Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2012.10.07 22:35:24 =~=~=~=~=~=~=~=~=~=~=~=
- Oct 2 201217:06:24
- FRAC 0x92925552
- memory type is DDR2
- Wait for ddr ready 1power 0x00820616
- Frac 0x92925552
- start change cpu freq
- hbus 0x00000003
- cpu 0x00010001
- start test memory accress
- ddr2 0x40000000
- finish simple test
- U-Boot 2011.09 (Oct 02 2012 - 21:33:21)
- Freescale i.MX28 family
- I2C: ready
- DRAM: 128 MiB
- WARNING: Caches not enabled
- MX28 I2C pads init
- heg_pca955x_init
- MXS I2C: No slave ACK
- MXS I2C read: Failed writing address 27 6
- MXS I2C: No slave ACK
- MXS I2C read: Failed writing address 26 6
- HEG PCA955x v3 detected, PCA953X @ 25
- HEG PCA955x initialized
- MX28 GMPI Init
- MX28 FEC pins init
- NAND: 512 MiB
- MMC: MXS MMC: 0
- In: serial
- Out: serial
- Err: serial
- Net: FEC0
- Hit any key to stop autoboot: 3 2 1 0
- NAND read: device 0 offset 0xa00000, size 0x400000
- 4194304 bytes read: OK
- ## Booting kernel from Legacy Image at 42000000 ...
- Image Name: Linux-2.6.35.3-571-gcca29a0
- Created: 2012-10-07 15:42:52 UTC
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 2343468 Bytes = 2.2 MiB
- Load Address: 40008000
- Entry Point: 40008000
- Verifying Checksum ... OK
- Loading Kernel Image ... OK
- OK
- Starting kernel ...
- Uncompressing Linux... done, booting the kernel.
- Linux version 2.6.35.3-571-gcca29a0 (lars@lars-UX32VD) (gcc version 4.4.4 (4.4.4_09.06.2010) ) #216 PREEMPT Sun Oct 7 17:42:47 CEST 2012
- CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
- CPU: VIVT data cache, VIVT instruction cache
- Machine: Freescale MX28HEG v3 board
- Memory policy: ECC disabled, Data cache writeback
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
- Kernel command line: noinitrd console=ttyAM0,115200 fec_mac=00:04:9F:01:03:ff ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs gpmi
- PID hash table entries: 512 (order: -1, 2048 bytes)
- Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
- Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
- Memory: 128MB = 128MB total
- Memory: 124800k/124800k available, 6272k reserved, 0K highmem
- Virtual kernel memory layout:
- vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- DMA : 0xfde00000 - 0xffe00000 ( 32 MB)
- vmalloc : 0xc8800000 - 0xf0000000 ( 632 MB)
- lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
- modules : 0xbf000000 - 0xc0000000 ( 16 MB)
- .init : 0xc0008000 - 0xc002c000 ( 144 kB)
- .text : 0xc002c000 - 0xc048d000 (4484 kB)
- .data : 0xc048e000 - 0xc04c1120 ( 205 kB)
- SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- Hierarchical RCU implementation.
- RCU-based detection of stalled CPUs is disabled.
- Verbose stalled-CPUs detection is disabled.
- NR_IRQS:352
- Console: colour dummy device 80x30
- console [ttyAM0] enabled
- Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
- pid_max: default: 32768 minimum: 301
- Security Framework initialized
- Mount-cache hash table entries: 512
- CPU: Testing write buffer coherency: ok
- regulator: core version 0.5
- NET: Registered protocol family 16
- regulator: vddd: 800 <--> 1575 mV at 1500 mV fast normal
- HEG: Enabling 1.2V Reg
- regulator: vdddbo: 800 <--> 1575 mV fast normal
- regulator: vdda: 1500 <--> 2275 mV at 1800 mV fast normal
- vddio = 3380000, val=10
- regulator: vddio: 2880 <--> 3680 mV at 3380 mV fast normal
- regulator: overall_current: fast normal
- regulator: vbus5v:
- regulator: mxs-duart-1: fast normal
- regulator: mxs-bl-1: fast normal
- regulator: mxs-i2c-1: fast normal
- regulator: mmc_ssp-1: fast normal
- regulator: mmc_ssp-2: fast normal
- regulator: charger-1: fast normal
- regulator: power-test-1: fast normal
- regulator: cpufreq-1: fast normal
- HEG: Version is 3
- i.MX IRAM pool: 124 KB@0xc8820000
- Initializing GPIO...
- Initializing HEG PINS...
- Pin'AUART0.RX' 0'AUART0.TX' 1'AUART1.RX' 2'AUART1.TX' 3'usb0' 4'usb1' 5'usb0_id' 6'I2C0_SCL' 7'I2C0_SDA' 8'SAIF0_MCLK' 9'SAIF0_LRCLK' 10'SAIF0_BITCLK' 11'SAIF0_SDATA0' 12'SAIF1_SDATA0' 13'SPDIF' 14
- Initializing GPMI pins
- Pin'GPMI D0' 0'GPMI D1' 1'GPMI D2' 2'GPMI D3' 3'GPMI D4' 4'GPMI D5' 5'GPMI D6' 6'GPMI D7' 7'GPMI CE0-' 8'GPMI RDY0' 9'GPMI RDY1' 10'GPMI RD-' 11'GPMI WR-' 12'GPMI ALE' 13'GPMI CLE' 14'GPMI RST-' 15
- Pin'ENET0_MDC' 0'ENET0_MDIO' 1'ENET0_RX_EN' 2'ENET0_RXD0' 3'ENET0_RXD1' 4'ENET0_TX_EN' 5'ENET0_TXD0' 6'ENET0_TXD1' 7'ENET1_RX_EN' 8'ENET1_RXD0' 9'ENET1_RXD1' 10'ENET1_TX_EN' 11'ENET1_TXD0' 12'ENET1_TXD1' 13'ENET_CLK' 14
- Initializing device...
- XXXlpj mx28_init_i2c done
- Initializing HEG device...
- usb DR wakeup device is registered
- IMX usb wakeup probe
- audit: cannot initialize inotify handle
- bio: create slab <bio-0> at 0
- SCSI subsystem initialized
- Freescale USB OTG Driver loaded, $Revision: 1.55 $
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- Advanced Linux Sound Architecture Driver Version 1.0.23.
- Switching to clocksource mxs clock source
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 4096 (order: 3, 32768 bytes)
- TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
- TCP: Hash tables configured (established 4096 bind 4096)
- TCP reno registered
- UDP hash table entries: 256 (order: 0, 4096 bytes)
- UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- NET: Registered protocol family 1
- RPC: Registered udp transport module.
- RPC: Registered tcp transport module.
- RPC: Registered tcp NFSv4.1 backchannel transport module.
- Bus freq driver module loaded
- IMX usb wakeup probe
- usb h1 wakeup device is registered
- pca953x 0-0027: failed reading register
- HEG: PCA955x at 27 missing
- pca953x: probe of 0-0027 failed with error -110
- pca953x 0-0026: failed reading register
- HEG: PCA955x at 26 missing
- pca953x: probe of 0-0026 failed with error -110
- pca953x 0-0025: failed reading register
- HEG: PCA955x at 25 missing
- pca953x: probe of 0-0025 failed with error -110
- mxs_cpu_init: cpufreq init finished
- audit: initializing netlink socket (disabled)
- type=2000 audit(3.650:1): initialized
- VFS: Disk quotas dquot_6.5.2
- Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
- msgmni has been set to 243
- alg: No test for stdrng (krng)
- cryptodev: driver loaded.
- Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
- io scheduler noop registered
- io scheduler deadline registered
- io scheduler cfq registered (default)
- mxs-duart.0: ttyAM0 at MMIO 0x80074000 (irq = 47) is a DebugUART
- mxs-auart.0: ttySP0 at MMIO 0x8006a000 (irq = 112) is a mxs-auart.0
- Found APPUART 3.1.0
- mxs-auart.1: ttySP1 at MMIO 0x8006c000 (irq = 113) is a mxs-auart.1
- Found APPUART 3.1.0
- brd: module loaded
- loop: module loaded
- i.MX GPMI NFC
- NFC: Version 1, 8-chip GPMI and BCH
- Boot ROM: Version 1, Single-chip boot area, block mark swapping supported
- Scanning for NAND Flash chips...
- NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron NAND 512MiB 3,3V 8-bit)
- -----------------------------
- NAND Flash Device Information
- -----------------------------
- Manufacturer : Micron (0x2c)
- Device Code : 0xdc
- Cell Technology : SLC
- Chip Size : 512 MiB
- Pages per Block : 64
- Page Geometry : 2048+64
- ECC Strength : 4 bits
- ECC Size : 512 B
- Data Setup Time : 20 ns
- Data Hold Time : 10 ns
- Address Setup Time: 10 ns
- GPMI Sample Delay : 6 ns
- tREA : Unknown
- tRLOH : Unknown
- tRHOH : Unknown
- Description : MT29F4G08AAA
- -----------------
- Physical Geometry
- -----------------
- Chip Count : 1
- Page Data Size in Bytes: 2048 (0x800)
- Page OOB Size in Bytes : 64
- Block Size in Bytes : 131072 (0x20000)
- Block Size in Pages : 64 (0x40)
- Chip Size in Bytes : 536870912 (0x20000000)
- Chip Size in Pages : 262144 (0x40000)
- Chip Size in Blocks : 4096 (0x1000)
- Medium Size in Bytes : 536870912 (0x20000000)
- ------------
- NFC Geometry
- ------------
- ECC Algorithm : BCH
- ECC Strength : 8
- Page Size in Bytes : 2112
- Metadata Size in Bytes : 10
- ECC Chunk Size in Bytes: 512
- ECC Chunk Count : 4
- Payload Size in Bytes : 2048
- Auxiliary Size in Bytes: 16
- Auxiliary Status Offset: 12
- Block Mark Byte Offset : 1999
- Block Mark Bit Offset : 0
- -----------------
- Boot ROM Geometry
- -----------------
- Boot Area Count : 1
- Boot Area Size in Bytes : 9437184 (0x900000)
- Stride Size in Pages : 64
- Search Area Stride Exponent: 2
- Scanning device for bad blocks
- Boot area protection is enabled.
- Creating 2 MTD partitions on "gpmi-nfc-main":
- 0x000000000000-0x000000900000 : "gpmi-nfc-0-boot"
- 0x000001400000-0x000020000000 : "gpmi-nfc-general-use"
- UBI: attaching mtd1 to ubi0
- UBI: physical eraseblock size: 131072 bytes (128 KiB)
- UBI: logical eraseblock size: 126976 bytes
- UBI: smallest flash I/O unit: 2048
- UBI: VID header offset: 2048 (aligned 2048)
- UBI: data offset: 4096
- UBI: attached mtd1 to ubi0
- UBI: MTD device name: "gpmi-nfc-general-use"
- UBI: MTD device size: 492 MiB
- UBI: number of good PEBs: 3936
- UBI: number of bad PEBs: 0
- UBI: max. allowed volumes: 128
- UBI: wear-leveling threshold: 4096
- UBI: number of internal volumes: 1
- UBI: number of user volumes: 1
- UBI: available PEBs: 0
- UBI: total number of reserved PEBs: 3936
- UBI: number of PEBs reserved for bad PEB handling: 39
- UBI: max/mean erase counter: 4/1
- UBI: image sequence number: 0
- UBI: background thread "ubi_bgt0d" started, PID 947
- ubiblka:
- unknown partition table
- FEC Ethernet Driver
- mx28heg_enet_gpio_init
- fec_enet_mii_bus: probed
- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- fsl-ehci fsl-ehci: Freescale On-Chip EHCI Host Controller
- fsl-ehci fsl-ehci: new USB bus registered, assigned bus number 1
- fsl-ehci fsl-ehci: irq 93, io base 0x80080000
- fsl-ehci fsl-ehci: USB 2.0 started, EHCI 1.00
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
- fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 2
- fsl-ehci fsl-ehci.0: irq 92, io base 0x80090000
- fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 1 port detected
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- ARC USBOTG Device Controller driver (1 August 2005)
- mice: PS/2 mouse device common for all mice
- MXS RTC driver v1.0 hardware v2.3.0
- mxs-rtc mxs-rtc.0: rtc core: registered mxs-rtc as rtc0
- mxs watchdog: initialized, heartbeat 19 sec
- dcp dcp.0: DCP crypto enabled.!
- usbcore: registered new interface driver hiddev
- usbcore: registered new interface driver usbhid
- usbhid: USB HID core driver
- usb 2-1: new high speed USB device using fsl-ehci and address 2
- hub 2-1:1.0: USB hub found
- hub 2-1:1.0: 3 ports detected
- sgtl5000_hw_read: read reg error : Reg 0x00
- Device with ID register 0 is not a SGTL5000
- mxs-spdif mxs-spdif.0: MXS SPDIF Audio Transmitter
- No device for codec mxs spdif
- No device for DAI mxs spdif
- No device for DAI mxs-saif
- No device for DAI mxs-spdif
- asoc: mxs spdif <-> mxs-spdif mapping ok
- ALSA device list:
- #0: mxs-evk (mxs spdif)
- TCP cubic registered
- NET: Registered protocol family 17
- can: controller area network core (rev 20090105 abi 8)
- NET: Registered protocol family 29
- can: raw protocol (rev 20090105)
- mxs-rtc mxs-rtc.0: setting system clock to 1970-01-03 01:02:56 UTC (176576)
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement