Script started on Sun 30 Nov 2014 04:25:19 PM IST
]0;root@Ubuntu: /home/ubunturoot@Ubuntu:/home/ubuntu# exitscript foo.txteen /dev/ttyUSB0 115200
[?1049h[?7h[?1;4;6l[?1h=(B

U-Boot 2011.12 (Apr 18 2012 - 23:08:20)
Seagate GoFlexNet

SoC:   Kirkwood 88F6281_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  3  2  1  0
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt

** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            219 MiB
UBI: number of good PEBs:        1752
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     0
UBI: available PEBs:             1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
3980696 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
** File not found /boot/uInitrd
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-3.15.7-1-ARCH
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3980632 Bytes = 3.8 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.15.7-1-ARCH (nobody@root-armv5-copy) (gcc version 4.8.2 20131219 (prerelease) (GCC) ) #1 PREEMPT Tue Jul 29 19:10:36 MDT 2014
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Seagate GoFlex Net
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 121192K/131072K available (5547K kernel code, 341K rwdata, 1700K rodata, 260K init, 833K bss, 9880K reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc071bf54   (7248 kB)
[    0.000000]       .init : 0xc071c000 - 0xc075d364   ( 261 kB)
[    0.000000]       .data : 0xc075e000 - 0xc07b35dc   ( 342 kB)
[    0.000000]        .bss : 0xc07b35dc - 0xc0883b2c   ( 834 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:114
[    0.000012] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns
[    2.418229] Console: colour dummy device 80x30
[    2.418255] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[    2.508131] pid_max: default: 32768 minimum: 301
[    2.508216] Security Framework initialized
[    2.508243] AppArmor: AppArmor disabled by boot time parameter
[    2.508295] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    2.508313] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    2.508942] Initializing cgroup subsys devices
[    2.508967] Initializing cgroup subsys freezer
[    2.508981] Initializing cgroup subsys net_cls
[    2.508993] Initializing cgroup subsys blkio
[    2.509003] Initializing cgroup subsys bfqio
[    2.509014] Initializing cgroup subsys perf_event
[    2.509028] Initializing cgroup subsys net_prio
[    2.509106] CPU: Testing write buffer coherency: ok
[    2.509491] Setting up static identity map for 0x547018 - 0x547070
[    2.511267] devtmpfs: initialized
[    2.514591] pinctrl core: initialized pinctrl subsystem
[    2.514928] NET: Registered protocol family 16
[    2.515368] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    2.516333] cpuidle: using governor ladder
[    2.516352] cpuidle: using governor menu
[    2.516472] Kirkwood: MV88F6281-A1, TCLK=200000000.
[    2.516493] Feroceon L2: Enabling L2
[    2.516531] Feroceon L2: Cache support initialised.
[    2.526860] vgaarb: loaded
[    2.527183] SCSI subsystem initialized
[    2.527652] usbcore: registered new interface driver usbfs
[    2.527727] usbcore: registered new interface driver hub
[    2.527840] usbcore: registered new device driver usb
[    2.527981] pps_core: LinuxPPS API ver. 1 registered
[    2.527991] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    2.528020] PTP clock support registered
[    2.528932] Switched to clocksource orion_clocksource
[    2.548892] FS-Cache: Loaded
[    2.561830] NET: Registered protocol family 2
[    2.562452] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    2.562477] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    2.562497] TCP: Hash tables configured (established 1024 bind 1024)
[    2.562564] TCP: reno registered
[    2.562578] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    2.562598] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    2.562775] NET: Registered protocol family 1
[    2.564161] futex hash table entries: 256 (order: -1, 3072 bytes)
[    2.564213] audit: initializing netlink subsys (disabled)
[    2.564276] audit: type=2000 audit(0.140:1): initialized
[    2.674195] VFS: Disk quotas dquot_6.5.2
[    2.674472] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.676667] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    2.678463] aufs 3.15-20140728
[    2.678486] msgmni has been set to 236
[    2.680321] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    2.680336] io scheduler noop registered
[    2.680344] io scheduler deadline registered
[    2.680775] io scheduler cfq registered
[    2.680815] io scheduler bfq registered (default)
[    2.680822] BFQ I/O-scheduler version: v7r5
[    2.680990] mv_xor mv_xor.0: Marvell shared XOR driver
[    2.719066] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[    2.759003] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[    2.759205] mv_xor mv_xor.1: Marvell shared XOR driver
[    2.799009] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[    2.839008] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[    2.844505] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    2.845545] console [ttyS0] disabled
[    2.865599] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A
[    3.382641] console [ttyS0] enabled
[    3.395374] brd: module loaded
[    3.403074] loop: module loaded
[    3.406598] sata_mv sata_mv.0: cannot get optional clkdev
[    3.412158] sata_mv sata_mv.0: slots 32 ports 2
[    3.419853] scsi0 : sata_mv
[    3.423391] scsi1 : sata_mv
[    3.426530] ata1: SATA max UDMA/133 irq 21
[    3.430695] ata2: SATA max UDMA/133 irq 21
[    3.435836] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xda
[    3.442445] nand: Toshiba NAND 256MiB 3,3V 8-bit
[    3.447086] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    3.452801] Scanning device for bad blocks
[    3.674935] 4 cmdlinepart partitions found on MTD device orion_nand
[    3.681249] Creating 4 MTD partitions on "orion_nand":
[    3.686410] 0x000000000000-0x000000100000 : "u-boot"
[    3.691864] 0x000000100000-0x000000500000 : "uImage"
[    3.697260] 0x000000500000-0x000002500000 : "rootfs"
[    3.702702] 0x000002500000-0x000010000000 : "data"
[    3.714906] libphy: orion_mdio_bus: probed
[    3.719153] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    3.788966] ata1: SATA link down (SStatus 0 SControl F300)
[    4.158951] ata2: SATA link down (SStatus 0 SControl F300)
[    4.805658] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 02:50:43:1f:bb:82
[    4.814552] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.821129] ehci-pci: EHCI PCI platform driver
[    4.825659] ehci-orion: EHCI orion driver
[    4.829774] orion-ehci orion-ehci.0: EHCI Host Controller
[    4.835219] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[    4.843075] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[    4.868964] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[    4.875850] hub 1-0:1.0: USB hub found
[    4.879682] hub 1-0:1.0: 1 port detected
[    4.884300] usbcore: registered new interface driver usb-storage
[    4.890784] mousedev: PS/2 mouse device common for all mice
[    5.198984] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    5.382043] usb-storage 1-1:1.0: USB Mass Storage device detected
[    5.388453] scsi2 : usb-storage 1-1:1.0
[    5.898963] rtc-mv rtc-mv: internal RTC not ticking
[    5.903987] i2c /dev entries driver
[    5.907994] orion_wdt: Initial timeout 21 sec
[    5.912736] sdhci: Secure Digital Host Controller Interface driver
[    5.918961] sdhci: Copyright(c) Pierre Ossman
[    5.923395] sdhci-pltfm: SDHCI platform and OF driver helper
[    5.930650] ledtrig-cpu: registered to indicate activity on CPUs
[    5.936817] usbcore: registered new interface driver r8712u
[    5.942593] gre: GRE over IPv4 demultiplexor driver
[    5.947501] TCP: cubic registered
[    5.950853] NET: Registered protocol family 17
[    5.955436] Key type dns_resolver registered
[    5.960457] registered taskstats version 1
[    5.965716] console [netcon0] enabled
[    5.969448] netconsole: network logging started
[    5.974064] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    5.981429] Waiting 10 sec before mounting root device...
[    7.283767] scsi 2:0:0:0: Direct-Access                                    PQ: 0 ANSI: 0 CCS
[    7.293542] sd 2:0:0:0: Attached scsi generic sg0 type 0
[    7.299185] sd 2:0:0:0: [sda] 30720000 512-byte logical blocks: (15.7 GB/14.6 GiB)
[    7.307667] sd 2:0:0:0: [sda] Write Protect is off
[    7.313353] sd 2:0:0:0: [sda] No Caching mode page found
[    7.318701] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    7.329922]  sda: sda1
[    7.335606] sd 2:0:0:0: [sda] Attached SCSI removable disk
[   15.993612] EXT2-fs (sda1): warning: mounting ext3 filesystem as ext2
[   16.000172] EXT2-fs (sda1): warning: mounting unchecked fs, running e2fsck is recommended
[   16.009061] VFS: Mounted root (ext2 filesystem) on device 8:1.
[   16.018883] devtmpfs: mounted
[   16.022707] Freeing unused kernel memory: 260K (c071c000 - c075d000)
[   16.043375] Starting init: /sbin/init exists but couldn't execute it (error -13)
[   16.052916] Starting init: /bin/init exists but couldn't execute it (error -13)
[   16.063365] Starting init: /bin/sh exists but couldn't execute it (error -13)
[   16.070585] Kernel panic - not syncing: No working init found.  Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[   16.083773] CPU: 0 PID: 1 Comm: swapper Not tainted 3.15.7-1-ARCH #1
[   16.090178] [<c000ee80>] (unwind_backtrace) from [<c000c41c>] (show_stack+0x10/0x14)
[   16.097964] [<c000c41c>] (show_stack) from [<c0539b20>] (panic+0x8c/0x1ec)
[   16.104886] [<c0539b20>] (panic) from [<c053837c>] (kernel_init+0xc8/0xec)
[   16.111793] [<c053837c>] (kernel_init) from [<c00094f0>] (ret_from_fork+0x14/0x24)
[   16.119396] ---[ end Kernel panic - not syncing: No working init found.  Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.