IS DOWN ifname=ath1
- C_ath1.conf
- DEVICE IS DOWN ifname=ath1
- ath1: Could not connect to kernel driver
- Using interface ath1 with hwaddr xx:xx:xx:xx:xx:xx and ssid 'NETGEAR68-5G'
- random: Cannot read from /dev/random: Resource temporarily unavailable
- random: Only 19/20 bytes of strong random data available from /dev/random
- random: Not enough entropy pool available for secure operations
- WPA: Not enough entropy in random pool for secure operations - update keys later when the first station connects
- br0: port 4(ath1) entering forwarding state
- traffic_meter start : .
- killall: igmpproxy: no process killed
- mtdoops: Attached to MTD device 13 name mtdoops
- Boot up procedure is Finished!!!
- Please press Enter to activate this console. No lease, forking to background.
- mlme_create_infra_bss : Overriding HT40 channel with HT20 channel
- Sending discover...
- Sending discover...
- Sending discover...
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement