Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot SPL 2012.07-00134-g81316a9 (Aug 25 2012 - 16:25:08)
- Texas Instruments Revision detection unimplemented
- OMAP SD/MMC: 0
- reading u-boot.img
- reading u-boot.img
- U-Boot 2014.07 (Aug 27 2015 - 18:31:45)
- OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-200MHz, Max CPU Clock 1 Ghz
- OMAP3 Beagle board + LPDDR/NAND
- I2C: ready
- DRAM: 512 MiB
- NAND: 0 MiB
- MMC: OMAP SD/MMC: 0
- *** Warning - readenv() failed, using default environment
- Beagle xM Rev C
- Timed out in wait_for_bb: status=1000
- No EEPROM on expansion board
- Die ID #31a200229ff800000168580219029008
- Net: usb_ether
- Hit any key to stop autoboot: 0
- switch to partitions #0, OK
- mmc0 is current device
- gpio: pin 173 (gpio 173) value is 0
- gpio: pin 4 (gpio 4) value is 0
- SD/MMC found on device 0
- reading uEnv.txt
- 140 bytes read in 3 ms (44.9 KiB/s)
- Loaded environment from uEnv.txt
- Importing environment from mmc ...
- 7519600 bytes read in 503 ms (14.3 MiB/s)
- Booting from mmc ...
- ## Booting kernel from Legacy Image at 80200000 ...
- Image Name: Linux-4.0.5
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 7519536 Bytes = 7.2 MiB
- Load Address: 80008000
- Entry Point: 80008000
- Verifying Checksum ... OK
- Loading Kernel Image ... OK
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0
- [ 0.000000] Initializing cgroup subsys cpuset
- [ 0.000000] Initializing cgroup subsys cpu
- [ 0.000000] Initializing cgroup subsys cpuacct
- [ 0.000000] Linux version 4.0.5 (ralph@aud-srv01) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench5
- [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000] Machine: OMAP3 Beagle Board
- [ 0.000000] cma: Reserved 16 MiB at 0x9e800000
- [ 0.000000] Memory policy: Data cache writeback
- [ 0.000000] CPU: All CPU(s) started in SVC mode.
- [ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
- [ 0.000000] PERCPU: Embedded 12 pages/cpu @dfa55000 s17664 r8192 d23296 u49152
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129664
- [ 0.000000] Kernel command line: console=ttyO2,115200n8 mpurate=auto buddy=none camera=none vram=12M omapfb.mot
- [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000] Memory: 484480K/523264K available (10753K kernel code, 841K rwdata, 3956K rodata, 760K init, 903K )
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
- [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
- [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
- [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- [ 0.000000] .text : 0xc0008000 - 0xc0e659ec (14711 kB)
- [ 0.000000] .init : 0xc0e66000 - 0xc0f24000 ( 760 kB)
- [ 0.000000] .data : 0xc0f24000 - 0xc0ff66d0 ( 842 kB)
- [ 0.000000] .bss : 0xc0ff66d0 - 0xc10d83e4 ( 904 kB)
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
- [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
- [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
- [ 0.000000] NR_IRQS:16 nr_irqs:16 16
- [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
- [ 0.000000] ti_clk_register_clk: can't setup clkdm for basic clk ssi_l4_ick
- [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz
- [ 0.000000] clock: dpll5: dpll5_clk omap3630
- [ 0.000000] OMAP clockevent source: timer12 at 32768 Hz
- [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns
- [ 0.000030] OMAP clocksource: 32k_counter at 32768 Hz
- [ 0.000488] Console: colour dummy device 80x30
- [ 0.000549] Calibrating delay loop... 506.26 BogoMIPS (lpj=2531328)
- [ 0.042358] pid_max: default: 32768 minimum: 301
- [ 0.042541] Security Framework initialized
- [ 0.042602] AppArmor: AppArmor disabled by boot time parameter
- [ 0.042633] Yama: becoming mindful.
- [ 0.042907] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.042938] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.044067] Initializing cgroup subsys blkio
- [ 0.044097] Initializing cgroup subsys memory
- [ 0.044189] Initializing cgroup subsys devices
- [ 0.044189] Initializing cgroup subsys freezer
- [ 0.044219] Initializing cgroup subsys net_cls
- [ 0.044250] Initializing cgroup subsys perf_event
- [ 0.044281] Initializing cgroup subsys net_prio
- [ 0.044372] CPU: Testing write buffer coherency: ok
- [ 0.044433] ftrace: allocating 35301 entries in 104 pages
- [ 0.179962] missing device node for CPU 0
- [ 0.179992] CPU0: thread -1, cpu 0, socket -1, mpidr 0
- [ 0.180114] Setting up static identity map for 0x809bd7f0 - 0x809bd848
- [ 0.185821] Brought up 1 CPUs
- [ 0.185852] SMP: Total of 1 processors activated (506.26 BogoMIPS).
- [ 0.185852] CPU: All CPU(s) started in SVC mode.
- [ 0.186981] devtmpfs: initialized
- [ 0.191833] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
- [ 0.250854] xor: measuring software checksum speed
- [ 0.331756] arm4regs : 640.000 MB/sec
- [ 0.417572] 8regs : 552.000 MB/sec
- [ 0.503356] 32regs : 444.800 MB/sec
- [ 0.589141] neon : 923.600 MB/sec
- [ 0.589141] xor: using function: neon (923.600 MB/sec)
- [ 0.589263] pinctrl core: initialized pinctrl subsystem
- [ 0.590911] NET: Registered protocol family 16
- [ 0.594482] DMA: preallocated 256 KiB pool for atomic coherent allocations
- [ 0.597869] OMAP GPIO hardware version 2.5
- [ 0.602264] omap-gpmc omap-gpmc: GPMC revision 5.0
- [ 0.603057] omap_mux_init: Add partition: #1: core, flags: 4
- [ 0.604217] OMAP3 Beagle Rev: xM C
- [ 0.609497] omap_mux_get_by_name: Could not find signal uart4_rx.uart4_rx
- [ 0.615783] Reprogramming SDRC clock to 400000000 Hz
- [ 0.618041] hw-breakpoint: debug architecture 0x4 unsupported.
- [ 0.625274] OMAP DMA hardware revision 5.0
- [ 0.786346] raid6: int32x1 107 MB/s
- [ 0.932434] raid6: int32x2 137 MB/s
- [ 1.078094] raid6: int32x4 159 MB/s
- [ 1.224029] raid6: int32x8 145 MB/s
- [ 1.369750] raid6: neonx1 489 MB/s
- [ 1.515716] raid6: neonx2 751 MB/s
- [ 1.661621] raid6: neonx4 875 MB/s
- [ 1.807525] raid6: neonx8 536 MB/s
- [ 1.807525] raid6: using algorithm neonx4 (875 MB/s)
- [ 1.807556] raid6: using intx1 recovery algorithm
- [ 1.830841] omap-dma-engine omap-dma-engine: OMAP DMA engine driver
- [ 1.833770] SCSI subsystem initialized
- [ 1.834716] usbcore: registered new interface driver usbfs
- [ 1.834838] usbcore: registered new interface driver hub
- [ 1.834991] usbcore: registered new device driver usb
- [ 1.837097] omap_i2c omap_i2c.1: bus 1 rev4.4 at 2600 kHz
- [ 1.837982] omap_i2c omap_i2c.3: bus 3 rev4.4 at 100 kHz
- [ 1.838195] media: Linux media interface: v0.10
- [ 1.838317] Linux video capture interface: v2.00
- [ 1.838470] pps_core: LinuxPPS API ver. 1 registered
- [ 1.838470] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 1.838531] PTP clock support registered
- [ 1.839324] omap-mailbox omap-mailbox: omap mailbox rev 0x40
- [ 1.840026] Advanced Linux Sound Architecture Driver Initialized.
- [ 1.841094] NetLabel: Initializing
- [ 1.841125] NetLabel: domain hash size = 128
- [ 1.841125] NetLabel: protocols = UNLABELED CIPSOv4
- [ 1.841217] NetLabel: unlabeled traffic allowed by default
- [ 1.842315] Switched to clocksource 32k_counter
- [ 1.968963] NET: Registered protocol family 2
- [ 1.970153] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
- [ 1.970214] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
- [ 1.970336] TCP: Hash tables configured (established 4096 bind 4096)
- [ 1.970397] TCP: reno registered
- [ 1.970428] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 1.970458] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 1.970764] NET: Registered protocol family 1
- [ 1.971466] RPC: Registered named UNIX socket transport module.
- [ 1.971466] RPC: Registered udp transport module.
- [ 1.971496] RPC: Registered tcp transport module.
- [ 1.971496] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 1.973693] CPU PMU: probing PMU on CPU 0
- [ 1.973724] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available
- [ 1.977661] futex hash table entries: 256 (order: 2, 16384 bytes)
- [ 1.977813] audit: initializing netlink subsys (disabled)
- [ 1.977905] audit: type=2000 audit(2.190:1): initialized
- [ 1.979736] zpool: loaded
- [ 1.979766] zbud: loaded
- [ 1.980255] VFS: Disk quotas dquot_6.5.2
- [ 1.980377] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 1.981323] NFS: Registering the id_resolver key type
- [ 1.981414] Key type id_resolver registered
- [ 1.981414] Key type id_legacy registered
- [ 1.981445] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
- [ 1.981903] fuse init (API version 7.23)
- [ 1.982299] SGI XFS with ACLs, security attributes, realtime, no debug enabled
- [ 1.985260] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
- [ 1.985534] io scheduler noop registered
- [ 1.985565] io scheduler deadline registered
- [ 1.985626] io scheduler cfq registered (default)
- [ 1.987762] ------------[ cut here ]------------
- [ 1.987823] WARNING: CPU: 0 PID: 1 at drivers/video/fbdev/omap2/dss/dss.c:568 dss_set_fck_rate+0xa0/0xc8()
- [ 1.988494] ---[ end trace 71735f4bac2a4df4 ]---
- [ 1.988586] omapdss_dss omapdss_dss: probe deferral not supported
- [ 1.988769] omapdss CORE error: Failed to initialize DSS platform driver
- [ 1.991149] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
- [ 1.994934] omap_uart omap_uart.0: no wakeirq for uart0
- [ 1.995117] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0
- [ 1.995758] omap_uart omap_uart.1: no wakeirq for uart0
- [ 1.995941] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1
- [ 1.996520] omap_uart omap_uart.2: no wakeirq for uart0
- [ 1.996551] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2
- [ 2.890441] console [ttyO2] enabled
- [ 2.894927] omap_uart omap_uart.3: no wakeirq for uart0
- [ 2.900573] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 96, base_baud = 3000000) is a OMAP UART3
- [ 2.911315] [drm] Initialized drm 1.1.0 20060810
- [ 2.916442] usbcore: registered new interface driver udl
- [ 2.922027] Error: Driver 'tfp410' is already registered, aborting...
- [ 2.947540] twl 1-0048: PIH (irq 23) chaining IRQs 338..346
- [ 2.953521] twl 1-0048: power (irq 343) chaining IRQs 346..353
- [ 2.961181] twl4030_gpio twl4030_gpio: gpio (irq 338) chaining IRQs 354..371
- [ 2.970489] tfp410 tfp410.0: Failed to find video source
- [ 2.976409] connector-dvi connector-dvi.0: Failed to find video source
- [ 2.983245] platform connector-dvi.0: Driver connector-dvi requests probe deferral
- [ 2.991943] platform usb_phy_generic.2: Driver usb_phy_generic requests probe deferral
- [ 3.005493] platform twl4030_usb: Driver twl4030_usb requests probe deferral
- [ 3.021087] usbcore: registered new interface driver dln2
- [ 3.031951] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 3.038970] ehci-platform: EHCI generic platform driver
- [ 3.044647] ehci-omap: OMAP-EHCI Host Controller driver
- [ 3.050262] ehci-omap ehci-omap.0: Can't get PHY device for port 1: -517
- [ 3.057342] platform ehci-omap.0: Driver ehci-omap requests probe deferral
- [ 3.064758] usbcore: registered new interface driver usb-storage
- [ 3.071228] usbcore: registered new interface driver usbserial
- [ 3.077453] usbcore: registered new interface driver usbserial_generic
- [ 3.084350] usbserial: USB Serial support registered for generic
- [ 3.091308] HS USB OTG: no transceiver configured
- [ 3.096282] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
- [ 3.104400] platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral
- [ 3.114440] mousedev: PS/2 mouse device common for all mice
- [ 3.122589] input: twl4030_pwrbutton as /devices/platform/omap_i2c.1/i2c-1/1-004b/twl4030_pwrbutton/input/inpu0
- [ 3.135528] twl_rtc twl_rtc: Power up reset detected.
- [ 3.140960] twl_rtc twl_rtc: Enabling TWL-RTC
- [ 3.148620] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
- [ 3.158142] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
- [ 3.166656] Driver 'mmcblk' needs updating - please use bus_type methods
- [ 3.173767] sdhci: Secure Digital Host Controller Interface driver
- [ 3.180206] sdhci: Copyright(c) Pierre Ossman
- [ 3.553558] sdhci-pltfm: SDHCI platform and OF driver helper
- [ 3.560394] ledtrig-cpu: registered to indicate activity on CPUs
- [ 3.567199] hidraw: raw HID events driver (C) Jiri Kosina
- [ 3.577239] usbcore: registered new interface driver usbhid
- [ 3.583129] usbhid: USB HID core driver
- [ 3.587493] ashmem: initialized
- [ 3.671630] omap-twl4030 omap-twl4030: twl4030-hifi <-> omap-mcbsp.2 mapping ok
- [ 3.684448] oprofile: using arm/armv7
- [ 3.688659] TCP: cubic registered
- [ 3.692291] NET: Registered protocol family 10
- [ 3.698394] mip6: Mobile IPv6
- [ 3.701507] NET: Registered protocol family 17
- [ 3.706481] Key type dns_resolver registered
- [ 3.710998] mpls_gso: MPLS GSO support
- [ 3.721466] ThumbEE CPU extension supported.
- [ 3.726104] Registering SWP/SWPB emulation handler
- [ 3.731231] SmartReflex Class3 initialized
- [ 3.735595] mmc0: host does not support reading read-only switch, assuming write-enable
- [ 3.745239] registered taskstats version 1
- [ 3.750976] Btrfs loaded
- [ 3.754486] mmc0: new high speed SDHC card at address 1234
- [ 3.760864] platform omapdrm.0: Driver omapdrm requests probe deferral
- [ 3.768096] mmcblk0: mmc0:1234 SA08G 7.28 GiB
- [ 3.774414] connector-dvi connector-dvi.0: Failed to find video source
- [ 3.781433] mmcblk0: p1 p2
- [ 3.785949] platform connector-dvi.0: Driver connector-dvi requests probe deferral
- [ 3.794555] platform twl4030_usb: Driver twl4030_usb requests probe deferral
- [ 3.900482] ehci-omap ehci-omap.0: EHCI Host Controller
- [ 3.906463] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
- [ 3.914733] ehci-omap ehci-omap.0: irq 93, io mem 0x48064800
- [ 3.932586] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
- [ 3.938995] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- [ 3.946105] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 3.953674] usb usb1: Product: EHCI Host Controller
- [ 3.958740] usb usb1: Manufacturer: Linux 4.0.5 ehci_hcd
- [ 3.964324] usb usb1: SerialNumber: ehci-omap.0
- [ 3.970184] hub 1-0:1.0: USB hub found
- [ 3.974243] hub 1-0:1.0: 3 ports detected
- [ 3.979797] HS USB OTG: no transceiver configured
- [ 3.984802] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
- [ 3.992980] platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral
- [ 4.000915] platform omapdrm.0: Driver omapdrm requests probe deferral
- [ 4.007904] connector-dvi connector-dvi.0: Failed to find video source
- [ 4.014801] platform connector-dvi.0: Driver connector-dvi requests probe deferral
- [ 4.022918] platform twl4030_usb: Driver twl4030_usb requests probe deferral
- [ 4.031707] input: gpio-keys as /devices/platform/gpio-keys/input/input1
- [ 4.039215] HS USB OTG: no transceiver configured
- [ 4.044189] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
- [ 4.052764] platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral
- [ 4.060943] platform omapdrm.0: Driver omapdrm requests probe deferral
- [ 4.067901] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
- [ 4.077850] connector-dvi connector-dvi.0: Failed to find video source
- [ 4.084716] sr_init: No PMIC hook to init smartreflex
- [ 4.090301] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
- [ 4.098480] platform connector-dvi.0: Driver connector-dvi requests probe deferral
- [ 4.106658] platform twl4030_usb: Driver twl4030_usb requests probe deferral
- [ 4.114501] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
- [ 4.123046] HS USB OTG: no transceiver configured
- [ 4.127960] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
- [ 4.152557] platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral
- [ 4.160644] platform omapdrm.0: Driver omapdrm requests probe deferral
- [ 4.169647] platform omapdss_dss: omap_device_late_idle: enabled but no driver. Idling
- [ 4.178222] ------------[ cut here ]------------
- [ 4.183074] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_device.c:942 __omap_device_late_init+0x60/0x68()
- [ 4.193969] ---[ end trace 71735f4bac2a4df6 ]---
- [ 4.198974] connector-dvi connector-dvi.0: Failed to find video source
- [ 4.205871] platform connector-dvi.0: Driver connector-dvi requests probe deferral
- [ 4.214080] platform twl4030_usb: Driver twl4030_usb requests probe deferral
- [ 4.221771] HS USB OTG: no transceiver configured
- [ 4.226776] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
- [ 4.235198] VDVI: incomplete constraints, leaving on
- [ 4.240417] platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral
- [ 4.248291] VDAC: incomplete constraints, leaving on
- [ 4.253845] VUSB3V1: incomplete constraints, leaving on
- [ 4.260467] ALSA device list:
- [ 4.263610] #0: omap3beagle
- [ 4.303436] EXT4-fs (mmcblk0p2): recovery complete
- [ 4.308441] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
- [ 4.317108] VFS: Mounted root (ext4 filesystem) on device 179:2.
- [ 4.326049] devtmpfs: mounted
- [ 4.330444] Freeing unused kernel memory: 760K (c0e66000 - c0f24000)
- [ 4.380310] request_module: runaway loop modprobe binfmt-0000
- [ 4.395080] Starting init: /sbin/init exists but couldn't execute it (error -8)
- [ 4.444519] request_module: runaway loop modprobe binfmt-0000
- [ 4.458984] Starting init: /bin/sh exists but couldn't execute it (error -8)
- [ 4.466522] Kernel panic - not syncing: No working init found. Try passing init= option to kernel. See Linux .
- [ 4.480194] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 4.0.5 #13
- [ 4.487640] Hardware name: OMAP3 Beagle Board
- [ 4.492218] [<c00188bc>] (unwind_backtrace) from [<c0013bb4>] (show_stack+0x20/0x24)
- [ 4.500305] [<c0013bb4>] (show_stack) from [<c09b5028>] (dump_stack+0x8c/0x9c)
- [ 4.507843] [<c09b5028>] (dump_stack) from [<c09afa2c>] (panic+0xb0/0x230)
- [ 4.515014] [<c09afa2c>] (panic) from [<c09ade28>] (cpu_die+0x0/0x98)
- [ 4.521728] [<c09ade28>] (cpu_die) from [<c000fb68>] (ret_from_fork+0x14/0x2c)
- [ 4.529266] ---[ end Kernel panic - not syncing: No working init found. Try passing init= option to kernel. S.
- [ 28.222381] random: nonblocking pool is initialized
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement