Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot SPL 2012.07 (Aug 10 2012 - 09:11:31)
- Texas Instruments Revision detection unimplemented
- OMAP SD/MMC: 0
- reading u-boot.img
- reading u-boot.img
- U-Boot 2012.07 (Aug 10 2012 - 09:11:31)
- OMAP3630/3730-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
- OMAP3 Beagle board + LPDDR/NAND
- I2C: ready
- DRAM: 512 MiB
- NAND: 0 MiB
- MMC: OMAP SD/MMC: 0
- *** Warning - readenv() failed, using default environment
- In: serial
- Out: serial
- Err: serial
- Beagle xM Rev C
- No EEPROM on expansion board
- No EEPROM on expansion board
- Die ID #1d2a00029ff800000163810c13006013
- Net: Net Initialization Skipped
- No ethernet found.
- Hit any key to stop autoboot: 3 2 1 0
- gpio: pin 173 (gpio 173) value is 0
- gpio: pin 4 (gpio 4) value is 0
- SD/MMC found on device 0
- reading uEnv.txt
- 909 bytes read
- Loaded environment from uEnv.txt
- Importing environment from mmc ...
- reading zImage
- 3016088 bytes read
- Booting from mmc ...
- Starting kernel ...
- Uncompressing Linux... done, booting the kernel.
- [ 0.000000] Booting Linux on physical CPU 0
- [ 0.000000] Initializing cgroup subsys cpuset
- [ 0.000000] Initializing cgroup subsys cpu
- [ 0.000000] Linux version 3.2.26-x14 (voodoo@work-e6400) (gcc version 4.6.4 20120508 (prerelease) (Linaro GCC 4.6-2012.05) ) #1 SMP Fri Aug 10 10:07:28 CDT 2012
- [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000] Machine: OMAP3 Beagle Board
- [ 0.000000] Beagle expansionboard: none
- [ 0.000000] Beagle second expansionboard: none
- [ 0.000000] Reserving 12582912 bytes SDRAM for VRAM
- [ 0.000000] Memory policy: ECC disabled, Data cache writeback
- [ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
- [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz
- [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0d0c000 s10816 r8192 d13760 u32768
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125440
- [ 0.000000] Kernel command line: console=ttyO2,115200n8 console=tty0 vram=12M omapfb.mode=dvi:1280x720MR-16@60 omapdss.def_disp=dvi root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait fixrtc buddy=none buddy2=none
- [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000] allocated 2097152 bytes of page_cgroup
- [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
- [ 0.000000] Memory: 494MB = 494MB total
- [ 0.000000] Memory: 490020k/490020k available, 34268k reserved, 0K highmem
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- [ 0.000000] vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB)
- [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
- [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- [ 0.000000] .text : 0xc0008000 - 0xc078237c (7657 kB)
- [ 0.000000] .init : 0xc0783000 - 0xc07d8a40 ( 343 kB)
- [ 0.000000] .data : 0xc07da000 - 0xc0843dd0 ( 424 kB)
- [ 0.000000] .bss : 0xc0843df4 - 0xc0907df0 ( 784 kB)
- [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:410 nr_irqs:410 410
- [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
- [ 0.000000] Total of 96 interrupts on 1 active controller
- [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
- [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
- [ 0.000000] Console: colour dummy device 80x30
- [ 0.000000] console [tty0] enabled
- [ 0.000671] Calibrating delay loop... 500.97 BogoMIPS (lpj=1953792)
- [ 0.039337] pid_max: default: 32768 minimum: 301
- [ 0.039611] Security Framework initialized
- [ 0.039703] AppArmor: AppArmor initialized
- [ 0.039978] Mount-cache hash table entries: 512
- [ 0.040954] Initializing cgroup subsys cpuacct
- [ 0.041046] Initializing cgroup subsys memory
- [ 0.041107] Initializing cgroup subsys devices
- [ 0.041137] Initializing cgroup subsys freezer
- [ 0.041168] Initializing cgroup subsys blkio
- [ 0.041198] Initializing cgroup subsys perf_event
- [ 0.041320] CPU: Testing write buffer coherency: ok
- [ 0.041595] CPU0: thread -1, cpu 0, socket -1, mpidr 0
- [ 0.042297] Brought up 1 CPUs
- [ 0.042327] SMP: Total of 1 processors activated (500.97 BogoMIPS).
