Beagleboard

Texas Instruments X-Loader 1.5.0 (Jun 14 2011 - 22:04:07)
Beagle xM
Reading boot sector
Loading u-boot.bin from mmc


U-Boot 2011.03-rc1-00000-g9a3cc57-dirty (Apr 01 2011 - 17:41:42)

OMAP3630/3730-GP ES2.1, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
OMAP3 Beagle board + LPDDR/NAND
I2C:   ready
DRAM:  512 MiB
NAND:  0 MiB
MMC:   OMAP SD/MMC: 0
*** Warning - readenv() failed, using default environment

In:    serial
Out:   serial
Err:   serial
Beagle xM Rev C
No EEPROM on expansion board
Die ID #54ee00029ff80000016830c40500c007
Hit any key to stop autoboot:  0
The user button is currently NOT pressed.
SD/MMC found on device 0
reading uEnv.txt

149 bytes read
Loaded environment from uEnv.txt
Importing environment from mmc ...
Loading file "/boot/uImage" from mmc device 0:2 (xxa2)
3203088 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 80200000 ...
   Image Name:   Angstrom/2.6.32/beagleboard
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3203024 Bytes = 3.1 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux....................................................................................................................................
[    0.000000] Linux version 2.6.32 (koen@dominion) (gcc version 4.3.3 (GCC) ) #3 PREEMPT Tue Jul 26 10:56:56 CEST 2011
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: OMAP3 Beagle Board
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] OMAP3630/DM3730 ES1.0 (l2cache iva sgx neon isp 192mhz_clk )
[    0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
[    0.000000] Reserving 16777216 bytes SDRAM for VRAM
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=tty0 console=ttyS2,115200n8 consoleblank=0 mpurate=auto buddy=none camera=lbcm5m03 vram=16M omapfb.mode=dvt
[    0.000000] Beagle expansionboard: none
[    0.000000] Beagle cameraboard: lbcm5m03
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 256MB 256MB = 512MB total
[    0.000000] Memory: 496256KB available (5900K code, 673K data, 204K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:402
[    0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
[    0.000000] Reprogramming SDRC clock to 332000000 Hz
[    0.000000] GPMC revision 5.0
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[    0.000000] Total of 96 interrupts on 1 active controller
[    0.000000] OMAP GPIO hardware version 2.5
[    0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [tty0] enabled
[    0.000000] Calibrating delay loop... 490.52 BogoMIPS (lpj=1916928)
[    0.000000] Mount-cache hash table entries: 512
[    0.000000] CPU: Testing write buffer coherency: ok
[    0.000000] tmpfs: No value for mount option 'mode'
[    0.000000] devtmpfs: initialized
[    0.000000] regulator: core version 0.5
[    0.000000] NET: Registered protocol family 16
[    0.000000] OMAP3 Beagle Rev: xM C
[    0.000000] Beagle cameraboard: registering i2c2 bus for lbcm5m03
[    0.000000] Found NAND on CS0
[    0.000000] Registering NAND on CS0
[    0.000000] Unable to get DVI reset GPIO
[    0.000000] omap_init_mbox: platform not supported
[  538.528778] OMAP DMA hardware revision 5.0
[  538.535125] bio: create slab <bio-0> at 0
[  538.536407] SCSI subsystem initialized
[  538.537811] usbcore: registered new interface driver usbfs
[  538.537963] usbcore: registered new interface driver hub
[  538.538146] usbcore: registered new device driver usb
[  538.538543] i2c_omap i2c_omap.1: bus 1 rev4.0 at 2600 kHz
[  538.541198] twl4030: PIH (irq 7) chaining IRQs 368..375
[  538.541259] twl4030: power (irq 373) chaining IRQs 376..383
[  538.541564] twl4030: gpio (irq 368) chaining IRQs 384..401
[  538.543273] regulator: VUSB1V5: 1500 mV normal standby
[  538.543579] regulator: VUSB1V8: 1800 mV normal standby
[  538.543823] regulator: VUSB3V1: 3100 mV normal standby
[  538.545074] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[  538.545501] regulator: VMMC1: 1850 <--> 3150 mV normal standby
[  538.545776] regulator: VDAC: 1800 mV normal standby
[  538.546020] regulator: VPLL2: 1800 mV normal standby
[  538.546295] regulator: VSIM: 1800 <--> 3000 mV normal standby
[  538.546630] regulator: VAUX3: 1800 mV normal standby
[  538.546997] regulator: VAUX4: 1800 mV normal standby
[  538.547180] i2c_omap i2c_omap.2: bus 2 rev4.0 at 400 kHz
[  538.556213] i2c_omap i2c_omap.3: bus 3 rev4.0 at 100 kHz
[  538.557403] Switching to clocksource 32k_counter
[  538.566528] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
[  538.570190] musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
[  538.570251] musb_hdrc musb_hdrc: MUSB HDRC host driver
[  538.570373] musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
[  538.570526] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[  538.570587] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[  538.570617] usb usb1: Product: MUSB HDRC host driver
[  538.570648] usb usb1: Manufacturer: Linux 2.6.32 musb-hcd
[  538.570678] usb usb1: SerialNumber: musb_hdrc
[  538.571319] hub 1-0:1.0: USB hub found
[  538.571380] hub 1-0:1.0: 1 port detected
[  538.572418] NET: Registered protocol family 2
[  538.572692] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[  538.573333] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[  538.573760] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[  538.573974] TCP: Hash tables configured (established 16384 bind 16384)
[  538.574035] TCP reno registered
[  538.574066] UDP hash table entries: 256 (order: 0, 4096 bytes)
[  538.574096] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[  538.574371] NET: Registered protocol family 1
[  538.574829] RPC: Registered udp transport module.
[  538.574859] RPC: Registered tcp transport module.
[  538.574890] RPC: Registered tcp NFSv4.1 backchannel transport module.
[  538.575775] omap-iommu omap-iommu.0: isp registered
[  538.577514] VFS: Disk quotas dquot_6.5.2
[  538.577636] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[  538.578735] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[  538.579559] JFFS2 version 2.2. (NAND) (SUMMARY)  �© 2001-2006 Red Hat, Inc.
[  538.580444] msgmni has been set to 969
[  538.584197] alg: No test for stdrng (krng)
[  538.584503] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[  538.584564] io scheduler noop registered
[  538.584594] io scheduler deadline registered
[  538.584747] io scheduler cfq registered (default)
[  538.643615] OMAP DSS rev 2.0
[  538.643676] OMAP DISPC rev 3.0
[  538.643768] OMAP VENC rev 2
[  538.644012] OMAP DSI rev 1.0
[  538.980529] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[  538.998168] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
[  539.015136] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
[  539.032073] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
[  539.608154] console [ttyS2] enabled
[  539.618347] brd: module loaded
[  539.624694] loop: module loaded
[  539.629302] omap2-nand driver initializing
[  539.633697] No NAND device found!!!
[  539.637420] No NAND device found!!!
[  539.641937] usbcore: registered new interface driver catc
[  539.647460] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
[  539.653533] usbcore: registered new interface driver kaweth
[  539.659210] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[  539.666839] usbcore: registered new interface driver pegasus
[  539.672607] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
[  539.679626] usbcore: registered new interface driver rtl8150
[  539.685455] usbcore: registered new interface driver asix
[  539.690979] usbcore: registered new interface driver cdc_ether
[  539.696960] usbcore: registered new interface driver dm9601
[  539.702697] usbcore: registered new interface driver smsc95xx
[  539.708618] usbcore: registered new interface driver gl620a
[  539.714355] usbcore: registered new interface driver net1080
[  539.720123] usbcore: registered new interface driver plusb
[  539.725769] usbcore: registered new interface driver rndis_host
[  539.731842] usbcore: registered new interface driver cdc_subset
[  539.737915] usbcore: registered new interface driver zaurus
[  539.743621] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[  539.751708] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[  539.758575] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[  539.764617] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
[  539.772247] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[  539.791931] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[  539.797851] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[  539.804718] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[  539.812042] usb usb2: Product: OMAP-EHCI Host Controller
[  539.817443] usb usb2: Manufacturer: Linux 2.6.32 ehci_hcd
[  539.822906] usb usb2: SerialNumber: ehci-omap.0
[  539.828155] hub 2-0:1.0: USB hub found
[  539.832031] hub 2-0:1.0: 3 ports detected
[  539.862365] Initializing USB Mass Storage driver...
[  539.867462] usbcore: registered new interface driver usb-storage
[  539.873565] USB Mass Storage support registered.
[  539.878601] mice: PS/2 mouse device common for all mice
[  539.884277] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[  539.892120] input: twl4030_pwrbutton as /devices/platform/i2c_omap.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1
[  539.902862] i2c /dev entries driver
[  539.906982] Linux video capture interface: v2.00
[  539.911987] omap-iommu omap-iommu.0: isp: version 1.1
[  539.918670] vpfe_init
[  539.921539] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[  539.928344] cpuidle: using governor ladder
[  539.932556] cpuidle: using governor menu
[  540.042205] mmci-omap-hs mmci-omap-hs.1: err -16 configuring card detect
[  540.049285] Registered led device: beagleboard::usr0
[  540.054473] Registered led device: beagleboard::usr1
[  540.061004] Registered led device: beagleboard::pmu_stat
[  540.068115] usbcore: registered new interface driver usbhid
[  540.073822] usbhid: USB HID core driver
[  540.077880] Advanced Linux Sound Architecture Driver Version 1.0.21.
[  540.084808] usbcore: registered new interface driver snd-usb-audio
[  540.098266] hub 2-0:1.0: unable to enumerate USB device on port 2
[  540.159698] No device for DAI omap-mcbsp-dai-0
[  540.164215] No device for DAI omap-mcbsp-dai-1
[  540.168731] No device for DAI omap-mcbsp-dai-2
[  540.173217] No device for DAI omap-mcbsp-dai-3
[  540.177734] No device for DAI omap-mcbsp-dai-4
[  540.182220] OMAP3 Beagle SoC init
[  540.186401] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
[  540.197845] ALSA device list:
[  540.200927]   #0: omap3beagle (twl4030)
[  540.204895] oprofile: using arm/armv7
[  540.208862] TCP cubic registered
[  540.212127] NET: Registered protocol family 17
[  540.216705] NET: Registered protocol family 15
[  540.221282] lib80211: common routines for IEEE802.11 drivers
[  540.227050] ThumbEE CPU extension supported.
[  540.231384] Power Management for TI OMAP3.
[  540.236724] SmartReflex driver initialized
[  540.241058] omap3beaglelmb: Driver registration complete
[  540.254882] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[  540.263153] registered taskstats version 1
[  540.391418] Console: switching to colour frame buffer device 160x45
[  540.413146] regulator_init_complete: incomplete constraints, leaving VAUX4 on
[  540.420745] regulator_init_complete: incomplete constraints, leaving VAUX3 on
[  540.428558] regulator_init_complete: incomplete constraints, leaving VDAC on
[  540.436676] omap_vout omap_vout: probed for an unknown device
[  540.442993] Waiting for root device /dev/mmcblk0p2...
[  540.463989] mmc0: host does not support reading read-only switch. assuming write-enable.
[  540.472351] mmc0: new high speed SDHC card at address 1234
[  540.478332] mmcblk0: mmc0:1234 SA04G 3.67 GiB
[  540.483215]  mmcblk0: p1 p2
[  540.565704] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended
[  540.575256] kjournald starting.  Commit interval 5 seconds
[  540.592285] EXT3-fs (mmcblk0p2): using internal journal
[  540.601226] EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
[  540.612060] VFS: Mounted root (ext3 filesystem) on device 179:2.
[  540.626342] devtmpfs: mounted
[  540.633087] Freeing init memory: 204K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
[  542.523193] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[  542.931213] twl_rtc twl_rtc: Power up reset detected.
[  543.210510] twl_rtc twl_rtc: Enabling TWL-RTC.
[  543.598754] mt9p031 2-0048: Unable to detect sensor
Remounting root file system...
Caching udev devnodes
Populating dev cache
[  556.246765] Bluetooth: Core ver 2.15
[  556.251312] NET: Registered protocol family 31
[  556.255859] Bluetooth: HCI device and connection manager initialized
[  556.262268] Bluetooth: HCI socket layer initialized
[  556.284057] Bluetooth: L2CAP ver 2.14
[  556.287811] Bluetooth: L2CAP socket layer initialized
[  556.312377] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[  556.429931] NET: Registered protocol family 10
[  556.496398] NET: Registered protocol family 23
[  556.519653] IrCOMM protocol (Dag Brattli)
[  556.622680] Bluetooth: RFCOMM TTY layer initialized
[  556.627624] Bluetooth: RFCOMM socket layer initialized
[  556.632904] Bluetooth: RFCOMM ver 1.11
ALSA: Restoring mixer settings...
Cleaning: /etc/network/run/ifstate.
Configuring network interfaces... eth0: unknown interface: No such device
eth0: unknown interface: No such device
eth0      No such device

SIOCSIFADDR: No such device
eth0: unknown interface: No such device
eth0: unknown interface: No such device
Failed to bring up eth0.
usb0: unknown interface: No such device
usb0: unknown interface: No such device
usb0      No such device

SIOCSIFADDR: No such device
usb0: unknown interface: No such device
usb0: unknown interface: No such device
Failed to bring up usb0.
done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
Mon Feb 20 11:01:00 GMT 2012
INIT: Entering runlevel: 5
Starting system message bus: dbus.
Starting Hardware abstraction layer hald
Configuring leds:
  beagleboard::pmu_stat: none
  beagleboard::usr0: heartbeat
  beagleboard::usr1: mmc0
Starting Dropbear SSH server: dropbear.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting Distributed Compiler Daemon: distcc.
Starting Samba: smbd nmbd.
Starting syslog-ng:.
[ ok ]rting Avahi mDNS/DNS-SD Daemon: avahi-daemon
Starting Network connection manager daemon: NetworkManager.
cups: started scheduler.
Starting GPE display manager: gpe-dm

.-------.
|       |                  .-.
|   |   |-----.-----.-----.| |   .----..-----.-----.
|       |     | __  |  ---'| '--.|  .-'|     |     |
|   |   |  |  |     |---  ||  --'|  |  |  '  | | | |
'---'---'--'--'--.  |-----''----''--'  '-----'-'-'-'
                -'  |
                '---'

The Angstrom Distribution beagleboard ttyS2

Angstrom 2010.7-test-20110220 beagleboard ttyS2

beagleboard login: