U-Boot 2016.03 (Sep 02 2016 - 10:48:24 -0700)

CPU:   Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: Nitrogen6_som2
I2C:   ready
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB, total 2 MiB
Display: lvds:mitsubishi (1024x768)
In:    serial
Out:   serial
Err:   serial
Net:   Micrel ksz9021 at 4
FEC, usb_ether
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc1(part 0) is current device
reading /6x_bootscript
2903 bytes read in 13 ms (217.8 KiB/s)
## Executing script at 10008000
Running bootscript 1.0
switch to partitions #0, OK
mmc1(part 0) is current device
reading /imx6q-nitrogen6_som2.dtb
45939 bytes read in 21 ms (2.1 MiB/s)
reading /zImage
5843792 bytes read in 163 ms (34.2 MiB/s)
Kernel image @ 0x10800000 [ 0x000000 - 0x592b50 ]
## Flattened Device Tree blob at 13000000
   Booting using the fdt blob at 0x13000000
   reserving fdt memory region: addr=13000000 size=c000
   Using Device Tree in place at 13000000, end 1300efff

Starting kernel ...

rtc-rv4162 0-0068: rv4162_probe: read error
fsl-hdmi-dai soc:hdmi_audio@00120000: failed to probe. Load HDMI-video first.
imx-audio-hdmi sound-hdmi: initialize HDMI-audio failed. load HDMI-video first!
imx6q-pcie 1ffc000.pcie: phy link never came up
imx6q-pcie 1ffc000.pcie: failed to initialize host
EXT3-fs (mmcblk1p2): error: couldn't mount because of unsupported optional features (240)
EXT2-fs (mmcblk1p2): error: couldn't mount because of unsupported optional features (244)
hid-generic 0003:06D3:6400.0004: device has no listeners, quitting
systemd[1]: alignment.service: Job alignment.service/start deleted to break ordering cycle starting with sysinit.target/start
tsc2004_reset: write_cmd -5
tsc2004 2-0048: Failed to reset TSC -5
ili210x_i2c 2-0041: i2c transfer failed
ili210x_i2c 2-0041: Failed to get firmware version, err: -5
Goodix-TS 2-0014: i2c test failed attempt 1: -5
Goodix-TS 2-0014: i2c test failed attempt 2: -5
tc358743_read_reg:reg=0 ret=-5
tc358743_probe:cannot find camera
Goodix-TS 2-0014: I2C communication failure: -5
egalax_ts 2-0004: Failed to read firmware version
ft5x06-ts 2-0038: Could not detect touch screen -19.
tc358743_probe: failed, error=-19
Goodix-TS 2-005d: i2c test failed attempt 1: -5
Goodix-TS 2-005d: i2c test failed attempt 2: -5
Goodix-TS 2-005d: I2C communication failure: -5
mxc_v4l_open: Mxc Camera no sensor ipu0/csi1
mxc_v4l_open: Mxc Camera no sensor ipu0/csi0
mxc_v4l_open: Mxc Camera no sensor ipu1/csi1
mxc_v4l_open: Mxc Camera no sensor ipu0/csi0
update_device_addr: ov5640_mipi ret=-5
ov5640_read_reg(mipi):reg=300a ret=-5
update_device_addr: ov5642 ret=-5
ov5642_read_reg:write reg error:reg=300a

Automotive Grade Linux 3.0.0+snapshot-20161215 nitrogen6x ttymxc1

nitrogen6x login: root
Last login: Wed Feb 22 15:08:07 UTC 2017 on tty1
root@nitrogen6x:~# cd /usr/AGL/homescreen/
root@nitrogen6x:/usr/AGL/homescreen# ./HomeScreen
Using Wayland-EGL
D-Bus: connect to org.agl.windowmanager /windowmanager
D-Bus: connect to org.agl.homescreen /Popup
D-Bus: connect to org.agl.homescreenappframeworkbindertizen /AppFramework
D-Bus: connect to org.agl.homescreenappframeworkbinder /AppFramework
qml: app is  hvac@0.1
launch "hvac@0.1"
pid: 473
makeMeVisible 473