API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Mar 5th, 2015
252
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 18.77 KB | None | 0 0
raw download clone embed print report
  1. U-Boot SPL 2015.04-rc3-00017-g205b3bf-dirty (Mar 05 2015 - 09:48:05)
  2. SPL: Please implement spl_start_uboot() for your board
  3. SPL: Direct Linux boot not active!
  4.  
  5.  
  6. U-Boot 2015.04-rc3-00017-g205b3bf-dirty (Mar 05 2015 - 09:48:05)
  7.  
  8. OMAP3530-GP ES3.0, CPU-OPP2, L3-165MHz, Max CPU Clock 600 MHz
  9. OMAP3 Beagle board + LPDDR/NAND
  10. I2C: ready
  11. DRAM: 256 MiB
  12. NAND: 256 MiB
  13. MMC: OMAP SD/MMC: 0
  14. Error: Bad compare! failed
  15. Error: Bad compare! failed
  16. NAND read from offset 260000 failed -74
  17. *** Warning - readenv() failed, using default environment
  18.  
  19. Beagle Rev C1/C2/C3
  20. Timed out in wait_for_event: status=0000
  21. Check if pads/pull-ups of bus 1 are properly configured
  22. No EEPROM on expansion board
  23. Die ID #5ac400030000000004013f8901001001
  24. Net: usb_ether
  25. Error: usb_ether address not set.
  26.  
  27. Hit any key to stop autoboot: 0
  28. switch to partitions #0, OK
  29. mmc0 is current device
  30. gpio: pin 173 (gpio 173) value is 1
  31. gpio: pin 7 (gpio 7) value is 0
  32. SD/MMC found on device 0
  33. reading uEnv.txt
  34. 612 bytes read in 4 ms (149.4 KiB/s)
  35. Loaded environment from uEnv.txt
  36. Importing environment from mmc ...
  37. Running uenvcmd ...
  38. starting USB...
  39. USB0: USB EHCI 1.00
  40. scanning bus 0 for devices... 1 USB Device(s) found
  41. scanning usb for storage devices... 0 Storage Device(s) found
  42. scanning usb for ethernet devices... 0 Ethernet Device(s) found
  43. ERROR: Need valid 'usbnet_devaddr' to be set
  44. at ../drivers/usb/gadget/ether.c:2333/usb_eth_init()
  45. ERROR: Need valid 'usbnet_devaddr' to be set
  46. at ../drivers/usb/gadget/ether.c:2333/usb_eth_init()
  47. Wrong Image Format for bootm command
  48. ERROR: can't get kernel image!
  49. reading boot.scr
  50. ** Unable to read file boot.scr **
  51. ** File not found /boot/uImage **
  52. Booting from nand ...
  53.  
  54. NAND read: device 0 offset 0x280000, size 0x400000
  55. Error: Bad compare! failed
  56. Error: Bad compare! failed
  57. Error: Bad compare! failed
  58. Error: Bad compare! failed
  59. Error: Bad compare! failed
  60. Error: Bad compare! failed
  61. Error: Bad compare! failed
  62. Error: Bad compare! failed
  63. Error: Bad compare! failed
  64. Error: Bad compare! failed
  65. Error: Bad compare! failed
  66. Error: Bad compare! failed
  67. Error: Bad compare! failed
  68. Error: Bad compare! failed
  69. Error: Bad compare! failed
  70. Error: Bad compare! failed
  71. Error: Bad compare! failed
  72. Error: Bad compare! failed
  73. Error: Bad compare! failed
  74. Error: Bad compare! failed
  75. Error: Bad compare! failed
  76. Error: Bad compare! failed
  77. Error: Bad compare! failed
  78. Error: Bad compare! failed
  79. Error: Bad compare! failed
  80. Error: Bad compare! failed
  81. Error: Bad compare! failed
  82. Error: Bad compare! failed
  83. Error: Bad compare! failed
  84. Error: Bad compare! failed
  85. Error: Bad compare! failed
  86. Error: Bad compare! failed
  87. Error: Bad compare! failed
  88. Error: Bad compare! failed
  89. NAND read from offset 280000 failed -74
  90. 0 bytes read: ERROR
  91. Wrong Image Format for bootm command
  92. ERROR: can't get kernel image!
  93. 4479120 bytes read in 483 ms (8.8 MiB/s)
  94. 61702 bytes read in 23 ms (2.6 MiB/s)
  95. Booting with DT from mmc0 ...
  96. Kernel image @ 0x80300000 [ 0x000000 - 0x445890 ]
  97. ## Flattened Device Tree blob at 82000000
  98. Booting using the fdt blob at 0x82000000
  99. Using Device Tree in place at 82000000, end 82012105
  100.  
  101. Starting kernel ...
  102.  
  103. [ 0.000000] Booting Linux on physical CPU 0x0
  104. [ 0.000000] Initializing cgroup subsys cpuset
  105. [ 0.000000] Initializing cgroup subsys cpu
  106. [ 0.000000] Initializing cgroup subsys cpuacct
  107. [ 0.000000] Linux version 4.0.0-rc1-dirty (mporter@beef) (gcc version 4.7.4 (Ubuntu/Linaro 4.7.4-2ubuntu1) ) #14 SMP Thu Mar 5 10:12:37 EST 2015
  108. [ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387d
  109. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
  110. [ 0.000000] Machine model: TI OMAP3 BeagleBoard
  111. [ 0.000000] cma: Reserved 16 MiB at 0x8e800000
  112. [ 0.000000] Memory policy: Data cache writeback
  113. [ 0.000000] On node 0 totalpages: 65280
  114. [ 0.000000] free_area_init_node: node 0, pgdat c08edd80, node_mem_map cfcb1000
  115. [ 0.000000] Normal zone: 576 pages used for memmap
  116. [ 0.000000] Normal zone: 0 pages reserved
  117. [ 0.000000] Normal zone: 65280 pages, LIFO batch:15
  118. [ 0.000000] CPU: All CPU(s) started in SVC mode.
  119. [ 0.000000] OMAP3430/3530 ES3.0 (l2cache iva sgx neon isp )
  120. [ 0.000000] XXXX o3_dump_arm_regs:CPUID=0x411fc083 ACR=0x00000042 L2AUXCR=0x00000042n
  121. [ 0.000000] PERCPU: Embedded 12 pages/cpu @cfc3b000 s18496 r8192 d22464 u49152
  122. [ 0.000000] pcpu-alloc: s18496 r8192 d22464 u49152 alloc=12*4096
  123. [ 0.000000] pcpu-alloc: [0] 0
  124. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64704
  125. [ 0.000000] Kernel command line: console=ttyO2,115200n8 debug mpurate=auto buddy=none camera=none vram=12M omapfb.mode=dvi:640x480MR-16@60 omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
  126. [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
  127. [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
  128. [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
  129. [ 0.000000] Memory: 224272K/261120K available (5848K kernel code, 591K rwdata, 2260K rodata, 432K init, 8219K bss, 20464K reserved, 16384K cma-reserved, 0K highmem)
  130. [ 0.000000] Virtual kernel memory layout:
  131. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  132. [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
  133. [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
  134. [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
  135. [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  136. [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  137. [ 0.000000] .text : 0xc0008000 - 0xc07f356c (8110 kB)
  138. [ 0.000000] .init : 0xc07f4000 - 0xc0860000 ( 432 kB)
  139. [ 0.000000] .data : 0xc0860000 - 0xc08f3c28 ( 592 kB)
  140. [ 0.000000] .bss : 0xc08f3c28 - 0xc10fa950 (8220 kB)
  141. [ 0.000000] Hierarchical RCU implementation.
  142. [ 0.000000] Additional per-CPU info printed with stalls.
  143. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
  144. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
  145. [ 0.000000] NR_IRQS:16 nr_irqs:16 16
  146. [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
  147. [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
  148. [ 0.000000] OMAP clockevent source: timer12 at 32768 Hz
  149. [ 0.000030] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns
  150. [ 0.000061] OMAP clocksource: 32k_counter at 32768 Hz
  151. [ 0.001373] Console: colour dummy device 80x30
  152. [ 0.001464] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
  153. [ 0.001464] ... MAX_LOCKDEP_SUBCLASSES: 8
  154. [ 0.001495] ... MAX_LOCK_DEPTH: 48
  155. [ 0.001495] ... MAX_LOCKDEP_KEYS: 8191
  156. [ 0.001525] ... CLASSHASH_SIZE: 4096
  157. [ 0.001525] ... MAX_LOCKDEP_ENTRIES: 32768
  158. [ 0.001556] ... MAX_LOCKDEP_CHAINS: 65536
  159. [ 0.001556] ... CHAINHASH_SIZE: 32768
  160. [ 0.001556] memory used by lock dependency info: 5167 kB
  161. [ 0.001586] per task-struct memory footprint: 1152 bytes
  162. [ 0.001617] Calibrating delay loop... 597.60 BogoMIPS (lpj=2988032)
  163. [ 0.098052] pid_max: default: 32768 minimum: 301
  164. [ 0.098602] Security Framework initialized
  165. [ 0.098846] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  166. [ 0.098876] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  167. [ 0.103485] Initializing cgroup subsys blkio
  168. [ 0.103546] Initializing cgroup subsys memory
  169. [ 0.103698] Initializing cgroup subsys devices
  170. [ 0.103820] Initializing cgroup subsys freezer
  171. [ 0.104034] Initializing cgroup subsys perf_event
  172. [ 0.104156] CPU: Testing write buffer coherency: ok
  173. [ 0.106170] CPU0: thread -1, cpu 0, socket -1, mpidr 0
  174. [ 0.106353] Setting up static identity map for 0x8058aee0 - 0x8058af50
  175. [ 0.112213] Brought up 1 CPUs
  176. [ 0.112243] SMP: Total of 1 processors activated (597.60 BogoMIPS).
  177. [ 0.112274] CPU: All CPU(s) started in SVC mode.
  178. [ 0.116882] devtmpfs: initialized
  179. [ 0.130554] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
  180. [ 0.222808] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp
  181. [ 0.225341] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp
  182. [ 0.308654] omap_hwmod: mcbsp2: _wait_target_ready failed: -16
  183. [ 0.308685] omap_hwmod: mcbsp2: cannot be enabled for reset (3)
  184. [ 0.355865] pinctrl core: initialized pinctrl subsystem
  185. [ 0.472381] NET: Registered protocol family 16
  186. [ 0.484222] DMA: preallocated 256 KiB pool for atomic coherent allocations
  187. [ 0.487609] cpuidle: using governor ladder
  188. [ 0.487670] cpuidle: using governor menu
  189. [ 0.498016] Reprogramming SDRC clock to 332000000 Hz
  190. [ 0.510986] omap_gpio 48310000.gpio: could not find pctldev for node /ocp/pinmux@48002a00/pinmux_gpio1_pins, deferring probe
  191. [ 0.511047] platform 48310000.gpio: Driver omap_gpio requests probe deferral
  192. [ 0.514221] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
  193. [ 0.515747] OMAP GPIO hardware version 2.5
  194. [ 0.517669] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
  195. [ 0.520660] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
  196. [ 0.523803] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
  197. [ 0.526885] gpiochip_add: registered GPIOs 128 to 159 on device: gpio
  198. [ 0.530242] irq: no irq domain found for /ocp/pinmux@48002030 !
  199. [ 0.558349] omap-gpmc 6e000000.gpmc: GPMC revision 5.0
  200. [ 0.570861] No ATAGs?
  201. [ 0.570922] hw-breakpoint: debug architecture 0x4 unsupported.
  202. [ 0.575042] OMAP DMA hardware revision 4.0
  203. [ 0.670104] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver
  204. [ 0.671600] of_get_named_gpiod_flags: parsed 'gpio' property of node '/hsusb2_power_reg[0]' - status (-517)
  205. [ 0.671722] platform hsusb2_power_reg: Driver reg-fixed-voltage requests probe deferral
  206. [ 0.677703] SCSI subsystem initialized
  207. [ 0.678802] libata version 3.00 loaded.
  208. [ 0.680053] usb_phy_generic hsusb2_phy: GPIO lookup for consumer reset
  209. [ 0.680084] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup
  210. [ 0.680236] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb2_phy[0]' - status (0)
  211. [ 0.680389] usb_phy_generic hsusb2_phy: GPIO lookup for consumer vbus-detect
  212. [ 0.680419] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup
  213. [ 0.680450] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpios' property of node '/hsusb2_phy[0]'
  214. [ 0.680480] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpio' property of node '/hsusb2_phy[0]'
  215. [ 0.680480] usb_phy_generic hsusb2_phy: using lookup tables for GPIO lookup
  216. [ 0.680664] usb_phy_generic hsusb2_phy: lookup for GPIO vbus-detect failed
  217. [ 0.681213] platform hsusb2_phy: Driver usb_phy_generic requests probe deferral
  218. [ 0.684875] omap_i2c 48070000.i2c: bus 0 rev3.3 at 2600 kHz
  219. [ 0.686828] omap_i2c 48072000.i2c: bus 1 rev3.3 at 100 kHz
  220. [ 0.688476] omap_i2c 48060000.i2c: bus 2 rev3.3 at 100 kHz
  221. [ 0.695831] Switched to clocksource 32k_counter
  222. [ 0.921936] NET: Registered protocol family 2
  223. [ 0.924865] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
  224. [ 0.925201] TCP bind hash table entries: 2048 (order: 4, 73728 bytes)
  225. [ 0.927215] TCP: Hash tables configured (established 2048 bind 2048)
  226. [ 0.927581] TCP: reno registered
  227. [ 0.927642] UDP hash table entries: 256 (order: 2, 20480 bytes)
  228. [ 0.927978] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
  229. [ 0.929443] NET: Registered protocol family 1
  230. [ 0.932067] RPC: Registered named UNIX socket transport module.
  231. [ 0.932098] RPC: Registered udp transport module.
  232. [ 0.932128] RPC: Registered tcp transport module.
  233. [ 0.932159] RPC: Registered tcp NFSv4.1 backchannel transport module.
  234. [ 0.938171] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available
  235. [ 0.947387] futex hash table entries: 256 (order: 2, 16384 bytes)
  236. [ 0.947814] audit: initializing netlink subsys (disabled)
  237. [ 0.948211] audit: type=2000 audit(0.940:1): initialized
  238. [ 0.955139] VFS: Disk quotas dquot_6.5.2
  239. [ 0.955352] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  240. [ 0.959197] NFS: Registering the id_resolver key type
  241. [ 0.959777] Key type id_resolver registered
  242. [ 0.959808] Key type id_legacy registered
  243. [ 0.960113] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
  244. [ 0.967651] io scheduler noop registered
  245. [ 0.967712] io scheduler deadline registered
  246. [ 0.967803] io scheduler cfq registered (default)
  247. [ 0.971466] pinctrl-single 48002030.pinmux: 284 pins at pa fa002030 size 568
  248. [ 0.972290] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92
  249. [ 0.973602] pinctrl-single 480025d8.pinmux: 18 pins at pa fa0025d8 size 36
  250. [ 0.980377] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
  251. [ 0.990295] omap_uart 4806a000.serial: no wakeirq for uart0
  252. [ 0.990356] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]'
  253. [ 0.991180] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0
  254. [ 0.994079] omap_uart 4806c000.serial: no wakeirq for uart0
  255. [ 0.994140] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]'
  256. [ 0.994537] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1
  257. [ 0.997680] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@49020000[0]'
  258. [ 0.998138] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2
  259. [ 1.980957] console [ttyO2] enabled
  260. [ 2.033447] brd: module loaded
  261. [ 2.067138] loop: module loaded
  262. [ 2.084228] twl 0-0048: PIH (irq 23) chaining IRQs 307..315
  263. [ 2.090667] twl 0-0048: power (irq 312) chaining IRQs 315..322
  264. [ 2.159484] twl4030_gpio twl4030-gpio: gpio (irq 307) chaining IRQs 323..340
  265. [ 2.167541] gpiochip_find_base: found new base at 492
  266. [ 2.173583] gpiochip_add: registered GPIOs 492 to 511 on device: twl4030
  267. [ 2.192230] mtdoops: mtd device (mtddev=name/number) must be supplied
  268. [ 2.217071] mousedev: PS/2 mouse device common for all mice
  269. [ 2.222930] i2c /dev entries driver
  270. [ 2.230621] Driver 'mmcblk' needs updating - please use bus_type methods
  271. [ 2.240112] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd
  272. [ 2.246520] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup
  273. [ 2.253387] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]'
  274. [ 2.263000] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]'
  275. [ 2.272521] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup
  276. [ 2.279602] omap_hsmmc 4809c000.mmc: lookup for GPIO cd failed
  277. [ 2.285766] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp
  278. [ 2.292053] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup
  279. [ 2.298919] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]'
  280. [ 2.308532] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]'
  281. [ 2.318054] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup
  282. [ 2.325073] omap_hsmmc 4809c000.mmc: lookup for GPIO wp failed
  283. [ 2.376892] ledtrig-cpu: registered to indicate activity on CPUs
  284. [ 2.385589] oprofile: using arm/armv7
  285. [ 2.390563] TCP: cubic registered
  286. [ 2.394104] Initializing XFRM netlink socket
  287. [ 2.398956] NET: Registered protocol family 17
  288. [ 2.403717] NET: Registered protocol family 15
  289. [ 2.408966] Key type dns_resolver registered
  290. [ 2.413970] omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu_iva
  291. [ 2.421630] omap2_set_init_voltage: unable to set vdd_mpu_iva
  292. [ 2.427734] omap2_set_init_voltage: unable to find boot up OPP for vdd_core
  293. [ 2.434997] omap2_set_init_voltage: unable to set vdd_core
  294. [ 2.443664] PM: no software I/O chain control; some wakeups may be lost
  295. [ 2.453338] ThumbEE CPU extension supported.
  296. [ 2.457946] Registering SWP/SWPB emulation handler
  297. [ 2.462982] SmartReflex Class3 initialized
  298. [ 2.483825] gpiochip_add: registered GPIOs 160 to 191 on device: gpio
  299. [ 2.493164] of_get_named_gpiod_flags: parsed 'gpio' property of node '/hsusb2_power_reg[0]' - status (0)
  300. [ 2.511260] usb_phy_generic hsusb2_phy: GPIO lookup for consumer reset
  301. [ 2.518249] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup
  302. [ 2.525573] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb2_phy[0]' - status (0)
  303. [ 2.535736] usb_phy_generic hsusb2_phy: GPIO lookup for consumer vbus-detect
  304. [ 2.543121] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup
  305. [ 2.550292] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpios' property of node '/hsusb2_phy[0]'
  306. [ 2.560180] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpio' property of node '/hsusb2_phy[0]'
  307. [ 2.569976] usb_phy_generic hsusb2_phy: using lookup tables for GPIO lookup
  308. [ 2.577331] usb_phy_generic hsusb2_phy: lookup for GPIO vbus-detect failed
  309. [ 2.589141] ../drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
  310. [ 2.596130] sr_init: No PMIC hook to init smartreflex
  311. [ 2.602020] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
  312. [ 2.610595] smartreflex smartreflex.0: omap_sr_probe: smartreflex_mpu_iva: No Voltage table for the corresponding vdd. Cannot create debugfs entries for n-values
  313. [ 2.626434] smartreflex: probe of smartreflex.0 failed with error -61
  314. [ 2.633422] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
  315. [ 2.641845] smartreflex smartreflex.1: omap_sr_probe: smartreflex_core: No Voltage table for the corresponding vdd. Cannot create debugfs entries for n-values
  316. [ 2.657196] smartreflex: probe of smartreflex.1 failed with error -61
  317. [ 2.664123] sr_init: platform driver register failed for SR
  318. [ 2.754760] hsusb2_vbus: disabling
  319. [ 2.760040] VUSB3V1: disabling
  320. [ 2.765869] VDAC: disabling
  321. [ 2.771331] VAUX3: disabling
  322. [ 2.777832] mmc0: host does not support reading read-only switch, assuming write-enable
  323. [ 2.789276] Waiting for root device /dev/mmcblk0p2...
  324. [ 2.795104] mmc0: new high speed SDHC card at address 93d8
  325. [ 2.804901] mmcblk0: mmc0:93d8 SD04G 3.69 GiB
  326. [ 2.816009] mmcblk0: p1 p2
  327. [ 5.314147] kjournald starting. Commit interval 5 seconds
  328. [ 5.320526] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended
  329. [ 5.566711] EXT3-fs (mmcblk0p2): using internal journal
  330. [ 5.577362] EXT3-fs (mmcblk0p2): recovery complete
  331. [ 5.582397] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
  332. [ 5.589874] VFS: Mounted root (ext3 filesystem) on device 179:2.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!