Seagate GoFlex Satellite dmesg

bility grouping on.  Total pages: 32512
Kernel command line: mem=128M console=ttyS0,115200n8 noinitrd root=/dev/mtdblock7 rw rootfstype=jffs2 mtdparts=omap2-nand.0:512k(X-Loader),512k(U-Boot),128k(Boot-ARGS),256k(Factory-Settings),128k(firmware-detail),3M(kernel-1),3M(kernel-2),60M(jffs2-1),-(jffs2-2)
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125240KB available (3992K code, 311K data, 140K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:368
Clocking rate (Crystal/Core/MPU): 12.0/332/600 MHz
Reprogramming SDRC clock to 332000000 Hz
dpll3_m2_clk rate change failed: -22
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP GPIO hardware version 2.5
OMAP clockevent source: GPTIMER1 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 597.64 BogoMIPS (lpj=2334720)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
mux: Setting signal i2c2_scl.i2c2_scl 0x011f -> 0x0100
mux: Setting signal i2c2_sda.i2c2_sda 0x011f -> 0x0100
mux: Setting signal i2c3_scl.i2c3_scl 0x011f -> 0x0100
mux: Setting signal i2c3_sda.i2c3_sda 0x011f -> 0x0100
mux: Setting signal cam_d5.gpio104 0x010f -> 0x0004
mux: Setting signal etk_d11.hsusb2_stp 0x010c -> 0x0003
mux: Setting signal etk_d10.hsusb2_clk 0x010c -> 0x0003
mux: Setting signal etk_d12.hsusb2_dir 0x010c -> 0x010b
mux: Setting signal etk_d13.hsusb2_nxt 0x010c -> 0x010b
mux: Setting signal etk_d14.hsusb2_data0 0x010c -> 0x010b
mux: Setting signal etk_d15.hsusb2_data1 0x010c -> 0x010b
mux: Setting signal mcspi1_cs3.hsusb2_data2 0x011f -> 0x010b
mux: Setting signal mcspi2_cs1.hsusb2_data3 0x010f -> 0x010b
mux: Setting signal mcspi2_simo.hsusb2_data4 0x010f -> 0x010b
mux: Setting signal mcspi2_somi.hsusb2_data5 0x010f -> 0x010b
mux: Setting signal mcspi2_cs0.hsusb2_data6 0x011f -> 0x010b
mux: Setting signal mcspi2_clk.hsusb2_data7 0x010f -> 0x010b
mux: Setting signal sdmmc1_clk.sdmmc1_clk 0x0018 -> 0x0118
mux: Setting signal sdmmc1_cmd.sdmmc1_cmd 0x0118 -> 0x0118
mux: Setting signal sdmmc1_dat0.sdmmc1_dat0 0x0118 -> 0x0118
mux: Setting signal sdmmc1_dat1.sdmmc1_dat1 0x0118 -> 0x0118
mux: Setting signal sdmmc1_dat2.sdmmc1_dat2 0x0118 -> 0x0118
mux: Setting signal sdmmc1_dat3.sdmmc1_dat3 0x0118 -> 0x0118
mux: Setting signal cam_d0.gpio99 0x010f -> 0x0104
mux: Setting signal cam_d1.gpio100 0x010f -> 0x0104
mux: Setting signal sys_clkreq.gpio1 0x0100 -> 0x011c
mux: Setting signal sys_clkout1.gpio10 0x011c -> 0x0104
mux: Setting signal hdq_sio.gpio170 0x001c -> 0x0004
mux: Setting signal sys_nreswarm.gpio30 0x001c -> 0x0104
mux: Setting signal cam_d4.gpio103 0x000c -> 0x0004
mux: Setting signal cam_d3.gpio102 0x001c -> 0x0004
mux: Setting signal cam_wen.gpio167 0x000c -> 0x0004
DL: Init ZGS GPIO
mux: Setting signal jtag_emu0.gpio11 0x0100 -> 0x0104
mux: Setting signal cam_hs.gpio94 0x000c -> 0x0104
mux: Setting signal cam_d10.gpio109 0x010f -> 0x0104
DL: End Init ZGS GPIO
mux: Setting signal gpmc_ncs4.gpio55 0x0118 -> 0x0004
mux: Setting signal cam_fld.gpio98 0x001c -> 0x0004
mux: Setting signal cam_xclka.gpio96 0x010f -> 0x0004
mux: Setting signal cam_vs.gpio95 0x000c -> 0x0004
mux: Setting signal cam_d2.gpio101 0x010f -> 0x0004
mux: Setting signal cam_pclk.gpio97 0x010f -> 0x0004
mux: Setting signal sys_off_mode.gpio9 0x0100 -> 0x0104
mux: Setting signal sdmmc2_dat2.gpio134 0x0118 -> 0x011c
mux: Setting signal gpmc_ncs3.gpio54 0x0018 -> 0x011c
mux: Setting signal sdmmc2_dat4.gpio136 0x0000 -> 0x011c
omap3evmdc: Driver registration complete
OMAP DMA hardware revision 5.0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c_omap i2c_omap.2: bus 2 rev4.0 at 400 kHz
i2c_omap i2c_omap.3: bus 3 rev4.0 at 400 kHz
i2c_omap i2c_omap.1: bus 1 rev4.0 at 100 kHz
Switching to clocksource 32k_counter
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
->ZGSModule_init
register_chrdev(60,ZGSModule) ret 0
<-ZGSModule_init
AM37x/DM37x  Linux PSP version 03.00.01.06 (OMAP3EVM)
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.13)
msgmni has been set to 244
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 3 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
console [ttyS0] enabled
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
brd: module loaded
loop: module loaded
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xa1 (Micron NAND 128MiB 1,8V 8-bit)
9 cmdlinepart partitions found on MTD device omap2-nand.0
Creating 9 MTD partitions on "omap2-nand.0":
0x000000000000-0x000000080000 : "X-Loader"
0x000000080000-0x000000100000 : "U-Boot"
0x000000100000-0x000000120000 : "Boot-ARGS"
0x000000120000-0x000000160000 : "Factory-Settings"
0x000000160000-0x000000180000 : "firmware-detail"
0x000000180000-0x000000480000 : "kernel-1"
0x000000480000-0x000000780000 : "kernel-2"
0x000000780000-0x000004380000 : "jffs2-1"
0x000004380000-0x000008000000 : "jffs2-2"
OneNAND driver initializing
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver dm9601
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OMAP-EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32 ehci_hcd
usb usb1: SerialNumber: ehci-omap.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
input: satellite_events as /devices/virtual/input/input0
tps65073 1-0048:  tps65073 support ver. 1.1.0 enabled
tps65073_irq_init: read TPS6507x_REG_INT: 0x0
tps65073_irq_init: Activate INT TPS6507x_REG_INT: 0x80
tps65073_init_charging_reg: set TPS6507x_REG_PPATH1: 0xe
PMIC USB or AC power_src=c799930e
PMIC GO-FLEX cable is NOT connected to device power src value=c799930e
 set_charging_hrs : set to 8hrs
OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
cpuidle: using governor ladder
cpuidle: using governor menu
mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
mmc0: clock 0Hz busmode 1 powermode 1 cs 0 Vdd 19 width 0 timing 0
Registered led device: omap3evm::led_Wifi
Registered led device: omap3evm::led_Power
Registered led device: omap3evm::led_Power_dimm
nf_conntrack version 0.5.0 (1959 buckets, 7836 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
lib80211_crypt: registered algorithm 'WEP'
lib80211_crypt: registered algorithm 'CCMP'
lib80211_crypt: registered algorithm 'TKIP'
Power Management for TI OMAP3.
Disabling unused clock "sr2_fck"
Disabling unused clock "sr1_fck"
Disabling unused clock "mcbsp_fck"
Disabling unused clock "mcbsp_fck"
Disabling unused clock "mcbsp_fck"
Disabling unused clock "mcbsp_ick"
Disabling unused clock "mcbsp_ick"
Disabling unused clock "mcbsp_ick"
Disabling unused clock "gpt2_ick"
Disabling unused clock "gpt3_ick"
Disabling unused clock "gpt4_ick"
Disabling unused clock "gpt5_ick"
Disabling unused clock "gpt6_ick"
Disabling unused clock "gpt7_ick"
Disabling unused clock "gpt8_ick"
Disabling unused clock "gpt9_ick"
Disabling unused clock "wdt3_ick"
Disabling unused clock "wdt3_fck"
Disabling unused clock "gpio2_dbck"
Disabling unused clock "gpio3_dbck"
Disabling unused clock "gpio4_dbck"
Disabling unused clock "gpio5_dbck"
Disabling unused clock "gpio6_dbck"
Disabling unused clock "gpt9_fck"
Disabling unused clock "gpt8_fck"
Disabling unused clock "gpt7_fck"
Disabling unused clock "gpt6_fck"
Disabling unused clock "gpt5_fck"
Disabling unused clock "gpt4_fck"
Disabling unused clock "gpt3_fck"
Disabling unused clock "gpt2_fck"
Disabling unused clock "gpt12_ick"
Disabling unused clock "wdt1_ick"
Disabling unused clock "gpio1_dbck"
Disabling unused clock "cam_ick"
Disabling unused clock "cam_mclk"
Disabling unused clock "dss_ick"
Disabling unused clock "dss_96m_fck"
Disabling unused clock "dss1_alwon_fck"
Disabling unused clock "des1_ick"
Disabling unused clock "sha11_ick"
Disabling unused clock "rng_ick"
Disabling unused clock "aes1_ick"
Disabling unused clock "ssi_ick"
Disabling unused clock "mailboxes_ick"
Disabling unused clock "mcbsp_ick"
Disabling unused clock "mcbsp_ick"
Disabling unused clock "gpt10_ick"
Disabling unused clock "gpt11_ick"
Disabling unused clock "mcspi_ick"
Disabling unused clock "mcspi_ick"
Disabling unused clock "mcspi_ick"
Disabling unused clock "mcspi_ick"
Disabling unused clock "hdq_ick"
Disabling unused clock "mspro_ick"
Disabling unused clock "des2_ick"
Disabling unused clock "sha12_ick"
Disabling unused clock "aes2_ick"
Disabling unused clock "icr_ick"
Disabling unused clock "pka_ick"
Disabling unused clock "ssi_ssr_fck"
Disabling unused clock "hdq_fck"
Disabling unused clock "mcspi_fck"
Disabling unused clock "mcspi_fck"
Disabling unused clock "mcspi_fck"
Disabling unused clock "mcspi_fck"
Disabling unused clock "mcbsp_fck"
Disabling unused clock "mcbsp_fck"
Disabling unused clock "mspro_fck"
Disabling unused clock "gpt11_fck"
Disabling unused clock "gpt10_fck"
Disabling unused clock "sad2d_ick"
Disabling unused clock "dpll4_m6x2_ck"
Disabling unused clock "dpll4_m3x2_ck"
Disabling unused clock "dpll3_m3x2_ck"
Disabling unused clock "sys_clkout1"
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 19 width 0 timing 0
mmc0: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd 19 width 0 timing 0
mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 19 width 0 timing 0
mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 14 width 0 timing 0
mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 14 width 0 timing 0
mmc0: queuing unknown CIS tuple 0x80 (50 bytes)
usb 1-2: new high speed USB device using ehci-omap and address 2
mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
usb 1-2: New USB device found, idVendor=13fd, idProduct=0840
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2: Product: External
usb 1-2: Manufacturer: Generic
usb 1-2: SerialNumber: 355645533745585720202020
mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
scsi0 : usb-storage 1-2:1.0
mmc0: queuing unknown CIS tuple 0x02 (1 bytes)
mmc0: clock 26000000Hz busmode 2 powermode 2 cs 0 Vdd 14 width 0 timing 0
mmc0: clock 26000000Hz busmode 2 powermode 2 cs 0 Vdd 14 width 2 timing 0
mmc0: new SDIO card at address 0001
scsi 0:0:0:0: Direct-Access     Generic  External         1.14 PQ: 0 ANSI: 4
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 976773167 512-byte logical blocks: (500 GB/465 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI disk
Empty flash at 0x0309cf98 ends at 0x0309d000
VFS: Mounted root (jffs2 filesystem) on device 31:7.
Freeing init memory: 140K
end_request: I/O error, dev mtdblock0, sector 0
Buffer I/O error on device mtdblock0, logical block 0
end_request: I/O error, dev mtdblock0, sector 8
Buffer I/O error on device mtdblock0, logical block 1
end_request: I/O error, dev mtdblock0, sector 16
Buffer I/O error on device mtdblock0, logical block 2
uncorrectable error :
end_request: I/O error, dev mtdblock0, sector 24
Buffer I/O error on device mtdblock0, logical block 3
end_request: I/O error, dev mtdblock0, sector 0
Buffer I/O error on device mtdblock0, logical block 0
end_request: I/O error, dev mtdblock0, sector 0
Buffer I/O error on device mtdblock0, logical block 0
end_request: I/O error, dev mtdblock0, sector 0
Buffer I/O error on device mtdblock0, logical block 0
end_request: I/O error, dev mtdblock0, sector 8
Buffer I/O error on device mtdblock0, logical block 1
end_request: I/O error, dev mtdblock0, sector 16
Buffer I/O error on device mtdblock0, logical block 2
uncorrectable error :
end_request: I/O error, dev mtdblock0, sector 24
Buffer I/O error on device mtdblock0, logical block 3
end_request: I/O error, dev mtdblock0, sector 0
end_request: I/O error, dev mtdblock0, sector 0
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
ufsd: module license 'Commercial product' taints kernel.
Disabling lock debugging due to kernel taint
ufsd: driver 8.4 (May 19 2011 16:25:25)  LBD=ON with ioctl loaded at bf000000
NTFS read/write support included
Hfs+/HfsX read/write support included
Built for: seagate_satellite_2011-04-28
ufsd: use builtin utf8
ufsd: failed to mount sda
GPIO requested = 9
dhd_customer_oob_irq_map: customer specific Host GPIO number is (9)
#############3GPIO irq mapped = 169
DHD: dongle ram size is set to 294912(orig 294912)
ufsd: use builtin utf8
eth0: Broadcom Dongle Host Driver mac=00:10:75:3b:7a:cc

Dongle Host Driver, version 4.218.248.32
 written as a string:AP_CFG
 written as a string:GoFlex Satellite 55A
 written as a string:open
 written as a string:

 get_parmeter_from_string: No token:COUNTRY= in str:END
Exited wl_control_wl_start
wl0.1: Broadcom Dongle Host Driver mac=00:10:75:3b:7a:cc
dhd_device_event: [wl0.1] Up IP: 0x10019ac
Exited wl_control_wl_start
dhd_device_event: [wl0.1] Down IP: 0x10019ac
dhd_device_event: primary interface is down, AOE clr all
dhd_device_event: [wl0.1] Up IP: 0x10019ac
GoFlex switching handled by Applicaiton
Timer started for 300000 sec.
ufsd: sda1 without journal
Adding 131064k swap on /media/sda1/.swap/swapfile.  Priority:-1 extents:2 across:809124k
dhd_device_event: [eth0] Up IP: 0x7c01a8c0
PMIC USB or AC power_src=4e
PMIC Power Cable connected to device; power src value=4e