Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 1.1.3 (Jul 16 2010 - 11:25:10) (ALPHA)
- SVN revision: 359
- Target board: WRG-ND08
- Board: Ralink APSoC DRAM: 32 MB
- Flash: Bank 0, ID:000322a8, Size 4194304 (0x00400000)
- ============================================
- Ralink UBoot Version: 3.3
- --------------------------------------------
- ASIC 3883_MP (MAC to MAC 100F MII Mode)
- DRAM component: 256 Mbits SDR
- DRAM bus: 16 bit
- Total memory: 32 MBytes
- Flash component: NOR Flash
- Date:Jul 16 2010 Time:11:25:10
- ============================================
- icache: sets:512, ways:4, linesz:32 ,total:65536
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- GPIO pin 24 reset to switch
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- You choosed 1
- 0
- 1: System Load Linux to SDRAM via TFTP.
- Please Input new ones /or Ctrl-C to discard
- Input device IP (192.168.2.1) ==:192.168.2.11
- Input server IP (192.168.2.100) ==:192.168.2.100
- Input Linux Kernel filename (815su.bin) ==:815su.bin n
- 1.set ge1 as normal mode
- 1.set ge1 as mii mode
- enable turbo mii
- Using Eth0 (10/100-M) device
- TFTP from server 192.168.2.100; our IP address is 192.168.2.1
- Filename '815su.bin'.
- Loading: *checksum bad
- checksum bad
- checksum bad
- checksum bad
- checksum bad
- checksum bad
- checksum bad
- checksum bad
- T #################################################################
- #################################################################
- #################################################################
- ####################################Got ARP REQUEST, return our IP
- #############################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- ########################################## done
- Bytes transferred = 3539114 (3600aa hex)
- Automatic boot of image at addr 0x80800000 ...
- ## Booting image at 80800000 ...
- We have SEAMA, Image Size = 3509510
- Verifying Checksum ...
- Uncompressing SEAMA linux.lzma ... OK
- ## Transferring control to Linux (at address 8080000c) ...
- ## Giving linux memsize in MB, 32
- Starting kernel ...
- [ 0.000000] Linux version 4.4.39 (bracco@bracco-VirtualBox) (gcc version 5.4.0 (LEDE GCC 5.4.0 r2669-236bf83) ) #0 Sat Dec 24 11:10:37 2016
- [ 0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
- [ 0.000000] MIPS: machine is D-Link DIR-815 A1
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 02000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
- [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Writing ErrCtl register=00000000
- [ 0.000000] Readback ErrCtl register=00000000
- [ 0.000000] Memory: 28288K/32768K available (2911K kernel code, 129K rwdata, 712K rodata, 144K init, 195K bss, 4480K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] CPU Clock: 500MHz
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
- [ 0.000012] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
- [ 0.015486] Calibrating delay loop... 249.44 BogoMIPS (lpj=1247232)
- [ 0.090661] pid_max: default: 32768 minimum: 301
- [ 0.100000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.113023] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.135135] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.154879] pinctrl core: initialized pinctrl subsystem
- [ 0.166122] NET: Registered protocol family 16
- [ 0.180436] rt3883-pci 10140000.pci: mode: PCIe
- [ 1.780161] PCI host bridge /pci@10140000/host-bridge ranges:
- [ 1.791499] MEM 0x0000000020000000..0x000000002fffffff
- [ 1.801846] IO 0x0000000010160000..0x000000001016ffff
- [ 1.827139] rt2880_gpio 10000600.gpio: registering 24 gpios
- [ 1.838225] rt2880_gpio 10000600.gpio: registering 24 irq handlers
- [ 1.850701] rt2880_gpio 10000638.gpio: registering 16 gpios
- [ 1.862849] PCI host bridge to bus 0000:00
- [ 1.870863] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
- [ 1.884600] pci_bus 0000:00: root bus resource [io 0xffffffff]
- [ 1.896307] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
- [ 1.909804] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 1.926152] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 1.942871] pci 0000:00:01.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
- [ 1.956297] pci 0000:00:01.0: BAR 1: assigned [mem 0x20100000-0x2010ffff]
- [ 1.969753] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x2000ffff]
- [ 1.983244] pci 0000:00:01.0: PCI bridge to [bus 01]
- [ 1.993091] pci 0000:00:01.0: bridge window [mem 0x20000000-0x200fffff]
- [ 2.006706] pci 0000:00:01.0: of_irq_parse_pci() failed with rc=-22
- [ 2.020485] clocksource: Switched to clocksource MIPS
- [ 2.032560] NET: Registered protocol family 2
- [ 2.042358] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 2.056188] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 2.068755] TCP: Hash tables configured (established 1024 bind 1024)
- [ 2.081599] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 2.093152] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 2.106060] NET: Registered protocol family 1
- [ 2.123666] rt-timer 10000100.timer: maximum frequency is 3814Hz
- [ 2.136819] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 2.149044] Crashlog allocated RAM at address 0x1f00000
- [ 2.181862] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 2.193434] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 2.216965] io scheduler noop registered
- [ 2.224712] io scheduler deadline registered (default)
- [ 2.235183] ralink-usb-phy usbphy: invalid resource
- [ 2.245777] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
- [ 2.259834] console [ttyS0] disabled
- [ 2.266943] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
- [ 2.286580] console [ttyS0] enabled
- [ 2.286580] console [ttyS0] enabled
- [ 2.300380] bootconsole [early0] disabled
- [ 2.300380] bootconsole [early0] disabled
- [ 2.317758] 1c000000.nor-flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022a8
- [ 2.338876] Amd/Fujitsu Extended Query Table at 0x0040
- [ 2.349133] Amd/Fujitsu Extended Query version 1.1.
- [ 2.359208] number of CFI chips: 1
- [ 2.370016] 6 ofpart partitions found on MTD device 1c000000.nor-flash
- [ 2.383128] Creating 6 MTD partitions on "1c000000.nor-flash":
- [ 2.394775] 0x000000000000-0x000000030000 : "uboot"
- [ 2.406972] 0x000000030000-0x000000034000 : "uboot-env"
- [ 2.420153] 0x000000034000-0x000000038000 : "factory"
- [ 2.433004] 0x000000038000-0x000000040000 : "nvram"
- [ 2.445445] 0x000000040000-0x000000050000 : "devdata"
- [ 2.458303] 0x000000050000-0x000000400000 : "firmware"
- [ 2.473602] 2 seama-fw partitions found on MTD device firmware
- [ 2.485341] 0x000000050040-0x000000190000 : "kernel"
- [ 2.497757] 0x000000190000-0x000000400000 : "rootfs"
- [ 2.510402] mtd: device 7 (rootfs) set to be root filesystem
- [ 2.521829] 1 squashfs-split partitions found on MTD device rootfs
- [ 2.534178] 0x0000003b0000-0x000000400000 : "rootfs_data"
- [ 2.550919] libphy: mdio: probed
- [ 2.559655] IP17xx: Found IP175D at mdio-bus:00
- [ 2.646731] mtk_soc_eth 10100000.ethernet: connected port 0 to PHY at mdio-bus:00 [uid=02430d80, driver=IC+ IP17xx]
- [ 2.668620] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
- [ 2.685998] rt2880_wdt 10000120.watchdog: Initialized
- [ 2.698031] NET: Registered protocol family 10
- [ 2.712715] NET: Registered protocol family 17
- [ 2.721825] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 2.747008] 8021q: 802.1Q VLAN Support v1.8
- [ 2.762700] VFS: Mounted root (squashfs filesystem) readonly on device 31:7.
- [ 2.778583] Freeing unused kernel memory: 144K (803ac000 - 803d0000)
- [ 3.679306] init: Console is alive
- [ 3.686547] init: - watchdog -
- [ 4.498655] usbcore: registered new interface driver usbfs
- [ 4.509837] usbcore: registered new interface driver hub
- [ 4.520655] usbcore: registered new device driver usb
- [ 4.540368] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 4.556060] ehci-platform: EHCI generic platform driver
- [ 4.571796] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 4.586410] ohci-platform: OHCI generic platform driver
- [ 4.608187] init: - preinit -
- [ 5.158666] 8021q: adding VLAN 0 to HW filter on device eth0
- [ 5.201497] random: procd: uninitialized urandom read (4 bytes read, 8 bits of entropy available)
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 6.810520] mtk_soc_eth 10100000.ethernet eth0: link up (100Mbps/Full duplex)
- [ 8.418769] jffs2: notice: (331) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 8.451666] mount_root: switching to jffs2 overlay
- [ 8.469995] urandom-seed: Seeding with /etc/urandom.seed
- [ 8.725147] procd: - early -
- [ 8.731185] procd: - watchdog -
- [ 8.810633] mtk_soc_eth 10100000.ethernet eth0: link down
- [ 9.346034] procd: - ubus -
- [ 9.449526] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
- [ 9.559961] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
- [ 9.578811] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
- [ 9.596846] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
- [ 9.615665] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
- [ 9.633712] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
- [ 9.652071] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
- [ 9.670604] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
- [ 9.689263] procd: - init -
- Please press Enter to activate this console.
- [ 10.136244] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 10.167133] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
- [ 10.182329] Backport generated by backports.git backports-20160324-9-g0e38f5c
- [ 10.203582] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 10.228680] nf_conntrack version 0.5.0 (444 buckets, 1776 max)
- [ 10.296745] xt_time: kernel timezone is -0000
- [ 10.405743] PPP generic driver version 2.4.2
- [ 10.418734] NET: Registered protocol family 24
- [ 10.472604] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
- [ 10.484315] rt2800pci 0000:01:00.0: loaded eeprom from mtd device "factory"
- [ 10.498279] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3071, rev 021c detected
- [ 10.513813] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
- [ 10.669497] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
- [ 10.684027] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 3883, rev 0400 detected
- [ 10.699489] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 3853 detected
- [ 12.326497] random: jshn: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
- [ 20.427387] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- [ 20.439148] 8021q: adding VLAN 0 to HW filter on device eth0
- [ 20.498979] device eth0.1 entered promiscuous mode
- [ 20.508682] device eth0 entered promiscuous mode
- [ 20.562154] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
- [ 20.647797] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
- [ 21.040687] mtk_soc_eth 10100000.ethernet eth0: link up (100Mbps/Full duplex)
- [ 21.121934] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- [ 21.220740] br-lan: port 1(eth0.1) entered forwarding state
- [ 21.232005] br-lan: port 1(eth0.1) entered forwarding state
- [ 21.243583] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
- [ 21.490750] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
- [ 23.230601] br-lan: port 1(eth0.1) entered forwarding state
- [ 24.947724] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
- [ 25.220690] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.40
- [ 25.524998] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 25.694641] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
- [ 25.707697] device wlan0 entered promiscuous mode
- [ 25.761080] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 25.774099] br-lan: port 2(wlan0) entered forwarding state
- [ 25.785195] br-lan: port 2(wlan0) entered forwarding state
- [ 25.805902] device wlan1 entered promiscuous mode
- [ 25.815526] br-lan: port 3(wlan1) entered forwarding state
- [ 25.826573] br-lan: port 3(wlan1) entered forwarding state
- [ 25.932152] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
- [ 27.780497] br-lan: port 2(wlan0) entered forwarding state
- [ 27.820553] br-lan: port 3(wlan1) entered forwarding state
- BusyBox v1.25.1 () built-in shell (ash)
- _________
- / /\ _ ___ ___ ___
- / LE / \ | | | __| \| __|
- / DE / \ | |__| _|| |) | _|
- /________/ LE \ |____|___|___/|___| lede-project.org
- \ \ DE /
- \ LE \ / -----------------------------------------------------------
- \ DE \ / Reboot (SNAPSHOT, r2669-236bf83)
- \________\/ -----------------------------------------------------------
- === WARNING! =====================================
- There is no root password defined on this device!
- Use the "passwd" command to set up a new password
- in order to prevent unauthorized SSH logins.
- --------------------------------------------------
- root@lede:/#
Add Comment
Please, Sign In to add comment