NSA310>> run to_stock
Saving Environment to NAND...
Erasing Nand...Writing to Nand... done
�
         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Jun  8 2011 - 18:48:37) Marvell version: 3.4.19

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFEE0

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
Kernel address is 0x4640000.

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net:   egiga0, egiga1 [PRIME]
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x4640000, size 0xa00000

Reading data from 0x503f800 -- 100% complete.
 10485760 bytes read: OK
## Booting image at 02000000 ...
   Image Name:   Linux-2.6.31.8
   Created:      2013-03-27   8:44:10 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    6061900 Bytes =  5.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux...................................................................................................................................
Linux version 2.6.31.8 (root@Neo) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #2 Wed Mar 27 16:43:46 CST 2013
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 65024
Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA0000t
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 244608KB available (5300K code, 300K data, 3164K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1199.30 BogoMIPS (lpj=5996544)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size   1MB
PEX1_MEM ....no such
PEX1_IO ....no such
INTER_REGS ....base f1000000, size   1MB
NFLASH_CS ....base fa000000, size   2MB
SPI_CS ....base f4000000, size  16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB

  Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- RD-88F6281A  Soc: 88F6281 A1 LE

 Detected Tclk 200000000 and SysClk 400000000
Marvell USB EHCI Host controller #0: c8040740
PEX0 interface detected Link X1
pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:01.0: PME# disabled
PCI: bus0: Fast back to back transfers disabled
mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
cpufreq: Init kirkwood cpufreq driver
XOR registered 4 channels
XOR 2nd invalidate WA enabled
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
gpio_dev = fd00000
LED_SET_CTL_IOC_NUM= 6702
High gpio polarity = 50
High gpio polarity = 70
Enable Interrupt
mv88f6281_wdt: Watchdog Timer timeout = 8 sec.
mv88f6281_wdt: HW Watchdog timeout    = 15 sec.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 [email protected]).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.12)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 478
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
Wake up disk0......
Wake up disk1......
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access     Seagate  ST9250315AS      0001 PQ: 0 ANSI: 5
EnablePowerSaving
PowerSavingTime = 15
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] 0-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: Attached scsi generic sg0 type 0
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o 0 Giga ports supported
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o TCP segmentation offload (TSO) supported
  o Large Receive offload (LRO) supported
  o Receive checksum offload supported
  o Transmit checksum offload supported
  o Network Fast Processing (Routing) supported - (Disabled)
  o Driver ERROR statistics enabled
  o Proc tool API enabled
  o SKB Reuse supported - (Disabled)
  o SKB Recycle supported - (Disabled)
  o Rx descripors: q0=128
  o Tx descripors: q0=532
  o Loading network interface(s):

mvFpRuleDb (c8d9c000): 2048 entries, 8192 bytes
Counter=0, opIdx=6, overhead=16
Counter=1, opIdx=2, overhead=0
Counter=2, opIdx=1, overhead=18
Counter=3, opIdx=2, overhead=0
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 693 at 0x0000056a0000
Bad eraseblock 919 at 0x0000072e0000
Bad eraseblock 948 at 0x000007680000
9 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 9 MTD partitions on "nand_mtd":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000180000 : "uboot_env"
 sda:
0x000000180000-0x000000200000 : "key_store"
0x000000200000-0x000000280000 : "info"
0x000000280000-0x000000c80000 : "etc"
0x000000c80000-0x000001680000 : "kernel_1"
0x000001680000-0x000004640000 : "rootfs1"
0x000004640000-0x000005040000 : "kernel_2"
0x000005040000-0x000008000000 : "rootfs2"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
hwmon-vid: Unknown VRM version of your CPU
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc mv_rtc: setting system clock to 2013-05-21 12:55:36 UTC (1369140936)
 sda1 sda2
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] Attached SCSI disk
Freeing init memory: 3164K
*** Stage 1: Setup system and device drivers ***
usb 1-1: new high speed USB device using ehci_marvell and address 2
In hub_port_init, and number is 0, retry 0, port 1 .....
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
r8168 Gigabit Ethernet driver 8.023.00-NAPI loaded
r8168 0000:00:01.0: no MSI. Back to INTx.
 Set LED ...
eth%d: RTL8168B/8111B at 0xd0900000, c8:6c:87:0a:f3:b1, IRQ 9
r8168: This product is covered by one or more of the following patents: US5,307,459, US5,434,872, US5,732,094, US6,570,884, US6,115,776, and US6,327,.
r8168  Copyright (C) 2011  Realtek NIC software team <[email protected]>
 This program comes with ABSOLUTELY NO WARRANTY; for details, please see <http://www.gnu.org/licenses/>.
 This is free software, and you are welcome to redistribute it under certain conditions; see <http://www.gnu.org/licenses/>.
r8168: egiga0: link down
ADDRCONF(NETDEV_UP): egiga0: link is not ready
*** Stage 2: Prepare the root file system ***
Mount system partition...
yaffs: dev is 32505864 name is "mtdblock8" ro
yaffs: passed flags ""
bsname}: no internal volume available
1
WARNING: No valid partition on HDD or no HDD plugged!
WARNING: No valid partition on HDD or no HDD plugged
Boot from RAM disk
r8168: egiga0: link up
ADDRCONF(NETDEV_CHANGE): egiga0: link becomes ready
r8168: egiga0: link up
Mount system disk image ...
yaffs: dev is 32505860 name is "mtdblock4" rw
yaffs: passed flags ""
/etc/zyxel/conf exist..
Start rcS2 of ZyXEL style
*** Stage 3: Start services on HDD ***
NTFS driver 2.1.29 [Flags: R/O MODULE].
tntfs: module license 'Commercial. For support email [email protected].' taints kernel.
Disabling lock debugging due to kernel taint
Tuxera NTFS driver 3011.12.23 [Flags: R/W MODULE].
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
PPP Deflate Compression module registered
NET: Registered protocol family 24
PPP BSD Compression module registered
modprobe: module fuse not found in modules.dep
fanspeed 1871 , pwm value 88
fanspeed 1871 , pwm value 96
fanspeed 1896 , pwm value 104
fanspeed 1896 , pwm value 112
Starting PID Fan Control..
P:20, I:1, D:5, SampleRate:10 seconds, ST_CPU:46, ST_ADT7463:46, ST_DauBoard:46
Wt_CPU:0, Wt_ADT7463:0, Wt_DauBoard:1
Tolerance:1 MinPwm:0x40

sda
checking sda
Trying to mount /dev/sda1
mount: wrong fs type, bad option, bad superblock on /dev/sda1,
       missing codepage or helper program, or other error
       In some cases useful info is found in syslog - try
       dmesg | tail  or so

Fail to mount /dev/sda1
Press ENTER to continue...
Starting zylogd...
 zylog starts.
Starting uamd...
Starting ZySH daemon and client...
Start NSA-220 system daemon....
 Start ZySH daemon
zyshd: version 2.0.0 (build: 16:18:09 Mar 27 2013)
% zylog init start
cat: can't open '/var/run/syslog-ng.pid': No such file or directory
Try to KILL SIGHUP to syslog-ng: pid=0
syslog-ng not running, start /usr/sbin/syslog-ng
May 21 12:56:06 (none) syslog-ng[1377]: syslog-ng starting up; version='2.0.10'
zyio_open_config success. (/etc/__system_default.xml, 0)
zyio_open_config success. (/etc/zyxel/conf/__system_default_device_ha.xml, 0)
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
/bin/ln -s -f /etc/MyZone /etc/localtime
/bin/hostname nsa310
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-r] [-n] [-v] special | node...
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-r] [-n] [-v] special | node...
BusyBox v1.17.2 (2013-03-27 16:11:13 CST) multi-call binary.

Usage: rmdir [OPTIONS] DIRECTORY...

Init SMB DB access...
rm: can't remove '/var/log/samba/smb.db': No such file or directory
zyio_container_create_template(/etc/__system_default.xml): scope:[network/wlan] list:[wlan_list] type:[wlan_t] is not existed
Assemble volume....
[1420] server write-only FIFO is opened (fd=6)
[1420] server read-only FIFO is opened (fd=7)
[1420] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 278
 Startup config
POLLHUP on 7
  pid = 1420
[1420] is disconnected
[1519] server write-only FIFO is opened (fd=6)
[1519] server read-only FIFO is opened (fd=7)
[1519] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 14
argc = 1,  func = 17
argc = 1,  func = 666
argc = 2,  func = 105
argid[1]: 1078; argv[1]: ge1
argc = 5,  func = 108
argid[1]: 1078; argv[1]: ge1
argid[2]: 313; argv[2]: ip
argid[3]: 435; argv[3]: address
argid[4]: 539; argv[4]: dhcp
argc = 3,  func = 106
argid[1]: 1078; argv[1]: ge1
argid[2]: 350; argv[2]: exit
argc = 2,  func = 441
argid[1]: 1071; argv[1]: 113.114.1.1
argc = 4,  func = 443
argid[1]: 876; argv[1]: fetch
argid[2]: 629; argv[2]: auto
argid[3]: 1078; argv[3]: ge1
/bin/rm -f /var/zyxel/zysh/egiga0.metric
/bin/ip route del default via 0.0.0.0 dev egiga0
RTNETLINK answers: No such process
ADDRCONF(NETDEV_CHANGE): egiga0: link becomes ready
May 21 12:56:16 (none) dhcpcd[1554]: dhcpT1value is 43200 sec
May 21 12:56:16 (none) dhcpcd[1554]: dhcpT2value is 75600 sec
[1531] server write-only FIFO is opened (fd=9)
[1531] server read-only FIFO is opened (fd=10)
[1531] server error read-only FIFO is opened (fd=11)
[1568] server write-only FIFO is opened (fd=12)
[1568] server read-only FIFO is opened (fd=13)
[1568] server error read-only FIFO is opened (fd=14)
argc = 7,  func = 78
argid[1]: 267; argv[1]: mail
argid[2]: 1397; argv[2]: 1
argid[3]: 436; argv[3]: category
argid[4]: 375; argv[4]: all
argid[5]: 462; argv[5]: level
argid[6]: 479; argv[6]: alert
mail server '1' log_category(all) is:alert
argc = 1,  func = 442
POLLHUP on 10
  pid = 1531
[1531] is disconnected
argc = 7,  func = 78
argid[1]: 267; argv[1]: mail
argid[2]: 1397; argv[2]: 1
argid[3]: 436; argv[3]: category
argid[4]: 375; argv[4]: all
argid[5]: 462; argv[5]: level
argid[6]: 375; argv[6]: all
mail server '1' log_category(all) is:all
argc = 3,  func = 444
argid[1]: 1078; argv[1]: ge1
argid[2]: 1071; argv[2]: 192.168.1.1
POLLHUP on 13
  pid = 1568
[1568] is disconnected
argc = 2,  func = 69
argid[1]: 1070; argv[1]: time.stdtime.gov.tw
argc = 2,  func = 61
argid[1]: 1121; argv[1]: +0800
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
/bin/ln -s -f /etc/MyZone /etc/localtime
argc = 1,  func = 73
/usr/sbin/ntpdate_agent time.stdtime.gov.tw
[1575] server write-only FIFO is opened (fd=9)
[1575] server read-only FIFO is opened (fd=10)
[1575] server error read-only FIFO is opened (fd=11)
argc = 4,  func = 344
argid[1]: 1214; argv[1]: ""
argid[2]: 594; argv[2]: in
argid[3]: 1215; argv[3]: "NULL"
argc = 1,  func = 445
POLLHUP on 10
  pid = 1575
[1575] is disconnected
argc = 1,  func = 39
killall: pure-ftpd: no process killed
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-r] [-n] [-v] special | node...
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-r] [-n] [-v] special | node...
BusyBox v1.17.2 (2013-03-27 16:11:13 CST) multi-call binary.

Usage: rmdir [OPTIONS] DIRECTORY...

argc = 2,  func = 193
argid[1]: 1131; argv[1]: "admin"
argc = 5,  func = 194
argid[1]: 1131; argv[1]: "admin"
argid[2]: 1408; argv[2]: 501
argid[3]: 363; argv[3]: password
argid[4]: 1154; argv[4]: AC804745EE68EBEA19F10A933D4868DC:68BBBB18B3C27D941CB6224353BE1D0A
enter smb_db_update_user
argc = 5,  func = 194
argid[1]: 1131; argv[1]: "admin"
argid[2]: 1408; argv[2]: 501
argid[3]: 634; argv[3]: type
argid[4]: 635; argv[4]: admin
enter smb_db_update_user
argc = 5,  func = 195
argid[1]: 1131; argv[1]: "admin"
argid[2]: 1408; argv[2]: 501
argid[3]: 639; argv[3]: shpass
argid[4]: 1157; argv[4]:  $1$$RnH2L3nVFrie6slQ1KCDV1
shpass : $1$$RnH2L3nVFrie6slQ1KCDV1
argc = 4,  func = 190
argid[1]: 1131; argv[1]: "admin"
argid[2]: 1408; argv[2]: 501
argid[3]: 350; argv[3]: exit
argc = 6,  func = 175
argid[1]: 457; argv[1]: share
argid[2]: 627; argv[2]: save
argid[3]: 1159; argv[3]: "public"
argid[4]: 396; argv[4]: path
argid[5]: 1161; argv[5]: "/i-data/md0/public"
folder is not under mount point.
argc = 7,  func = 164
argid[1]: 457; argv[1]: share
argid[2]: 627; argv[2]: save
argid[3]: 1159; argv[3]: "public"
argid[4]: 396; argv[4]: path
argid[5]: 1161; argv[5]: "/i-data/md0/public"
argid[6]: 350; argv[6]: exit
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2213 Close file ok
argc = 6,  func = 175
argid[1]: 457; argv[1]: share
argid[2]: 627; argv[2]: save
argid[3]: 1159; argv[3]: "video"
argid[4]: 396; argv[4]: path
argid[5]: 1161; argv[5]: "/i-data/md0/video"
folder is not under mount point.
argc = 7,  func = 176
argid[1]: 457; argv[1]: share
argid[2]: 627; argv[2]: save
argid[3]: 1159; argv[3]: "video"
argid[4]: 396; argv[4]: path
argid[5]: 1161; argv[5]: "/i-data/md0/video"
argid[6]: 613; argv[6]: media-server
argc = 7,  func = 164
argid[1]: 457; argv[1]: share
argid[2]: 627; argv[2]: save
argid[3]: 1159; argv[3]: "video"
argid[4]: 396; argv[4]: path
argid[5]: 1161; argv[5]: "/i-data/md0/video"
argid[6]: 350; argv[6]: exit
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2213 Close file ok
argc = 6,  func = 175
argid[1]: 457; argv[1]: share
argid[2]: 627; argv[2]: save
argid[3]: 1159; argv[3]: "photo"
argid[4]: 396; argv[4]: path
argid[5]: 1161; argv[5]: "/i-data/md0/photo"
folder is not under mount point.
argc = 7,  func = 176
argid[1]: 457; argv[1]: share
argid[2]: 627; argv[2]: save
argid[3]: 1159; argv[3]: "photo"
argid[4]: 396; argv[4]: path
argid[5]: 1161; argv[5]: "/i-data/md0/photo"
argid[6]: 613; argv[6]: media-server
argc = 7,  func = 164
argid[1]: 457; argv[1]: share
argid[2]: 627; argv[2]: save
argid[3]: 1159; argv[3]: "photo"
argid[4]: 396; argv[4]: path
argid[5]: 1161; argv[5]: "/i-data/md0/photo"
argid[6]: 350; argv[6]: exit
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2213 Close file ok
argc = 6,  func = 175
argid[1]: 457; argv[1]: share
argid[2]: 627; argv[2]: save
argid[3]: 1159; argv[3]: "music"
argid[4]: 396; argv[4]: path
argid[5]: 1161; argv[5]: "/i-data/md0/music"
folder is not under mount point.
argc = 7,  func = 176
argid[1]: 457; argv[1]: share
argid[2]: 627; argv[2]: save
argid[3]: 1159; argv[3]: "music"
argid[4]: 396; argv[4]: path
argid[5]: 1161; argv[5]: "/i-data/md0/music"
argid[6]: 613; argv[6]: media-server
argc = 7,  func = 164
argid[1]: 457; argv[1]: share
argid[2]: 627; argv[2]: save
argid[3]: 1159; argv[3]: "music"
argid[4]: 396; argv[4]: path
argid[5]: 1161; argv[5]: "/i-data/md0/music"
argid[6]: 350; argv[6]: exit
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2213 Close file ok
argc = 6,  func = 175
argid[1]: 457; argv[1]: share
argid[2]: 627; argv[2]: save
argid[3]: 1159; argv[3]: "admin"
argid[4]: 396; argv[4]: path
argid[5]: 1161; argv[5]: "/i-data/md0/admin"
folder is not under mount point.
argc = 7,  func = 164
argid[1]: 457; argv[1]: share
argid[2]: 627; argv[2]: save
argid[3]: 1159; argv[3]: "admin"
argid[4]: 396; argv[4]: path
argid[5]: 1161; argv[5]: "/i-data/md0/admin"
argid[6]: 350; argv[6]: exit
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2213 Close file ok
argc = 4,  func = 411
argid[1]: 1240; argv[1]: yes
argid[2]: 1241; argv[2]: yes
argid[3]: 1242; argv[3]: yes
May 21 20:56:19 (none) ntpdate[1586]: step time server 59.124.196.84 offset 1.559753 sec
argc = 2,  func DisablePowerSaving
= 147
argid[1]:TimerState = 1
 1146; argv[1]: EnablePowerSaving
15
PowerSavingTime = 15
test0
Test1
Test2
Test3:
argc = 2,  func = 670
argid[1]: 1078; argv[1]: ge1
killall: httpd: no process killed
May 21 20:56:23 (none) httpd[1747]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
May 21 20:56:23 (none) httpd[1747]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
May 21 20:56:23 (none) httpd[1747]: [warn] RSA server certificate CommonName (CN) `nsa310' does NOT match server name!?
May 21 20:56:23 (none) httpd[1747]: [error] mod_auth_zyxel: initialized.
argc = 2,  func = 161
argid[1]: 1151; argv[1]: g
exec_cmd complete
eth status = Wake-onpumbg
ethtest0
Test1
Test2
Test3:
eth cmd = /sbin/ethtool -s egiga0 wol g
argc = 2,  func = 18
argid[1]: 350; argv[1]: exit
argc = 1,  func = 20
POLLHUP on 7
  pid = 1519
[1519] is disconnected
configure terminal ip smb internal disable "/i-data/md0"
[1760] server write-only FIFO is opened (fd=6)
[1760] server read-only FIFO is opened (fd=7)
[1760] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 182
argid[1]: 631; argv[1]: internal
argid[2]: 303; argv[2]: disable
argid[3]: 1173; argv[3]: "/i-data/md0"
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2213 Close file ok
no such autosata.
Error happens when deleting autosata.
POLLHUP on 7
  pid = 1760
[1760] is disconnected
configure terminal ip smb internal disable "/i-data/md1"
[1765] server write-only FIFO is opened (fd=6)
[1765] server read-only FIFO is opened (fd=7)
[1765] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 182
argid[1]: 631; argv[1]: internal
argid[2]: 303; argv[2]: disable
argid[3]: 1173; argv[3]: "/i-data/md1"
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2213 Close file ok
no such autosata.
Error happens when deleting autosata.
POLLHUP on 7
  pid = 1765
[1765] is disconnected
no volume exist...
configure terminal ip smb internal disable "/i-data/md0"
[1781] server write-only FIFO is opened (fd=6)
[1781] server read-only FIFO is opened (fd=7)
[1781] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 182
argid[1]: 631; argv[1]: internal
argid[2]: 303; argv[2]: disable
argid[3]: 1173; argv[3]: "/i-data/md0"
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2213 Close file ok
no such autosata.
Error happens when deleting autosata.
POLLHUP on 7
  pid = 1781
[1781] is disconnected
Starting smbd...
May 21 20:56:25 (none) httpd[1748]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
May 21 20:56:25 (none) httpd[1748]: [warn] RSA server certificate CommonName (CN) `nsa310' does NOT match server name!?
May 21 20:56:25 (none) httpd[1748]: [error] mod_auth_zyxel: initialized.
Starting nmbd...
Starting NSU Agent...
configure terminal ip smb internal disable "/i-data/md1"
[1813] server write-only FIFO is opened (fd=6)
[1813] server read-only FIFO is opened (fd=7)
[1813] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 182
argid[1]: 631; argv[1]: internal
argid[2]: 303; argv[2]: disable
argid[3]: 1173; argv[3]: "/i-data/md1"
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2213 Close file ok
no such autosata.
Error happens when deleting autosata.
POLLHUP on 7
  pid = 1813
[1813] is disconnected
Starting copy auto daylight saving tzfile to /i-data/.system/ ...
cp -a /usr/local/zoneinfo /i-data/.system/
grep: /proc/nas_model: No such file or directory
storage_gen_swap.sh: not enough space to dd swap file
GMT offset=28800s
setting system time zone to tz_minuteswest=-480
mknod: /dev/btncpy: File exists
setLED COPY OFF
led_state_map_addr = 10
[2241] server write-only FIFO is opened (fd=6)
[2241] server read-only FIFO is opened (fd=7)
[2241] server error read-only FIFO is opened (fd=8)
argc = 2,  func = 349
argid[1]: 1216; argv[1]: former
POLLHUP on 7
  pid = 2241
[2241] is disconnected
schedule_controller is already running now.
Starting "/etc/init.d/zypkg_controller.sh".
Starting to set up zy-pkgs environment ...
-> No volume exists now. zy-pkgs will not work.
mount: wrong fs type, bad option, bad superblock on /i-data/.system/web_cache,
       missing codepage or helper program, or other error
       In some cases useful info is found in syslog - try
       dmesg | tail  or so

chmod: /usr/local/apache/web_framework/data/cache: Read-only file system
chmod: /usr/local/apache/web_framework/data/cache: Read-only file system
Web Server already started.
mkdir: can't create directory '/i-data/md0/': No such file or directory
mkdir: can't create directory '/i-data/md0/': No such file or directory
/bin/nice: /usr/sbin/lld2d: No such file or directory
Starting app_wd...
 core_checksum : ca88367cbec5a3147b5cbf01303f78bb
 fwversion : 4.51(AFK.0)
 img_checksum : 5dccb899a27779651bf3004e7e9f99ef
 modelid : A203
 revision : 37977
 romfile_checksum : 89D4
 zld_checksum : e01e1f7b85e628b31e65b43b3997d087
led_state_map_addr = 46

Please press Enter to activate this console. /usr/lib/python2.6/site-packages/flickrapi/__init__.py:45: DeprecationWarning: the md5 module is deprecad



BusyBox v1.17.2 (2013-03-27 16:11:13 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ # May 21 12:56:35 (none) linuxrc: starting pid 2309, tty '': '-/bin/sh'

/ #