me steps inside the car as she drive it to the vehicle lift , parking it over it properly.
me turns off the car as she raises the handbrake making sure the car is setlled.
me extends her hand into the hood grip , pulling it up unlocking it.
me steps outside the car heading to the worktable as she grabs couple gloves wearing them.
me heads towards the hood again as she extends her hand under it , pulling it up.
do hood would be opened.
me leans over looking at the front bumper , examining it.
me heads to the worktable again as she leans over grabbing an air wrench of it.
me heads back to the car holding an air wrench with her right hand.
me connects the air wrench into the compressor as she goes to the hood leaning front of it.
me aims the air wrench at the two bolts holding the front grill on the top of it.
me applies pressure at the trigger as she unscrews the bolts on the top of the grill.
me drops the grill at the ground.
do grill would be removed.
me stands up pushing the button to raise the car lift abit higher.
me extends her hand with the air wrench throught the center honeycomb-.
do in the lower section of the bumper,aiming at the two bolts in there.
me applies pressure at the trigger as she unscrews the bolts .
me lays underneath the car again as she aims at the 16 screws holding the dust shield one by one.
me applies pressure at the trigger as she unscrews the bolts one by one.
me changes her aiming and vision into the wheel liners holding the bumper , unscrewing the bolts of them-,
do of each side .
me aims at the screw on each side that is connecting the bumper to the front fenders , unscrewing them.
me drops all the screws to the ground beside the car as she aims at the screw holding the upper portion of-.
do the wheel liner to the front bumper.
me aims her air wrench again at the bolts positioned right in the center of the bumper.
do the area where the grill originally covered.
me unscrews the bolts on there as she holds the bumper with her partner , dropping it on the ground.
me lays beneath the engine again .
me grabs the wrench off the ground as she aims it at the pulley on the front of the balancer.
me applies pressure at the trigger unscrewing it.
me aims her wrench again at the harmonic balancer screws from the front of the crankshaft.
me applies pressure at the trigger unscrewing them.
me extends her hands removing the engine drive belts from harmonic balancer.
me extends her hands again as she disconnects all the water hoses along with the water pump.
me grabs the air wrench off the ground again as she aims at the timing chain's bolts unscrewing them.
do draining the oil of them in a bucket
do crankshaft would be visible .
me extends her hand into the oil bump disconnecting rod caps of it.
me holds the crankshaft while removing the last rod cap , as she grabs it when it is loosened.
me drops the old crankshaft on the ground as she heads to the trunk opening it-.
do grabbing the new crankshaft along with the piston of it afterwards.
me lays beneath the car with the crankshaft/piston as she places them on position , holding them with her left hand-.
do as she grabs the rod caps , placing them on the new crankshaft using a socket to tighten them.
me extends her hands connecting all the water hoses back in.
me grabs the engine drive belts from the ground placing them at the harmonic balancer.
me tightens the pulley on the front of the balancer , making sure it's settled.
do new crankshaft would be installed.
me stands up as she runs toward the wroktable grabbing a penetrating lubricant of it.
me heads back to the vehicle as she sprays the nuts and bolts on the exhaust manifold with it.
me drops the penetrating lubricant at the ground as she extends her hand into the hood-.
do disconnecting the negative battery cable.
me presses on the lift button highering it , making sure she is still able to access the exhaust manifold-.
do from the top of the enigne bay.
me grabs the air wrench of the ground as she lays underneath the hood , searching where-.
do the exhaust manifold meets the rest of the exhaust as she aims her wrench at their bolts-.
do unscrewing the bolts that are holding the pipes together.
me extends her hand again into the piping loosening the champ holding the intake piping to the throttle body-.
do removing the piping.
me extends her wrench into the exhaust manifold's bolts aiming at them as she applies-.
do pressure at the trigger , removing them one by one.
me hooks up the winch with the exhaust manifold to hold it's weight before removing the last bolt.
do lifts up the manifold with the winch from the enigne bay as she drops it in the ground.
me extends her hands in as she drains the oil from the oil pan again.
me grabs a 13mm wrench as she aims it at the bolts of the horn on the passenger side from it's bracket-.
do flipping the horn over so its on the top side of the bracket then starts bolting it back down.
me grabs few sheetmetal screws as she palces them on the mounting blocks , tightening them -.
do as she pulls the wiring harness down below the mounting blocks.
me slides her hand into her toolsbelt as she grabs a razor knife of it , cutting factory-.
do air guidance flaps from both sides of the shroud.
me grabs the new intercooler off the trunk as she mounts it to the mounting blocks.
me grabs the new turbo off the trunk with a winch placing it close by the manifold with a gasket between them.
me places the bolts on the turbo charger as she tightens them with an air wrench.
me extends her hands again attaching all oil and coolant lines to the turbo.
me leans over as she starts looking if the exchaust manifold gasket is in the right place-,
do fastening the manifold to the engine.
me extends her hands into the hood again connecting the oil and cooland feed as she returns the-.
do lines from the turbo to the engine.
me extends her hands in again , fastening the intercooler pipe to the new turbo as she-.
do connects the other end of the intercooler pipe coming from the turbo to the intercooler.
me connects the other intercooler pipe to the other side of the intercooler , fastening the intake-.
do pipe to the turbo.
me grabs few bolts off the ground as she mount places them to the downpipe down to the exhaust-.
do side of the turbo , using her air wrench to tighten them.
do bolts the other end of the exhaust the same way she did to the first one.
me presses on the lift button as she lowers the car lift.
me extends her hand into the injector removing the electrical connector of it-.
do releasing the safety clip of it.
me leans over grabbing an air wrench off the ground as she unscrews the mounting bolts-.
do located on each comer of the fuel rail.
me gently lifts up the fuel rail from the intake manifold as she drops it in the ground-.
do allowing the fuel injector to be removed .
me applies pressure downward to the fuel injector from the rail, poping the injector-.
do from the o ring seal located on either end of the injector.
me removes the fuel injector as she starts inspecting it for both sealing 0 ring-.
do which can get stuck in the rail or down in the intake manifold.
me moves to the work table as she drops the fuel injector in there beside the new one-.
do matching them both .
me sprays the new o ring seal of the new injector with lubricant as she-,
do gently installs watching the o ring seals.
me starts gently pushing down on the rail while aligning the remaining enjectors.
me grabs few rail mounting bolts as she places them on the injector-.
do tightening them with the wrench , making sure they are all in.
me grabs the electrical connector she removed as she reconnects it back to the fuel injector.
do fuel injector would be installed.
me leans over checking if all the bolts were tightened before she grabs the bumper and grill-.
do off the ground placing them on the front as she tightens the bolts on it .
me presses the lift button , highering it up abit as she leans underneath the hood mounting back-.
do all the bolts she removed off the bumper.
do Mia would clearly look sweaty and tired.
me leans over slowly as she grabs an air wrench off the ground , aiming it at the battery's bolts.
me applies pressure at the trigger as she unscrews the battery , lifting it up then dropping it on the ground.
do she would go take a nap for about 30minutes , leaving the car unplugged.
me goes back to the work table after a nap grabbing the ecu then heads back to the car.
me installs the new ecu carefully as she places the battery back , reconnecting it.
me grabs a bucket of fuel as she pours some fuel carefully .
me heads back to the hood re-connecting the negative battery cable.
me steps inside the car as she turns the key to auxiliary position , checking if there is-.
do 'check engine' light on , means the ecu is in working condition.
me takes the car off the lift , stepping out to close the hood afterwards-.
do leaving it parked with handbrakes on.