Guest User

Untitled

a guest
Mar 6th, 2016
98
0
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 22.96 KB | None | 0 0
  1. # NOTE Lines must not exceed 132 characters
  2. # Robot module configurations : general handling of movement G-codes and slicing into moves
  3. default_feed_rate 4000 # Default rate ( mm/minute ) for G1/G2/G3 moves
  4. default_seek_rate 4000 # Default rate ( mm/minute ) for G0 moves
  5. mm_per_arc_segment 0.5 # Arcs are cut into segments ( lines ), this is the length for
  6. # these segments. Smaller values mean more resolution,
  7. # higher values mean faster computation
  8. #mm_per_line_segment 0.5 # Lines can be cut into segments ( not useful with cartesian
  9. # coordinates robots ).
  10. delta_segments_per_second 100 # for deltas only same as in Marlin/Delta, set to 0 to disable
  11. # and use mm_per_line_segment
  12.  
  13.  
  14. # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
  15. arm_solution linear_delta # selects the delta arm solution
  16. alpha_steps_per_mm 100 # Steps per mm for alpha stepper
  17. beta_steps_per_mm 100 # Steps per mm for beta stepper
  18. gamma_steps_per_mm 100 # Steps per mm for gamma stepper
  19.  
  20. arm_length 196.8 # this is the length of an arm from hinge to hinge
  21. arm_radius 101.9 # this is the horizontal distance from hinge to hinge
  22. # when the effector is centered
  23.  
  24. # Planner module configuration : Look-ahead and acceleration configuration
  25. planner_queue_size 32 # DO NOT CHANGE THIS UNLESS YOU KNOW EXACTLY WHAT YOU ARE DOING
  26. acceleration 3000 # Acceleration in mm/second/second.
  27. acceleration_ticks_per_second 1000 # Number of times per second the speed is updated
  28. junction_deviation 0.05 # Similar to the old "max_jerk", in millimeters,
  29. # Lower values mean being more careful, higher values means being
  30. # faster and have more jerk
  31. #minimum_planner_speed 0.0 # sets the minimum planner speed in mm/sec
  32.  
  33. # Stepper module configuration
  34. microseconds_per_step_pulse 1 # Duration of step pulses to stepper drivers, in microseconds
  35. minimum_steps_per_minute 1200 # Never step slower than this
  36. base_stepping_frequency 100000 # Base frequency for stepping, higher gives smoother movement
  37.  
  38. # Cartesian axis speed limits
  39. x_axis_max_speed 30000 # mm/min
  40. y_axis_max_speed 30000 # mm/min
  41. z_axis_max_speed 30000 # mm/min
  42.  
  43. # Stepper module pins ( ports, and pin numbers, appending "!" to the number will invert a pin )
  44. alpha_step_pin 2.0 # Pin for alpha stepper step signal
  45. alpha_dir_pin 0.5 # Pin for alpha stepper direction
  46. alpha_en_pin 0.4 # Pin for alpha enable pin
  47. alpha_max_rate 30000.0 # mm/min
  48.  
  49. beta_step_pin 2.1 # Pin for beta stepper step signal
  50. beta_dir_pin 0.11 # Pin for beta stepper direction
  51. beta_en_pin 0.10 # Pin for beta enable
  52. beta_max_rate 30000.0 # mm/min
  53.  
  54. gamma_step_pin 2.2 # Pin for gamma stepper step signal
  55. gamma_dir_pin 0.20 # Pin for gamma stepper direction
  56. gamma_en_pin 0.19 # Pin for gamma enable
  57. gamma_max_rate 30000.0 # mm/min
  58.  
  59. # Serial communications configuration ( transmission rate default to 9600 if undefined )
  60. uart0.baud_rate 115200 # Baud rate for the default hardware serial port
  61.  
  62. # Serial communications configuration ( baud rate default to 9600 if undefined )
  63. Serial.baud_rate 115200 # Baud rate for the default hardware serial port
  64. second_usb_serial_enable false # This enables a second usb serial port (to have both pronterface
  65. # and a terminal connected)
  66. leds_disable false # disable using leds after config loaded
  67. #msd_disable true # disable the MSD (USB SDCARD) when set to true
  68. #disable_msd true
  69. dfu_enable false
  70.  
  71. # Extruder module configuration
  72. extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
  73. extruder.hotend.steps_per_mm 506 # Steps per mm for extruder stepper
  74. extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  75. extruder.hotend.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  76. extruder.hotend.max_speed 200 # mm/s
  77.  
  78. extruder.hotend.step_pin 2.3 # Pin for extruder step signal
  79. extruder.hotend.dir_pin 0.22 # Pin for extruder dir signal
  80. extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
  81.  
  82. # extruder offset
  83. #extruder.hotend.x_offset 0 # x offset from origin in mm
  84. #extruder.hotend.y_offset 0 # y offset from origin in mm
  85. #extruder.hotend.z_offset 0 # z offset from origin in mm
  86.  
  87. # firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
  88. #extruder.hotend.retract_length 3 # retract length in mm
  89. #extruder.hotend.retract_feedrate 45 # retract feedrate in mm/sec
  90. #extruder.hotend.retract_recover_length 0 # additional length for recover
  91. #extruder.hotend.retract_recover_feedrate 8 # recover feedrate in mm/sec (should be less than retract feedrate)
  92. #extruder.hotend.retract_zlift_length 0 # zlift on retract in mm, 0 disables
  93. #extruder.hotend.retract_zlift_feedrate 6000 # zlift feedrate in mm/min (Note mm/min NOT mm/sec)
  94.  
  95. #delta_current 1.5 # First extruder stepper motor current
  96.  
  97. # Second extruder module configuration example
  98. extruder.hotend2.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
  99. extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper
  100. extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  101. extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  102. extruder.hotend2.max_speed 50 # mm/s
  103.  
  104. extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
  105. extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal
  106. extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
  107.  
  108. #extruder.hotend2.x_offset 0 # x offset from origin in mm
  109. #extruder.hotend2.y_offset 25.0 # y offset from origin in mm
  110. #extruder.hotend2.z_offset 0 # z offset from origin in mm
  111. #epsilon_current 1.5 # Second extruder stepper motor current
  112.  
  113. # Laser module configuration
  114. laser_module_enable false # Whether to activate the laser module at all. All configuration is
  115. # ignored if false.
  116. #laser_module_pin 2.5 # this pin will be PWMed to control the laser. Only P2.0 - P2.5
  117. # can be used since laser requires hardware PWM
  118. #laser_module_max_power 0.8 # this is the maximum duty cycle that will be applied to the laser
  119. #laser_module_tickle_power 0.0 # this duty cycle will be used for travel moves to keep the laser
  120. # active without actually burning
  121. #laser_module_pwm_period 20 # this sets the pwm frequency as the period in microseconds
  122.  
  123. # Hotend temperature control configuration
  124. temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all.
  125. # All configuration is ignored if false.
  126. temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
  127. temperature_control.hotend.heater_pin 2.4 # Pin that controls the heater
  128. temperature_control.hotend.thermistor EPCOS100K # see
  129. #temperature_control.hotend.beta 4066 # or set the beta value
  130.  
  131. temperature_control.hotend.set_m_code 104 #
  132. temperature_control.hotend.set_and_wait_m_code 109 #
  133. temperature_control.hotend.designator T #
  134.  
  135. #temperature_control.hotend.p_factor 13.7 # permanently set the PID values after an auto pid
  136. #temperature_control.hotend.i_factor 0.097 #
  137. #temperature_control.hotend.d_factor 24 #
  138.  
  139. #temperature_control.hotend.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
  140.  
  141. # Hotend2 temperature control configuration
  142. temperature_control.hotend2.enable true # Whether to activate this ( "hotend" ) module at all.
  143. # All configuration is ignored if false.
  144.  
  145. temperature_control.hotend2.thermistor_pin 0.24 # Pin for the thermistor to read
  146. temperature_control.hotend2.heater_pin 2.7 # Pin that controls the heater
  147. temperature_control.hotend2.thermistor EPCOS100K #
  148. ##temperature_control.hotend2.beta 4066 # or set the beta value
  149.  
  150. #temperature_control.hotend2.set_m_code 884 #
  151. #temperature_control.hotend2.set_and_wait_m_code 889 #
  152. #temperature_control.hotend2.designator T1 #
  153.  
  154. #temperature_control.hotend2.p_factor 13.7 # permanently set the PID values after an auto pid
  155. #temperature_control.hotend2.i_factor 0.097 #
  156. #temperature_control.hotend2.d_factor 24 #
  157.  
  158. #temperature_control.hotend2.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
  159.  
  160. temperature_control.bed.enable true #
  161. temperature_control.bed.thermistor_pin 0.25 #
  162. temperature_control.bed.heater_pin 2.5 #
  163. temperature_control.bed.thermistor EPCOS100K # see
  164. #temperature_control.bed.beta 4066 # or set the beta value
  165.  
  166. #temperature_control.bed.set_m_code 140 #
  167. #temperature_control.bed.set_and_wait_m_code 190 #
  168. #temperature_control.bed.designator B #
  169.  
  170. #temperature_control.bed.bang_bang false # set to true to use bang bang control rather than PID
  171. #temperature_control.bed.hysteresis 2.0 # set to the temperature in degrees C to use as hysteresis
  172. # when using bang bang
  173.  
  174. # Switch module for fan control
  175. switch.fan.enable true #
  176. switch.fan.input_on_command M106 #
  177. switch.fan.input_off_command M107 #
  178. switch.fan.output_pin 0.26 # if fan to D9 set 2.7 or fan1 0.26
  179. switch.fan.output_type pwm # pwm output settable with S parameter in the input_on_comand
  180.  
  181. #switch.fan.max_pwm 255 # set max pwm for the pin default is 255
  182.  
  183. #switch.misc.enable true #
  184. #switch.misc.input_on_command M42 #
  185. #switch.misc.input_off_command M43 #
  186. #switch.misc.output_pin 2.4 #
  187. #switch.misc.output_type digital # just an on or off pin
  188.  
  189. # automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
  190. # useful to turn on a fan or water pump to cool the hotend
  191. #temperatureswitch.hotend.enable true #
  192. #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
  193. #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch
  194. #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch
  195. #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
  196. #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
  197.  
  198. # Switch module for spindle control
  199. #switch.spindle.enable false #
  200.  
  201. # Endstops
  202. endstops_enable true # the endstop module is enabled by default and can be disabled here
  203. delta_homing true # forces all three axis to home a the same time regardless of
  204. # what is specified in G28
  205. alpha_min_endstop nc #
  206. alpha_max_endstop 1.24^ # add ! to invert pullup if switch is NO to ground
  207. alpha_homing_direction home_to_max # Home up
  208. alpha_max 0 #
  209. beta_min_endstop nc #
  210. beta_max_endstop 1.26^ #
  211. beta_homing_direction home_to_max #
  212. beta_max 0 #
  213. gamma_min_endstop nc #
  214. gamma_max_endstop 1.28^ #
  215. gamma_homing_direction home_to_max #
  216. gamma_max 237 #
  217.  
  218. alpha_fast_homing_rate_mm_s 200 # homing feedrates in mm/second
  219. beta_fast_homing_rate_mm_s 200 #
  220. gamma_fast_homing_rate_mm_s 200 #
  221. alpha_slow_homing_rate_mm_s 20 #
  222. beta_slow_homing_rate_mm_s 20 #
  223. gamma_slow_homing_rate_mm_s 20
  224.  
  225. alpha_homing_retract_mm 5 # retract/bounce distance after homing in mm
  226. beta_homing_retract_mm 5 #
  227. gamma_homing_retract_mm 5 #
  228.  
  229. alpha_trim -5 # software trim for alpha stepper endstop (in mm)
  230. beta_trim -5 # software trim for beta stepper endstop (in mm)
  231. gamma_trim -5 # software trim for gamma stepper endstop (in mm)
  232.  
  233. #endstop_debounce_count 100 # uncomment if you get noise on your endstops
  234.  
  235. # optional Z probe
  236. zprobe.enable true # set to true to enable a zprobe
  237. zprobe.probe_pin 1.29^ # pin probe is attached to if NC remove the !
  238. zprobe.slow_feedrate 5 # mm/sec probe feed rate
  239. #zprobe.debounce_count 100 # set if noisy
  240. zprobe.fast_feedrate 100 # move feedrate mm/sec
  241. zprobe.probe_height 5 # how much above bed to start probe
  242. #gamma_min_endstop nc # normally 1.28. Change to nc to prevent conflict,
  243.  
  244. # associated with zprobe the leveling strategy to use
  245. #leveling-strategy.delta-calibration.enable true # basic delta calibration
  246. #leveling-strategy.delta-calibration.radius 100 # the probe radius
  247.  
  248. # Pause button
  249. #pause_button_enable true # Pause button enable
  250. #pause_button_pin 2.12 # pause button pin. default is P2.12
  251. #kill_button_enable false # set to true to enable a kill button
  252. #kill_button_pin 2.11 # kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
  253.  
  254. # Panel
  255. panel.enable true # set to true to enable the panel code
  256.  
  257. panel.lcd viki2 # st7565_glcd
  258. panel.spi_channel 0 # spi channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
  259. panel.spi_cs_pin 1.22 # spi chip select ; GLCD EXP1 Pin 4
  260. panel.a0_pin 2.6
  261. panel.encoder_a_pin 4.28!^ # encoder pin ; GLCD EXP2 Pin 3
  262. panel.encoder_b_pin 1.27!^ # encoder pin ; GLCD EXP2 Pin 5
  263.  
  264. panel.click_button_pin 3.26!^
  265. panel.buzz_pin 1.30
  266.  
  267.  
  268.  
  269. #panel.pause_button_pin 1.23!^ # kill/pause ; GLCD EXP2 Pin 8 either
  270.  
  271. panel.reverse 1
  272.  
  273. panel.external_sd true # set to true if there is an extrernal sdcard on the panel
  274. panel.external_sd.spi_channel 0 # set spi channel the sdcard is on
  275. panel.external_sd.spi_cs_pin 0.16 # set spi chip select for the sdcard
  276. panel.external_sd.sdcd_pin 3.25!^ # sd detect signal (set to nc if no sdcard detect)
  277.  
  278.  
  279. #panel.button_pause_pin 2.10!^ # kill/pause ; GLCD EXP2 Pin 8 either
  280. #panel.button_pause_pin 1.23!^ # kill/pause ; GLCD EXP2 Pin 8 either
  281. #panel.back_button_pin 1.23!^ # back button ; GLCD EXP2 Pin 8 or
  282. panel.contrast 19
  283.  
  284. # pins used with other panels
  285. #panel.up_button_pin 0.1! # up button if used
  286. #panel.down_button_pin 0.0! # down button if used
  287. #panel.click_button_pin 1.22! # click button if used
  288.  
  289. panel.menu_offset 0 # some panels will need 1 here
  290. panel.encoder_resolution 4
  291.  
  292. panel.alpha_jog_feedrate 6000 # x jogging feedrate in mm/min
  293. panel.beta_jog_feedrate 6000 # y jogging feedrate in mm/min
  294. panel.gamma_jog_feedrate 6000 # z jogging feedrate in mm/min
  295.  
  296. panel.hotend_temperature 185 # temp to set hotend when preheat is selected
  297. panel.bed_temperature 60 # temp to set bed when preheat is selected
  298.  
  299. # Example of a custom menu entry, which will show up in the Custom entry.
  300. # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
  301. custom_menu.power_on.enable true #
  302. custom_menu.power_on.name Power_on #
  303. custom_menu.power_on.command M80 #
  304.  
  305. custom_menu.power_off.enable true #
  306. custom_menu.power_off.name Power_off #
  307. custom_menu.power_off.command M81 #
  308.  
  309. custom_menu.fan_on.enable true #
  310. custom_menu.fan_on.name Fan_on #
  311. custom_menu.fan_on.command M106 #
  312.  
  313. custom_menu.fan_off.enable true #
  314. custom_menu.fan_off.name Fan_off #
  315. custom_menu.fan_off.command M107 #
  316.  
  317. # Only needed on a smoothieboard
  318. currentcontrol_module_enable false #
  319.  
  320. return_error_on_unhandled_gcode false #
  321.  
  322. # Switch module for servo control
  323. switch.servo.enable true #
  324. switch.servo.input_on_command M280 # M280 S7.5 would be midway
  325. switch.servo.input_off_command M281 # same as M280 S0 0% duty cycle, effectively off
  326. switch.servo.output_pin 1.23 # must be a PWM capable pin
  327. switch.servo.output_type hwpwm # H/W pwm output settable with S parameter in the input_on_comand
  328. #switch.servo.pwm_period_ms 20 # set period to 20ms (50Hz) default is 50Hz
  329.  
  330. custom_menu.servo_on.enable true #
  331. custom_menu.servo_on.name Servo_1 #
  332. custom_menu.servo_on.command M280 S7.5 #
  333.  
  334. custom_menu.servo_off.enable true #
  335. custom_menu.servo_off.name Servo_2 #
  336. custom_menu.servo_off.command M280 S10 #
Advertisement
Add Comment
Please, Sign In to add comment