Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- HELO
- CPUI
- L1CI
- DRAM
- ----
- PHYS
- ZQDN
- PHYE
- DINT
- LSYN
- USYN
- MSYN
- LMBE
- PASS
- ----
- ZBSS
- CODE
- DATA
- L12F
- MAIN
- CFE version 2.0.3 for BCM96328 (32bit,SP,BE)
- Build Date: Thu Nov 26 15:09:04 CET 2015 (dani@tool)
- Copyright (C) 2000-2009 Broadcom Corporation.
- HS Serial flash device: name S25FL128, id 0x0118 size 16384KB
- Total Flash size: 16384K with 256 sectors
- ** HELLO **
- Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
- Main Thread: TP0
- Memory Test Passed
- Total Memory: 67108864 bytes (64MB)
- Boot Address: 0xb8000000
- Board IP address : 192.168.1.1:ffffff00
- Host IP address : 192.168.1.100
- Gateway IP address :
- Run from flash/host (f/h) : f
- Default host run file name : vmlinux
- Default host flash file name : bcm963xx_fs_kernel
- Boot delay (0-9 seconds) : 1
- Board Id (0-5) : 96328ang
- Number of MAC Addresses (1-32) : 11
- Base MAC Address : f4:3e:61:c2:4e:dc
- PSI Size (1-64) KBytes : 32
- Enable Backup PSI [0|1] : 0
- System Log Size (0-256) KBytes : 0
- Main Thread Number [0|1] : 0
- Voice Board Configuration (0-11) : LE88276
- *** Press any key to stop auto run (1 seconds) ***
- Auto run second count down: 0
- *** Press any key to stop auto run (1 seconds) ***
- Auto run second count down: 0
- Booting from only image (0xb8010000) ...
- Code Address: 0x80A00000, Entry Address: 0x80a00000
- LZMA: Prossible old LZMA format, trying to decompress..
- Decompression OK!
- Entry at 0x80a00000
- Closing network.
- Disabling Switch ports.
- Flushing Receive Buffers...
- 7 buffers found.
- Closing DMA Channels.
- Starting program at 0x80a00000
- [ 0.000000] Linux version 4.1.11 (dani@tool) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r47603) ) #4 Thu Nov 26 19:50:03 CET 2015
- [ 0.000000] Detected Broadcom 0x6328 CPU revision b0
- [ 0.000000] CPU frequency is 320 MHz
- [ 0.000000] 64MB of RAM installed
- [ 0.000000] board_bcm963xx: Boot address 0xb8000000
- [ 0.000000] board_bcm963xx: CFE version: 1.0.37-106.24
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0002a075 (Broadcom BMIPS4350)
- [ 0.000000] board: board name: 96328ang
- [ 0.000000] MIPS: machine is NuCom R5010UN v2
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Memory: 59652K/65536K available (2974K kernel code, 140K rwdata, 604K rodata, 1264K init, 193K bss, 5884K reserved
- , 0K cma-reserved)
- [ 0.000000] NR_IRQS:256
- [ 0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11945377789 ns
- [ 0.000019] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 13421772796ns
- [ 0.008683] Calibrating delay loop... 319.74 BogoMIPS (lpj=639488)
- [ 0.051004] pid_max: default: 32768 minimum: 301
- [ 0.056427] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.063224] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.078432] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
- [ 0.090162] NET: Registered protocol family 16
- [ 0.331380] registering PCI controller with io_map_base unset
- [ 0.362797] PCI host bridge to bus 0000:00
- [ 0.367050] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff]
- [ 0.374116] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
- [ 0.381099] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
- [ 0.388087] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.396931] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 0.406383] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
- [ 0.413401] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f07fff 64bit]
- [ 0.420934] pci 0000:00:00.0: PCI bridge to [bus 01]
- [ 0.426022] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff]
- [ 0.434671] Switched to clocksource MIPS
- [ 0.442082] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
- [ 0.447961] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
- [ 0.453808] bcma: bus0: Found chip with id 43227, rev 0x01 and package 0x09
- [ 0.461010] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x27, class 0x0)
- [ 0.469828] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1E, class 0x0)
- [ 0.478750] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x14, class 0x0)
- [ 0.502965] bcma: bus0: Bus registered
- [ 0.507477] NET: Registered protocol family 2
- [ 0.514207] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.521493] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.528079] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.535106] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.541209] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.548423] NET: Registered protocol family 1
- [ 0.555450] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.566304] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.572367] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.586103] io scheduler noop registered
- [ 0.590199] io scheduler deadline registered (default)
- [ 0.597518] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36, base_baud = 1562500) is a bcm63xx_uart
- [ 0.607184] console [ttyS0] enabled
- [ 0.607184] console [ttyS0] enabled
- [ 0.614339] bootconsole [early0] disabled
- [ 0.614339] bootconsole [early0] disabled
- [ 0.631988] m25p80 spi1.0: found s25fl128s, expected m25p80
- [ 0.637764] m25p80 spi1.0: s25fl128s (16384 Kbytes)
- [ 0.643181] bcm63xxpart: CFE boot tag found with version 6 and board type 96328ang
- [ 0.651071] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
- [ 0.657709] bcm63xxpart: Partition 1 is kernel offset 10100 and length 13bf64
- [ 0.665045] bcm63xxpart: Partition 2 is rootfs offset 14c064 and length ea3f9c
- [ 0.672473] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000
- [ 0.679727] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000
- [ 0.686984] 5 bcm63xxpart partitions found on MTD device spi1.0
- [ 0.693074] Creating 5 MTD partitions on "spi1.0":
- [ 0.698020] 0x000000000000-0x000000010000 : "CFE"
- [ 0.704748] 0x000000010100-0x00000014c064 : "kernel"
- [ 0.711659] 0x00000014c064-0x000000ff0000 : "rootfs"
- [ 0.718479] mtd: device 2 (rootfs) set to be root filesystem
- [ 0.728207] 1 squashfs-split partitions found on MTD device rootfs
- [ 0.734632] 0x000000390000-0x000000ff0000 : "rootfs_data"
- [ 0.742013] 0x000000ff0000-0x000001000000 : "nvram"
- [ 0.748836] 0x000000010000-0x000000ff0000 : "linux"
- [ 0.791918] b53_common: found switch: BCM63xx, rev 0
- [ 0.797581] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
- [ 0.807619] NET: Registered protocol family 10
- [ 0.819596] NET: Registered protocol family 17
- [ 0.824350] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if
- you need this.
- [ 0.837384] 8021q: 802.1Q VLAN Support v1.8
- [ 0.852615] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- [ 0.876976] Freeing unused kernel memory: 1264K (803b4000 - 804f0000)
- [ 2.733134] init: Console is alive
- [ 2.736985] init: - watchdog -
- [ 4.555866] usbcore: registered new interface driver usbfs
- [ 4.561800] usbcore: registered new interface driver hub
- [ 4.567538] usbcore: registered new device driver usb
- [ 4.587110] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 4.596622] ehci-platform: EHCI generic platform driver
- [ 4.702724] ehci-platform ehci-platform: EHCI Host Controller
- [ 4.708706] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
- [ 4.717238] ehci-platform ehci-platform: irq 50, io mem 0xb0002500
- [ 4.734711] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
- [ 4.744865] hub 1-0:1.0: USB hub found
- [ 4.749369] hub 1-0:1.0: 1 port detected
- [ 4.761075] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 4.770350] ohci-platform: OHCI generic platform driver
- [ 4.775988] ohci-platform ohci-platform: Generic Platform OHCI controller
- [ 4.783050] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
- [ 4.791361] ohci-platform ohci-platform: irq 49, io mem 0xb0002600
- [ 4.856666] hub 2-0:1.0: USB hub found
- [ 4.861159] hub 2-0:1.0: 1 port detected
- [ 4.874907] init: - preinit -
- [ 5.615452] random: procd urandom read with 105 bits of entropy available
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 9.139500] random: nonblocking pool is initialized
- [ 9.178858] jffs2: notice: (248) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 o
- rphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 9.198327] mount_root: switching to jffs2 overlay
- ifconfig: SIOCGIFFLAGS: No such device
- [ 9.248282] procd: - early -
- [ 9.251602] procd: - watchdog -
- [ 10.243553] procd: - ubus -
- [ 11.256970] procd: - init -
- Please press Enter to activate this console.
- [ 12.590794] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 12.623723] Loading modules backported from Linux version master-2015-10-26-0-g28c26cb
- [ 12.631907] Backport generated by backports.git backports-20150903-4-g12cf266
- [ 12.645620] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 12.672738] nf_conntrack version 0.5.0 (951 buckets, 3804 max)
- [ 12.749019] xt_time: kernel timezone is -0000
- [ 12.801178] cfg80211: World regulatory domain updated:
- [ 12.806499] cfg80211: DFS Master region: unset
- [ 12.810953] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- [ 12.821004] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- [ 12.829245] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- [ 12.837480] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
- [ 12.845726] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
- [ 12.855493] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
- [ 12.865256] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
- [ 12.873599] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- [ 12.881830] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
- [ 13.017080] PPP generic driver version 2.4.2
- [ 13.026636] NET: Registered protocol family 24
- [ 13.084898] b43-phy0: Broadcom 43227 WLAN found (core revision 30)
- [ 13.092117] b43-phy0: Found PHY: Analog 9, Type 4 (N), Revision 17
- [ 13.098510] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2057, Revision 14, Version 0
- [ 13.107157] Broadcom 43xx driver loaded [ Features: PNL ]
- [ 18.439030] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
- BusyBox v1.24.1 (2015-11-24 12:42:11 CET) built-in shell (ash)
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- DESIGNATED DRIVER (Bleeding Edge, r47603)
- -----------------------------------------------------
- * 2 oz. Orange Juice Combine all juices in a
- * 2 oz. Pineapple Juice tall glass filled with
- * 2 oz. Grapefruit Juice ice, stir well.
- * 2 oz. Cranberry Juice
- -----------------------------------------------------
- root@OpenWrt:/# [ 26.155025] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
- [ 26.178914] device eth0.1 entered promiscuous mode
- [ 26.183866] device eth0 entered promiscuous mode
- [ 26.204395] br-lan: port 1(eth0.1) entered forwarding state
- [ 26.210206] br-lan: port 1(eth0.1) entered forwarding state
- [ 27.531980] cfg80211: Regulatory domain changed to country: JP
- [ 27.538197] cfg80211: DFS Master region: JP
- [ 27.542418] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- [ 27.552436] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- [ 27.560671] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
- [ 27.568911] cfg80211: (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 2300 mBm), (N/A)
- [ 27.577154] cfg80211: (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 2300 mBm), (N/A)
- [ 27.585402] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
- [ 27.595170] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
- [ 27.604932] cfg80211: (5490000 KHz - 5710000 KHz @ 160000 KHz), (N/A, 2300 mBm), (0 s)
- [ 27.613262] cfg80211: (59000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 1000 mBm), (N/A)
- [ 28.210748] br-lan: port 1(eth0.1) entered forwarding state
- [ 29.738720] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
- [ 29.874100] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 29.909183] device wlan0 entered promiscuous mode
- [ 31.419394] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 31.426288] br-lan: port 2(wlan0) entered forwarding state
- [ 31.432011] br-lan: port 2(wlan0) entered forwarding state
- [ 33.434693] br-lan: port 2(wlan0) entered forwarding state
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement