Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- Starting kernel ...
- Uncompressing Linux.............................................................
- Linux version 2.6.32 (a0393957@swubn01) (gcc version 4.4.3 (GCC) ) #1 Thu Mar 31
- CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
- CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
- Machine: OMAP3 Beagle Board
- Memory policy: ECC disabled, Data cache writeback
- OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp 720m )
- SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
- Reserving 4194304 bytes SDRAM for VRAM
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
- Kernel command line: console=ttyS2,115200n8 androidboot.console=ttyS2 mem=256M y
- PID hash table entries: 1024 (order: 0, 4096 bytes)
- Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
- Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
- Memory: 256MB = 256MB total
- Memory: 249856KB available (4532K code, 825K data, 172K init, 0K highmem)
- Hierarchical RCU implementation.
- NR_IRQS:402
- Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
- Reprogramming SDRC clock to 332000000 Hz
- GPMC revision 5.0
- IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
- Total of 96 interrupts on 1 active controller
- OMAP GPIO hardware version 2.5
- OMAP clockevent source: GPTIMER12 at 32768 Hz
- Console: colour dummy device 80x30
- Calibrating delay loop... 487.36 BogoMIPS (lpj=1904640)
- Mount-cache hash table entries: 512
- CPU: Testing write buffer coherency: ok
- regulator: core version 0.5
- NET: Registered protocol family 16
- Found NAND on CS0
- Registering NAND on CS0
- Unable to get DVI reset GPIO
- Target VDD1 OPP = 6, VDD2 OPP = 3
- OMAP DMA hardware revision 4.0
- bio: create slab <bio-0> at 0
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
- twl4030: PIH (irq 7) chaining IRQs 368..375
- twl4030: power (irq 373) chaining IRQs 376..383
- twl4030: gpio (irq 368) chaining IRQs 384..401
- regulator: VUSB1V5: 1500 mV normal standby
- regulator: VUSB1V8: 1800 mV normal standby
- regulator: VUSB3V1: 3100 mV normal standby
- twl4030_usb twl4030_usb: Initialized TWL4030 USB module
- regulator: VMMC1: 1850 <--> 3150 mV normal standby
- regulator: VDAC: 1800 mV normal standby
- regulator: VPLL2: 1800 mV normal standby
- regulator: VSIM: 1800 <--> 3000 mV normal standby
- regulator: VAUX3: 1800 mV normal standby
- regulator: VAUX4: 1800 mV normal standby
- i2c_omap i2c_omap.2: bus 2 rev3.12 at 100 kHz
- i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
- Switching to clocksource 32k_counter
- musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
- musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
- NET: Registered protocol family 2
- IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
- TCP established hash table entries: 8192 (order: 4, 65536 bytes)
- TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
- TCP: Hash tables configured (established 8192 bind 8192)
- TCP reno registered
- UDP hash table entries: 256 (order: 0, 4096 bytes)
- UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- NET: Registered protocol family 1
- RPC: Registered udp transport module.
- RPC: Registered tcp transport module.
- RPC: Registered tcp NFSv4.1 backchannel transport module.
- omap-iommu omap-iommu.0: isp registered
- NetWinder Floating Point Emulator V0.97 (double precision)
- ashmem: initialized
- VFS: Disk quotas dquot_6.5.2
- Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
- yaffs Mar 31 2011 09:59:47 Installing.
- msgmni has been set to 488
- alg: No test for stdrng (krng)
- io scheduler noop registered
- io scheduler deadline registered
- io scheduler cfq registered (default)
- OMAP DSS rev 2.0
- OMAP DISPC rev 3.0
- OMAP VENC rev 2
- Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
- serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
- serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
- console [ttyS2] enabled
- brd: module loaded
- loop: module loaded
- usbcore: registered new interface driver asix
- usbcore: registered new interface driver cdc_ether
- usbcore: registered new interface driver cdc_eem
- usbcore: registered new interface driver dm9601
- usbcore: registered new interface driver smsc95xx
- usbcore: registered new interface driver gl620a
- usbcore: registered new interface driver net1080
- usbcore: registered new interface driver plusb
- usbcore: registered new interface driver rndis_host
- usbcore: registered new interface driver cdc_subset
- usbcore: registered new interface driver zaurus
- usbcore: registered new interface driver MOSCHIP usb-ethernet driver
- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
- ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
- ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
- ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 3 ports detected
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- android init
- android_probe pdata: c04c953c
- android_bind
- android_usb gadget: android_usb ready
- musb_hdrc musb_hdrc: MUSB HDRC host driver
- musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 1 port detected
- f_adb init
- android_register_function adb
- adb_bind_config
- f_mass_storage init
- android_register_function usb_mass_storage
- mice: PS/2 mouse device common for all mice
- input: gpio-keys as /devices/platform/gpio-keys/input/input0
- i2c /dev entries driver
- Linux video capture interface: v2.00
- omap-iommu omap-iommu.0: isp: version 1.1
- OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
- mmci-omap-hs mmci-omap-hs.1: err -16 configuring card detect
- usbcore: registered new interface driver usbhid
- usbhid: USB HID core driver
- logger: created 64K log 'log_main'
- logger: created 256K log 'log_events'
- logger: created 64K log 'log_radio'
- logger: created 64K log 'log_system'
- Advanced Linux Sound Architecture Driver Version 1.0.21.
- usbcore: registered new interface driver snd-usb-audio
- usb 1-2: new high speed USB device using ehci-omap and address 2
- No device for DAI omap-mcbsp-dai-0
- No device for DAI omap-mcbsp-dai-1
- No device for DAI omap-mcbsp-dai-2
- No device for DAI omap-mcbsp-dai-3
- No device for DAI omap-mcbsp-dai-4
- OMAP3 Beagle SoC init
- asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
- ALSA device list:
- #0: omap3beagle (twl4030)
- TCP cubic registered
- NET: Registered protocol family 17
- NET: Registered protocol family 15
- Power Management for TI OMAP3.
- ------------[ cut here ]------------
- WARNING: at arch/arm/mach-omap2/dpll.c:439 omap3_noncore_dpll_set_rate+0x220/0x)
- Modules linked in:
- [<c00399b0>] (unwind_backtrace+0x0/0xd8) from [<c005f8dc>] (warn_slowpath_commo)
- [<c005f8dc>] (warn_slowpath_common+0x48/0x60) from [<c0043884>] (omap3_noncore_)
- [<c0043884>] (omap3_noncore_dpll_set_rate+0x220/0x264) from [<c0041e9c>] (omap2)
- [<c0041e9c>] (omap2_clk_set_rate+0x20/0x2c) from [<c00487d0>] (clk_set_rate+0x3)
- [<c00487d0>] (clk_set_rate+0x38/0x88) from [<c0010418>] (omap2_clk_set_freq+0x2)
- unwind: Unknown symbol address c0010418
- unwind: Index not found c0010418
- ---[ end trace 3b6e45b9b3f26cf4 ]---
- Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/720 MHz
- IVA2 clocking rate: 520 MHz
- SmartReflex driver initialized
- VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
- omapdss DPI: Could not find exact pixel clock. Requested 23500 kHz, got 24000 kz
- regulator_init_complete: incomplete constraints, leaving VAUX3 on
- regulator_init_complete: incomplete constraints, leaving VDVI on
- regulator_init_complete: incomplete constraints, leaving VDAC on
- drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
- omapdss DPI error: display already enabled
- omap_vout omap_vout: 'dvi' Display already enabled
- omapdss DPI error: display already enabled
- omap_vout omap_vout: 'dvi' Display already enabled
- omap_vout omap_vout: Buffer Size = 3686400
- omap_vout omap_vout: : registered and initialized video device 0
- omap_vout omap_vout: Buffer Size = 3686400
- omap_vout omap_vout: : registered and initialized video device 1
- Waiting 1sec before mounting root device...
- hub 1-2:1.0: USB hub found
- hub 1-2:1.0: 4 ports detected
- mmc0: new SDHC card at address e624
- mmcblk0: mmc0:e624 SD04G 3.69 GiB
- mmcblk0: p1 p2 p3
- usb 1-2.1: new high speed USB device using ehci-omap and address 3
- eth0: register 'asix' at usb-ehci-omap.0-2.1, ASIX AX88772 USB 2.0 Ethernet, 001
- kjournald starting. Commit interval 5 seconds
- EXT3-fs (mmcblk0p2): using internal journal
- EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
- VFS: Mounted root (ext3 filesystem) on device 179:2.
- Freeing init memory: 172K
- Warning: unable to open an initial console.
- usb 1-2.3: new low speed USB device using ehci-omap and address 4
- input: CHICONY HP Basic USB Keyboard as /devices/platform/ehci-omap.0/usb1/1-2/1
- generic-usb 0003:03F0:0024.0001: input: USB HID v1.10 Keyboard [CHICONY HP Basi0
- init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
- usb 1-2.4: new low speed USB device using ehci-omap and address 5
- input: Microsoft Basic Optical Mouse as /devices/platform/ehci-omap.0/usb1/1-2/2
- generic-usb 0003:045E:0083.0002: input: USB HID v1.10 Mouse [Microsoft Basic Op0
- # enabling adb
- adb_open
- warning: `zygote' uses 32-bit capabilities (legacy support in use)
- alarm_set_rtc: no RTC, time will be lost on reboot
- request_suspend_state: wakeup (3->0) at 17229309085 (1970-01-02 00:00:05.645996)
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement