Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- smartctl 5.40 2010-10-16 r3189 [i486-slackware-linux-gnu] (local build)
- Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
- === START OF INFORMATION SECTION ===
- Device Model: ST3000DM001-9YN166
- Serial Number: Z1F1HA4L
- Firmware Version: CC9F
- User Capacity: 3,000,592,982,016 bytes
- Device is: Not in smartctl database [for details use: -P showall]
- ATA Version is: 8
- ATA Standard is: ATA-8-ACS revision 4
- Local Time is: Fri Mar 1 11:50:14 2013 GMT
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x00) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Disabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 584) seconds.
- Offline data collection
- capabilities: (0x73) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- No Offline surface scan supported.
- Self-test supported.
- Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 1) minutes.
- Extended self-test routine
- recommended polling time: ( 255) minutes.
- Conveyance self-test routine
- recommended polling time: ( 2) minutes.
- SCT capabilities: (0x3081) SCT Status supported.
- SMART Attributes Data Structure revision number: 10
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000f 117 100 006 Pre-fail Always - 150057168
- 3 Spin_Up_Time 0x0003 092 092 000 Pre-fail Always - 0
- 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 102
- 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
- 7 Seek_Error_Rate 0x000f 060 060 030 Pre-fail Always - 1083621
- 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 457
- 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
- 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 10
- 183 Runtime_Bad_Block 0x0032 099 099 000 Old_age Always - 1
- 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
- 187 Reported_Uncorrect 0x0032 085 085 000 Old_age Always - 15
- 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
- 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
- 190 Airflow_Temperature_Cel 0x0022 072 068 045 Old_age Always - 28 (Min/Max 20/31)
- 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
- 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 4
- 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 299
- 194 Temperature_Celsius 0x0022 028 040 000 Old_age Always - 28 (0 20 0 0)
- 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
- 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
- 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
- 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 98925981728833
- 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 115444181706025
- 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 88694655637
- SMART Error Log Version: 1
- ATA Error Count: 12 (device log contains only the most recent five errors)
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 12 occurred at disk power-on lifetime: 452 hours (18 days + 20 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 e0 ff ff ff ef 00 16d+11:04:21.861 READ DMA EXT
- ef 10 02 00 00 00 a0 00 16d+11:04:21.860 SET FEATURES [Reserved for Serial ATA]
- 27 00 00 00 00 00 e0 00 16d+11:04:21.860 READ NATIVE MAX ADDRESS EXT
- ec 00 00 00 00 00 a0 00 16d+11:04:21.860 IDENTIFY DEVICE
- ef 03 46 00 00 00 a0 00 16d+11:04:21.860 SET FEATURES [Set transfer mode]
- Error 11 occurred at disk power-on lifetime: 452 hours (18 days + 20 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 e0 ff ff ff ef 00 16d+11:04:18.958 READ DMA EXT
- ef 10 02 00 00 00 a0 00 16d+11:04:18.958 SET FEATURES [Reserved for Serial ATA]
- 27 00 00 00 00 00 e0 00 16d+11:04:18.958 READ NATIVE MAX ADDRESS EXT
- ec 00 00 00 00 00 a0 00 16d+11:04:18.958 IDENTIFY DEVICE
- ef 03 46 00 00 00 a0 00 16d+11:04:18.958 SET FEATURES [Set transfer mode]
- Error 10 occurred at disk power-on lifetime: 452 hours (18 days + 20 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 e0 ff ff ff ef 00 16d+11:04:16.101 READ DMA EXT
- ef 10 02 00 00 00 a0 00 16d+11:04:16.101 SET FEATURES [Reserved for Serial ATA]
- 27 00 00 00 00 00 e0 00 16d+11:04:16.101 READ NATIVE MAX ADDRESS EXT
- ec 00 00 00 00 00 a0 00 16d+11:04:16.100 IDENTIFY DEVICE
- ef 03 46 00 00 00 a0 00 16d+11:04:16.100 SET FEATURES [Set transfer mode]
- Error 9 occurred at disk power-on lifetime: 452 hours (18 days + 20 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 e0 ff ff ff ef 00 16d+11:04:13.226 READ DMA EXT
- ef 10 02 00 00 00 a0 00 16d+11:04:13.225 SET FEATURES [Reserved for Serial ATA]
- 27 00 00 00 00 00 e0 00 16d+11:04:13.225 READ NATIVE MAX ADDRESS EXT
- ec 00 00 00 00 00 a0 00 16d+11:04:13.225 IDENTIFY DEVICE
- ef 03 46 00 00 00 a0 00 16d+11:04:13.225 SET FEATURES [Set transfer mode]
- Error 8 occurred at disk power-on lifetime: 452 hours (18 days + 20 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 e0 ff ff ff ef 00 16d+11:04:10.350 READ DMA EXT
- ef 10 02 00 00 00 a0 00 16d+11:04:10.349 SET FEATURES [Reserved for Serial ATA]
- 27 00 00 00 00 00 e0 00 16d+11:04:10.349 READ NATIVE MAX ADDRESS EXT
- ec 00 00 00 00 00 a0 00 16d+11:04:10.349 IDENTIFY DEVICE
- ef 03 46 00 00 00 a0 00 16d+11:04:10.323 SET FEATURES [Set transfer mode]
- SMART Self-test log structure revision number 1
- No self-tests have been logged. [To run self-tests, use: smartctl -t]
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement