API tools faq
paste
Advertisement
buletz

Untitled

buletz
Dec 11th, 2013
202
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 13.59 KB | None | 0 0
raw download clone embed print report
  1.  
  2.  
  3. U-Boot 2009.08 (Apr 29 2012 - 07:16:04)
  4.  
  5.  
  6. CPU: Freescale i.MX53 family 2.1V at 800 MHz
  7.  
  8. mx53 pll1: 800MHz
  9.  
  10. mx53 pll2: 600MHz
  11.  
  12. mx53 pll3: 432MHz
  13.  
  14. mx53 pll4: 455MHz
  15.  
  16. ipg clock : 60000000Hz
  17.  
  18. ipg per clock : 50000000Hz
  19.  
  20. uart clock : 100000000Hz
  21.  
  22. cspi clock : 108000000Hz
  23.  
  24. ahb clock : 120000000Hz
  25.  
  26. axi_a clock : 300000000Hz
  27.  
  28. axi_b clock : 200000000Hz
  29.  
  30. emi_slow clock: 200000000Hz
  31.  
  32. ddr clock : 300000000Hz
  33.  
  34. esdhc1 clock : 120000000Hz
  35.  
  36. esdhc2 clock : 120000000Hz
  37.  
  38. esdhc3 clock : 120000000Hz
  39.  
  40. esdhc4 clock : 120000000Hz
  41.  
  42. nfc clock : 33333333Hz
  43.  
  44. Board: unknown]
  45.  
  46. Boot Device: NAND
  47.  
  48. DRAM: 256 MB
  49.  
  50. NAND: Manufacturer : Samsung (0xec)
  51.  
  52. Device Code : 0xda
  53.  
  54. Cell Technology : SLC
  55.  
  56. Chip Size : 256 MiB
  57.  
  58. Pages per Block : 64
  59.  
  60. Page Geometry : 2048+64
  61.  
  62. ECC Strength : 4 bits
  63.  
  64. ECC Size : 512 B
  65.  
  66. Data Setup Time : 20 ns
  67.  
  68. Data Hold Time : 10 ns
  69.  
  70. Address Setup Time: 20 ns
  71.  
  72. GPMI Sample Delay : 6 ns
  73.  
  74. tREA : Unknown
  75.  
  76. tRLOH : Unknown
  77.  
  78. tRHOH : Unknown
  79.  
  80. Description : K9F2G08U0A
  81.  
  82. Bad block table found at page 131008, version 0x01
  83.  
  84. Bad block table found at page 130944, version 0x01
  85.  
  86. nand_read_bbt: Bad block at 0x0000000c0000
  87.  
  88. nand_read_bbt: Bad block at 0x000005360000
  89.  
  90. nand_read_bbt: Bad block at 0x00000f180000
  91.  
  92. 256 MiB
  93.  
  94. MMC: FSL_ESDHC: 0
  95.  
  96. In: serial
  97.  
  98. Out: serial
  99.  
  100. Err: serial
  101.  
  102. Net: FEC0 [PRIME]
  103.  
  104. Hit any key to stop autoboot: 3  2  1  0
  105.  
  106.  
  107. NAND read: device 0 offset 0x1a00000, size 0x5e0000
  108.  
  109. 6160384 bytes read: OK
  110.  
  111. ## Booting kernel from Legacy Image at 70800000 ...
  112.  
  113. Image Name: linux-2.6
  114.  
  115. Image Type: ARM Linux Kernel Image (uncompressed)
  116.  
  117. Data Size: 2479372 Bytes = 2.4 MB
  118.  
  119. Load Address: 70008000
  120.  
  121. Entry Point: 70008000
  122.  
  123. Verifying Checksum ... OK
  124.  
  125. Loading Kernel Image ... OK
  126.  
  127. OK
  128.  
  129.  
  130. Starting kernel ...
  131.  
  132.  
  133. Linux version 2.6.35.3-1129-g691c08a (user@imx535-bld) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #435 PREEMPT Sun Apr 29 07:17:45 UTC 2012
  134. CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f
  135. CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
  136. Machine: Freescale MX53 LOCO Board
  137. Ignoring unrecognised tag 0x54410009
  138. Memory policy: ECC disabled, Data cache writeback
  139. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 56896
  140. Kernel command line: noinitrd console=ttymxc0,115200 ubi.mtd=1 root=ubi0:nandfs rw rootfstype=ubifs video=mxcdi0fb:RGB888,SK-800x480-LVDS video=mxcdi1fb:RGB888,SK-800x480-LVDS di0_primary ldb=di0
  141. PID hash table entries: 1024 (order: 0, 4096 bytes)
  142. Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
  143. Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
  144. Memory: 224MB = 224MB total
  145. Memory: 222312k/222312k available, 7064k reserved, 0K highmem
  146. Virtual kernel memory layout:
  147. vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  148. fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  149. DMA : 0xf9e00000 - 0xffe00000 ( 96 MB)
  150. vmalloc : 0x8e800000 - 0xf4000000 (1624 MB)
  151. lowmem : 0x80000000 - 0x8e000000 ( 224 MB)
  152. pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
  153. modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
  154. .init : 0x80008000 - 0x80028000 ( 128 kB)
  155. .text : 0x80028000 - 0x80471000 (4388 kB)
  156. .data : 0x80490000 - 0x804cce20 ( 244 kB)
  157. SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  158. Hierarchical RCU implementation.
  159. RCU-based detection of stalled CPUs is disabled.
  160. Verbose stalled-CPUs detection is disabled.
  161. NR_IRQS:368
  162. MXC GPIO hardware
  163. MXC IRQ initialized
  164. MXC_Early serial console at MMIO 0x53fbc000 (options '115200')
  165. bootconsole [ttymxc0] enabled
  166. Console: colour dummy device 80x30
  167. Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
  168. pid_max: default: 32768 minimum: 301
  169. Mount-cache hash table entries: 512
  170. CPU: Testing write buffer coherency: ok
  171. regulator: core version 0.5
  172. regulator: dummy:
  173. NET: Registered protocol family 16
  174. i.MX IRAM pool: 128 KB@0x8e840000
  175. IRAM READY
  176. CPU is i.MX53 Revision 2.1
  177. Using SDMA I.API
  178. MXC DMA API initialized
  179. IMX usb wakeup probe
  180. IMX usb wakeup probe
  181. bio: create slab <bio-0> at 0
  182. SCSI subsystem initialized
  183. usbcore: registered new interface driver usbfs
  184. usbcore: registered new interface driver hub
  185. usbcore: registered new device driver usb
  186. IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  187. Advanced Linux Sound Architecture Driver Version 1.0.23.
  188. Switching to clocksource mxc_timer1
  189. NET: Registered protocol family 2
  190. IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
  191. TCP established hash table entries: 8192 (order: 4, 65536 bytes)
  192. TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
  193. TCP: Hash tables configured (established 8192 bind 8192)
  194. TCP reno registered
  195. UDP hash table entries: 256 (order: 0, 4096 bytes)
  196. UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  197. NET: Registered protocol family 1
  198. LPMode driver module loaded
  199. Static Power Management for Freescale i.MX5
  200. PM driver module loaded
  201. sdram autogating driver module loaded
  202. Bus freq driver module loaded
  203. DI0 is primary
  204. mxc_dvfs_core_probe
  205. regulator: get() with no identifier
  206. mxc_dvfs_core_probe: failed to get gp regulator
  207. DVFS driver module loaded
  208. i.MXC CPU frequency driver
  209. regulator: get() with no identifier
  210. mxc_cpufreq_driver_init: failed to get gp regulator
  211. DVFS PER driver module loaded
  212. msgmni has been set to 434
  213. alg: No test for stdrng (krng)
  214. cryptodev: driver loaded.
  215. io scheduler noop registered
  216. io scheduler deadline registered
  217. io scheduler cfq registered (default)
  218. regulator: get() with no identifier
  219. mxc_ipu mxc_ipu: Channel already disabled 9
  220. mxc_ipu mxc_ipu: Channel already uninitialized 9
  221. Console: switching to colour frame buffer device 100x30
  222. mxc_ipu mxc_ipu: Channel already disabled 7
  223. mxc_ipu mxc_ipu: Channel already uninitialized 7
  224. mxc_ipu mxc_ipu: Channel already disabled 10
  225. mxc_ipu mxc_ipu: Channel already uninitialized 10
  226. Serial: MXC Internal UART driver
  227. mxcintuart.0: ttymxc0 at MMIO 0x53fbc000 (irq = 31) is a Freescale i.MX
  228. console [ttymxc0] enabled, bootconsole disabled
  229.  
  230. console [ttymxc0] enabled, bootconsole disabled
  231. mxcintuart.1: ttymxc1 at MMIO 0x53fc0000 (irq = 32) is a Freescale i.MX
  232.  
  233. mxcintuart.2: ttymxc2 at MMIO 0x5000c000 (irq = 33) is a Freescale i.MX
  234.  
  235. mxcintuart.3: ttymxc3 at MMIO 0x53ff0000 (irq = 13) is a Freescale i.MX
  236.  
  237. mxcintuart.4: ttymxc4 at MMIO 0x63f90000 (irq = 86) is a Freescale i.MX
  238.  
  239. loop: module loaded
  240.  
  241. NO SATA device is found, relase resource!
  242.  
  243. MXC MTD nand Driver 3.0
  244.  
  245. NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
  246.  
  247. RedBoot partition parsing not available
  248.  
  249. Creating 2 MTD partitions on "NAND 256MiB 3,3V 8-bit":
  250.  
  251. 0x000000000000-0x000002000000 : "bootloader and kernel"
  252.  
  253. 0x000002000000-0x000010000000 : "nand.rootfs"
  254.  
  255. UBI: attaching mtd1 to ubi0
  256.  
  257. UBI: physical eraseblock size: 131072 bytes (128 KiB)
  258.  
  259. UBI: logical eraseblock size: 129024 bytes
  260.  
  261. UBI: smallest flash I/O unit: 2048
  262.  
  263. UBI: sub-page size: 512
  264.  
  265. UBI: VID header offset: 512 (aligned 512)
  266.  
  267. UBI: data offset: 2048
  268.  
  269. UBI: attached mtd1 to ubi0
  270.  
  271. UBI: MTD device name: "nand.rootfs"
  272.  
  273. UBI: MTD device size: 224 MiB
  274.  
  275. UBI: number of good PEBs: 1786
  276.  
  277. UBI: number of bad PEBs: 6
  278.  
  279. UBI: max. allowed volumes: 128
  280.  
  281. UBI: wear-leveling threshold: 4096
  282.  
  283. UBI: number of internal volumes: 1
  284.  
  285. UBI: number of user volumes: 1
  286.  
  287. UBI: available PEBs: 139
  288.  
  289. UBI: total number of reserved PEBs: 1647
  290.  
  291. UBI: number of PEBs reserved for bad PEB handling: 17
  292.  
  293. UBI: max/mean erase counter: 1/0
  294.  
  295. UBI: image sequence number: 611290246
  296.  
  297. UBI: background thread "ubi_bgt0d" started, PID 473
  298.  
  299. vcan: Virtual CAN interface driver
  300.  
  301. flexcan netdevice driver
  302.  
  303. flexcan imx53-flexcan.0: device registered (reg_base=8ea10000, irq=82)
  304.  
  305. flexcan imx53-flexcan.1: device registered (reg_base=8ea18000, irq=83)
  306.  
  307. CAN device driver interface
  308.  
  309. FEC Ethernet Driver
  310.  
  311. fec_enet_mii_bus: probed
  312.  
  313. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  314.  
  315. fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
  316.  
  317. fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
  318.  
  319. fsl-ehci fsl-ehci.0: irq 18, io base 0x53f80000
  320.  
  321. fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
  322.  
  323. hub 1-0:1.0: USB hub found
  324.  
  325. hub 1-0:1.0: 1 port detected
  326.  
  327. fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
  328.  
  329. fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
  330.  
  331. fsl-ehci fsl-ehci.1: irq 14, io base 0x53f80200
  332.  
  333. fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
  334.  
  335. hub 2-0:1.0: USB hub found
  336.  
  337. hub 2-0:1.0: 1 port detected
  338.  
  339. usbcore: registered new interface driver cdc_acm
  340.  
  341. cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
  342.  
  343. Initializing USB Mass Storage driver...
  344.  
  345. usbcore: registered new interface driver usb-storage
  346.  
  347. USB Mass Storage support registered.
  348.  
  349. mice: PS/2 mouse device common for all mice
  350.  
  351. spi0.0 supply vcc not found, using dummy regulator
  352.  
  353. ads7846 spi0.0: touchscreen, irq 137
  354.  
  355. input: ADS7843 Touchscreen as /devices/platform/spi_gpio.0/spi0.0/input/input0
  356.  
  357. spi1.0 supply vcc not found, using dummy regulator
  358.  
  359. ads7846 spi1.0: touchscreen, irq 131
  360.  
  361. input: ADS7843 Touchscreen as /devices/platform/spi_gpio.1/spi1.0/input/input1
  362.  
  363. rtc-ds1307 1-0068: rtc core: registered ds1338 as rtc0
  364.  
  365. rtc-ds1307 1-0068: 56 bytes nvram
  366.  
  367. mxc_rtc mxc_rtc.0: rtc core: registered mxc_rtc as rtc1
  368.  
  369. i2c /dev entries driver
  370.  
  371. Linux video capture interface: v2.00
  372.  
  373. mxc_v4l2_output mxc_v4l2_output.0: Registered device video1
  374.  
  375. MXC WatchDog Driver 2.0
  376.  
  377. MXC Watchdog # 0 Timer: initial timeout 60 sec
  378.  
  379. VPU initialized
  380.  
  381. mxc_asrc registered
  382.  
  383. gpu mmu enabled
  384.  
  385. mxsdhci: MXC Secure Digital Host Controller Interface driver
  386.  
  387. mxsdhci: MXC SDHCI Controller Driver.
  388.  
  389. mmc0: SDHCI detect irq 135 irq 1 INTERNAL DMA
  390.  
  391. mxsdhci: MXC SDHCI Controller Driver.
  392.  
  393. mmc1: SDHCI detect irq 129 irq 2 INTERNAL DMA
  394.  
  395. usbcore: registered new interface driver usbhid
  396.  
  397. usbhid: USB HID core driver
  398.  
  399. No device for DAI tlv320aic23
  400.  
  401. No device for DAI imx-ssi-1-0
  402.  
  403. No device for DAI imx-ssi-1-1
  404.  
  405. No device for DAI imx-ssi-2-0
  406.  
  407. No device for DAI imx-ssi-2-1
  408.  
  409. AIC23 Audio Codec 0.1
  410.  
  411. DMA Sound Buffer Allocated: Playback UseIram=1 ext_ram=0 buf->addr=f8016000 buf->area=8e856000 size=24576
  412.  
  413. DMA Sound Buffer Allocated: Capture UseIram=1 ext_ram=1 buf->addr=7d268000 buf->area=fa8ac000 size=24576
  414.  
  415. asoc: tlv320aic23 <-> imx-ssi-2-0 mapping ok
  416.  
  417. ALSA device list:
  418.  
  419. #0: imx-3stack (tlv320aic23)
  420.  
  421. TCP cubic registered
  422.  
  423. NET: Registered protocol family 17
  424.  
  425. can: controller area network core (rev 20090105 abi 8)
  426.  
  427. NET: Registered protocol family 29
  428.  
  429. can: raw protocol (rev 20090105)
  430.  
  431. can: broadcast manager protocol (rev 20090105 t)
  432.  
  433. VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
  434.  
  435. rtc-ds1307 1-0068: setting system clock to 2033-01-12 19:23:25 UTC (1989170605)
  436.  
  437. UBIFS: recovery needed
  438.  
  439. UBIFS: recovery completed
  440.  
  441. UBIFS: mounted UBI device 0, volume 0, name "nandfs"
  442.  
  443. UBIFS: file system size: 208373760 bytes (203490 KiB, 198 MiB, 1615 LEBs)
  444.  
  445. UBIFS: journal size: 10450944 bytes (10206 KiB, 9 MiB, 81 LEBs)
  446.  
  447. UBIFS: media format: w4/r0 (latest is w4/r0)
  448.  
  449. UBIFS: default compressor: lzo
  450.  
  451. UBIFS: reserved for root: 4952683 bytes (4836 KiB)
  452.  
  453. VFS: Mounted root (ubifs filesystem) on device 0:10.
  454.  
  455. Freeing init memory: 128K
  456.  
  457. mmc0: new high speed SDHC card at address aaaa
  458.  
  459. mmcblk0: mmc0:aaaa SU16G 14.8 GiB
  460.  
  461. mmcblk0: p1
  462.  
  463. UBIFS error (pid 1): ubifs_check_node: bad CRC: calculated 0x5dd01459, read 0x823ee1d4
  464.  
  465. UBIFS error (pid 1): ubifs_check_node: bad node at LEB 893:67400
  466.  
  467. UBIFS error (pid 1): ubifs_read_node: expected node type 9
  468.  
  469. UBIFS error (pid 1): ubifs_iget: failed to read inode 6894, error -117
  470.  
  471. UBIFS error (pid 1): ubifs_lookup: dead directory entry 'etc', error -117
  472.  
  473. UBIFS warning (pid 1): ubifs_ro_mode: switched to read-only mode, error -117
  474.  
  475. UBIFS error (pid 1): ubifs_check_node: bad CRC: calculated 0x5dd01459, read 0x823ee1d4
  476.  
  477. UBIFS error (pid 1): ubifs_check_node: bad node at LEB 893:67400
  478.  
  479. UBIFS error (pid 1): ubifs_read_node: expected node type 9
  480.  
  481. UBIFS error (pid 1): ubifs_iget: failed to read inode 6894, error -117
  482.  
  483. UBIFS error (pid 1): ubifs_lookup: dead directory entry 'etc', error -117
  484.  
  485. UBIFS error (pid 1): ubifs_check_node: bad CRC: calculated 0x5dd01459, read 0x823ee1d4
  486.  
  487. UBIFS error (pid 1): ubifs_check_node: bad node at LEB 893:67400
  488.  
  489. UBIFS error (pid 1): ubifs_read_node: expected node type 9
  490.  
  491. UBIFS error (pid 1): ubifs_iget: failed to read inode 6894, error -117
  492.  
  493. UBIFS error (pid 1): ubifs_lookup: dead directory entry 'etc', error -117
  494.  
  495. UBIFS error (pid 611): ubifs_check_node: bad CRC: calculated 0x5dd01459, read 0x823ee1d4
  496.  
  497. UBIFS error (pid 611): ubifs_check_node: bad node at LEB 893:67400
  498.  
  499. UBIFS error (pid 611): ubifs_read_node: expected node type 9
  500.  
  501. UBIFS error (pid 611): ubifs_iget: failed to read inode 6894, error -117
  502.  
  503. UBIFS error (pid 611): ubifs_lookup: dead directory entry 'etc', error -117
  504.  
  505. UBIFS error (pid 611): ubifs_check_node: bad CRC: calculated 0x5dd01459, read 0x823ee1d4
  506.  
  507. UBIFS error (pid 611): ubifs_check_node: bad node at LEB 893:67400
  508.  
  509. UBIFS error (pid 611): ubifs_read_node: expected node type 9
  510.  
  511. UBIFS error (pid 611): ubifs_iget: failed to read inode 6894, error -117
  512.  
  513. UBIFS error (pid 611): ubifs_lookup: dead directory entry 'etc', error -117
  514.  
  515.  
  516. can't run '/etc/init.d/rcS': Structure needs cleaning
  517.  
  518. Please press Enter to activate this console.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!