- [ 0.043395] devtmpfs: initialized
- [ 0.049499] print_constraints: dummy:
- [ 0.049896] NET: Registered protocol family 16
- [ 0.050079] GPMC revision 5.0
- [ 0.051666] OMAP GPIO hardware version 2.5
- [ 0.053497] omap_mux_init: Add partition: #1: core, flags: 0
- [ 0.054748] OMAP3 Beagle Rev: xM C
- [ 0.058258] Reprogramming SDRC clock to 400000000 Hz
- [ 0.058319] dpll3_m2_clk rate change failed: -22
- [ 0.060089] Found NAND on CS0
- [ 0.060119] Registering NAND on CS0
- [ 0.060455] Unable to get DVI reset GPIO
- [ 0.060607] hw-breakpoint: debug architecture 0x4 unsupported.
- [ 0.061279] Could not look up mcpdm hw_mod
- [ 0.064544] omap-mcbsp.2: alias fck already exists
- [ 0.064758] omap-mcbsp.3: alias fck already exists
- [ 0.066162] OMAP DMA hardware revision 5.0
- [ 0.074249] bio: create slab <bio-0> at 0
- [ 0.075744] SCSI subsystem initialized
- [ 0.077117] usbcore: registered new interface driver usbfs
- [ 0.077270] usbcore: registered new interface driver hub
- [ 0.077514] usbcore: registered new device driver usb
- [ 0.078430] omap_i2c omap_i2c.1: bus 1 rev1.4.0 at 2600 kHz
- [ 0.081207] twl4030: PIH (irq 7) chaining IRQs 368..375
- [ 0.081359] twl4030: power (irq 373) chaining IRQs 376..383
- [ 0.081970] twl4030: gpio (irq 368) chaining IRQs 384..401
- [ 0.082366] _omap_mux_init_gpio: Could not set gpio192
- [ 0.084594] print_constraints: VUSB1V5: 1500 mV normal standby
- [ 0.085113] print_constraints: VUSB1V8: 1800 mV normal standby
- [ 0.085571] print_constraints: VUSB3V1: 3100 mV normal standby
- [ 0.087554] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
- [ 0.088439] print_constraints: VMMC1: 1850 <--> 3150 mV at 3150 mV normal standby
- [ 0.088958] print_constraints: VDAC: 1800 mV normal standby
- [ 0.089416] print_constraints: VAUX2_4030: 1800 mV normal
- [ 0.089874] print_constraints: VDVI: 1800 mV normal standby
- [ 0.090423] print_constraints: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby
- [ 0.090850] omap_i2c omap_i2c.2: bus 2 rev1.4.0 at 400 kHz
- [ 0.091125] omap_i2c omap_i2c.3: bus 3 rev1.4.0 at 100 kHz
- [ 0.092559] NetLabel: Initializing
- [ 0.092590] NetLabel: domain hash size = 128
- [ 0.092620] NetLabel: protocols = UNLABELED CIPSOv4
- [ 0.092681] NetLabel: unlabeled traffic allowed by default
- [ 0.092742] Switching to clocksource 32k_counter
- [ 0.112060] AppArmor: AppArmor Filesystem Enabled
- [ 0.126403] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
- [ 0.131683] musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
- [ 0.132202] NET: Registered protocol family 2
- [ 0.132629] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.133728] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
- [ 0.134124] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
- [ 0.134490] TCP: Hash tables configured (established 16384 bind 16384)
- [ 0.134521] TCP reno registered
- [ 0.134521] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.134582] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.134979] NET: Registered protocol family 1
- [ 0.135559] RPC: Registered named UNIX socket transport module.
- [ 0.135589] RPC: Registered udp transport module.
- [ 0.135620] RPC: Registered tcp transport module.
- [ 0.135620] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 0.136047] omap_dsp_init: 600000 bytes @ 9ee00000
- [ 0.137908] audit: initializing netlink socket (disabled)
- [ 0.137969] type=2000 audit(0.148:1): initialized
- [ 0.342559] VFS: Disk quotas dquot_6.5.2
- [ 0.343200] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 0.347778] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
- [ 0.347869] fuse init (API version 7.17)
- [ 0.350036] Btrfs loaded
- [ 0.350097] msgmni has been set to 957
- [ 0.351867] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
- [ 0.351928] io scheduler noop registered
- [ 0.351928] io scheduler deadline registered
- [ 0.352020] io scheduler cfq registered (default)
- [ 0.353057] OMAP DSS rev 2.0
- [ 0.356170] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- [ 0.357635] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
- [ 0.358001] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
- [ 0.358367] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
- [ 1.116394] console [ttyO2] enabled
- [ 1.120422] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP UART3
- [ 1.138977] brd: module loaded
- [ 1.147186] loop: module loaded
- [ 1.151580] twl4030_madc twl4030_madc: clk disabled, enabling
- [ 1.159545] omap2-nand driver initializing
- [ 1.164245] No NAND device found
- [ 1.167846] No NAND device found
- [ 1.171478] OneNAND driver initializing
- [ 1.176269] usbcore: registered new interface driver cdc_ether
- [ 1.182464] usbcore: registered new interface driver rndis_host
- [ 1.188720] cdc_ncm: 04-Aug-2011
- [ 1.192138] usbcore: registered new interface driver cdc_ncm
- [ 1.198608] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 3.217895] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
- [ 3.224273] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
- [ 3.232147] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
- [ 3.249206] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
- [ 3.255340] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- [ 3.262451] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 3.270019] usb usb1: Product: OMAP-EHCI Host Controller
- [ 3.275604] usb usb1: Manufacturer: Linux 3.2.26-x14 ehci_hcd
- [ 3.281616] usb usb1: SerialNumber: ehci-omap.0
- [ 3.287078] hub 1-0:1.0: USB hub found
- [ 3.291076] hub 1-0:1.0: 3 ports detected
- [ 3.319488] Initializing USB Mass Storage driver...
- [ 3.324737] usbcore: registered new interface driver usb-storage
- [ 3.331054] USB Mass Storage support registered.
- [ 3.336029] usbcore: registered new interface driver libusual
- [ 3.342254] udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
- [ 3.349212] gadget: using random self ethernet address
- [ 3.354736] gadget: using random host ethernet address
- [ 3.361450] usb0: MAC f6:bb:97:97:79:22
- [ 3.365478] usb0: HOST MAC ba:9c:9a:8f:0c:75
- [ 3.370025] gadget: Ethernet Gadget, version: Memorial Day 2008
- [ 3.376342] gadget: g_ether ready
- [ 3.379913] musb-hdrc musb-hdrc: MUSB HDRC host driver
- [ 3.385650] musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 2
- [ 3.393371] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
- [ 3.400482] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 3.408050] usb usb2: Product: MUSB HDRC host driver
- [ 3.413269] usb usb2: Manufacturer: Linux 3.2.26-x14 musb-hcd
- [ 3.419281] usb usb2: SerialNumber: musb-hdrc
- [ 3.424530] hub 2-0:1.0: USB hub found
- [ 3.428497] hub 2-0:1.0: 1 port detected
- [ 3.433563] mousedev: PS/2 mouse device common for all mice
- [ 3.440673] input: twl4030_pwrbutton as /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input0
- [ 3.452697] i2c /dev entries driver
- [ 3.457031] Linux media interface: v0.10
- [ 3.461334] lirc_dev: IR Remote Control driver registered, major 249
- [ 3.468078] Driver for 1-wire Dallas network protocol.
- [ 3.474304] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
- [ 3.481079] twl4030_wdt twl4030_wdt: Failed to register misc device
- [ 3.487670] twl4030_wdt: probe of twl4030_wdt failed with error -16
- [ 3.495391] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
- [ 3.504791] cpuidle: using governor ladder
- [ 3.509124] cpuidle: using governor menu
- [ 3.513244] sdhci: Secure Digital Host Controller Interface driver
- [ 3.519683] sdhci: Copyright(c) Pierre Ossman
- [ 3.663391] usb 1-2: new high-speed USB device number 2 using ehci-omap
- [ 3.746795] usbcore: registered new interface driver usbhid
- [ 3.752655] usbhid: USB HID core driver
- [ 3.756652] oprofile: hardware counters not available
- [ 3.761932] oprofile: using timer interrupt.
- [ 3.767547] TCP cubic registered
- [ 3.771850] NET: Registered protocol family 10
- [ 3.779449] NET: Registered protocol family 17
- [ 3.784332] Registering the dns_resolver key type
- [ 3.789337] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
- [ 3.797363] ThumbEE CPU extension supported.
- [ 3.801818] Registering SWP/SWPB emulation handler
- [ 3.811248] sr_init: No PMIC hook to init smartreflex
- [ 3.816802] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
- [ 3.825073] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
- [ 3.833282] SmartReflex Class3 initialized
- [ 3.843078] clock: disabling unused clocks to save power
- [ 3.849639] registered taskstats version 1
- [ 3.854187] fbcvt: 1280x720@60: CVT Name - .921M9-R
- [ 3.867340] usb 1-2: New USB device found, idVendor=0424, idProduct=9514
- [ 3.874359] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
- [ 3.891357] Console: switching to colour frame buffer device 160x45
- [ 3.905944] hub 1-2:1.0: USB hub found
- [ 3.910125] hub 1-2:1.0: 5 ports detected
- [ 3.918151] regulator_init_complete: VDAC: incomplete constraints, leaving on
- [ 3.927337] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
- [ 3.934631] Waiting for root device /dev/mmcblk0p2...
- [ 4.099792] mmc0: host does not support reading read-only switch. assuming write-enable.
- [ 4.108489] mmc0: new SDHC card at address e624
- [ 4.113800] mmcblk0: mmc0:e624 SU04G 3.69 GiB
- [ 4.127471] mmcblk0: p1 p2
- [ 4.175933] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
- [ 4.187408] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
- [ 4.210632] usb 1-2.1: new high-speed USB device number 3 using ehci-omap
- [ 4.222412] devtmpfs: mounted
- [ 4.229003] Freeing init memory: 340K
- [ 4.335845] usb 1-2.1: New USB device found, idVendor=0424, idProduct=ec00
- [ 4.346099] usb 1-2.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
- [ 4.444915] usb 1-2.3: new low-speed USB device number 4 using ehci-omap
- [ 4.575866] usb 1-2.3: New USB device found, idVendor=413c, idProduct=2003
- [ 4.586120] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
- [ 4.596740] usb 1-2.3: Product: Dell USB Keyboard
- [ 4.604583] usb 1-2.3: Manufacturer: Dell
- [ 4.621948] input: Dell Dell USB Keyboard as /devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.3/1-2.3:1.0/input/input1
- [ 4.637634] generic-usb 0003:413C:2003.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-ehci-omap.0-2.3/input0
- [ 5.412994] udevd[124]: starting version 175
- [ 5.987884] input: gpio-keys as /devices/platform/gpio-keys/input/input2
- [ 6.391693] twl_rtc twl_rtc: Power up reset detected.
- [ 6.404479] twl_rtc twl_rtc: Enabling TWL-RTC.
- [ 6.458679] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
- [ 6.563995] OMAP3 Beagle/Devkit8000 SoC init
- [ 6.665222] asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok
- [ 7.072540] smsc95xx v1.0.4
- [ 7.208892] smsc95xx 1-2.1:1.0: eth0: register 'smsc95xx' at usb-ehci-omap.0-2.1, smsc95xx USB 2.0 Ethernet, 6a:5a:74:c5:06:df
- [ 7.224700] usbcore: registered new interface driver smsc95xx
- [ 7.921844] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
- [ 8.167510] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
- Debian GNU/Linux wheezy/sid devel ttyO2
- devel login: debian
- Password:
- Linux devel 3.2.26-x14 #1 SMP Fri Aug 10 10:07:28 CDT 2012 armv7l
- The programs included with the Debian GNU/Linux system are free software;
- the exact distribution terms for each program are described in the
- individual files in /usr/share/doc/*/copyright.
- Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
- permitted by applicable law.
- debian@devel:~$ uname -a
- Linux devel 3.2.26-x14 #1 SMP Fri Aug 10 10:07:28 CDT 2012 armv7l GNU/Linux
- debian@devel:~$ ls /lib/modlules/`uname -r`/
- build modules.builtin modules.devname modules.symbols.bin
- kernel modules.builtin.bin modules.order source
- modules.alias modules.dep modules.softdep
- modules.alias.bin modules.dep.bin modules.symbols
- debian@devel:~$ ls -lh /lib/modules/`uname -r`/build
- lrwxrwxrwx 1 debian fuse 37 Aug 10 2012 /lib/modules/3.2.26-x14/build -> /opt/eewiki/omap/stable-kernel/KERNEL
- debian@devel:~$ lsmod
- Module Size Used by
- smsc95xx 11302 0
- snd_soc_omap3beagle 2195 0
- rtc_twl 4418 0
- snd_soc_twl4030 37284 1
- snd_soc_omap 3353 1
- snd_soc_omap_mcbsp 8230 1
- snd_soc_core 105726 4 snd_soc_omap_mcbsp,snd_soc_omap,snd_soc_twl4030,snd_soc_omap3beagle
- regmap_spi 1231 1 snd_soc_core
- snd_pcm 80381 4 snd_soc_core,snd_soc_omap_mcbsp,snd_soc_omap,snd_soc_twl4030
- snd_page_alloc 4959 1 snd_pcm
- snd_timer 19979 1 snd_pcm
- snd 58205 3 snd_timer,snd_pcm,snd_soc_core
- soundcore 7465 1 snd
- gpio_keys 6945 0
- debian@devel:~$
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement