Advertisement
Guest User

Kernel Yocto (3.10.17)

a guest
May 4th, 2015
73
0
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 15.30 KB | None | 0 0
  1. U-Boot 2013.07-00787-g36ed10c (Mar 24 2015 - 16:02:12)
  2.  
  3. CPU: Freescale i.MX6DL rev1.1 at 792 MHz
  4. Reset cause: POR
  5. Board: Ka-Ro TX6U-8010
  6. I2C: ready
  7. DRAM: 1 GiB
  8. VDDCORE set to 1421mV
  9. VDDSOC set to 1421mV
  10. NAND: 128 MiB
  11. MMC: FSL_SDHC: 0, FSL_SDHC: 1
  12. IPU HW Rev: 4
  13. Temperature: 53 C, calibration data 0x5814fa69
  14. CPU clock set to 792.000 MHz
  15. Baseboard: stk5-v3
  16. MAC addr from fuse: 00:0c:c6:7a:39:63
  17. Net: FEC
  18. Hit any key to stop autoboot: 0
  19.  
  20. Loading from nand0, offset 0x180000
  21. Image Name: Linux-3.10.17-1.0.2_ga+g33597e3
  22. Image Type: ARM Linux Kernel Image (uncompressed)
  23. Data Size: 5287648 Bytes = 5 MiB
  24. Load Address: 10008000
  25. Entry Point: 10008000
  26. ## Booting kernel from Legacy Image at 18000000 ...
  27. Image Name: Linux-3.10.17-1.0.2_ga+g33597e3
  28. Image Type: ARM Linux Kernel Image (uncompressed)
  29. Data Size: 5287648 Bytes = 5 MiB
  30. Load Address: 10008000
  31. Entry Point: 10008000
  32. Verifying Checksum ... OK
  33. ## Flattened Device Tree blob at 11000000
  34. Booting using the fdt blob at 0x11000000
  35. Loading Kernel Image ... OK
  36. Loading Device Tree to 4ef3d000, end 4ef4996d ... OK
  37.  
  38. Starting kernel ...
  39.  
  40. Disabling LCD
  41. Booting Linux on physical CPU 0x0
  42. Linux version 3.10.17-1.0.2_ga+g33597e3 (isaac@ubuntu) (gcc version 4.9.1 (GCC) ) #2 SMP PREEMPT Wed Apr 29 19:58:42 IRDT 2015
  43. CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
  44. CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  45. Machine: Freescale i.MX6 Quad/DualLite (Device Tree), model: Ka-Ro electronics TX6U-801x/-803x Module
  46. cma: CMA: reserved 320 MiB at 3a000000
  47. Memory policy: ECC disabled, Data cache writealloc
  48. On node 0 totalpages: 262144
  49. free_area_init_node: node 0, pgdat 80c97680, node_mem_map 80d02000
  50. DMA zone: 2048 pages used for memmap
  51. DMA zone: 0 pages reserved
  52. DMA zone: 262144 pages, LIFO batch:31
  53. PERCPU: Embedded 8 pages/cpu @81517000 s8896 r8192 d15680 u32768
  54. pcpu-alloc: s8896 r8192 d15680 u32768 alloc=8*4096
  55. pcpu-alloc: [0] 0 [0] 1
  56. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
  57. Kernel command line: init=/linuxrc console=ttymxc0,115200 ro debug panic=1 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rootwait rw mtdparts=gpmi-nand:1m@128k(u-boot),384k(env),7m(linux),121728k(rootfs),128k(dtb),512k(bbt)ro rootflags=sync
  58. PID hash table entries: 4096 (order: 2, 16384 bytes)
  59. Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  60. Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  61. Memory: 1024MB = 1024MB total
  62. Memory: 697748k/697748k available, 350828k reserved, 0K highmem
  63. Virtual kernel memory layout:
  64. vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  65. fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  66. vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
  67. lowmem : 0x80000000 - 0xc0000000 (1024 MB)
  68. pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
  69. modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
  70. .text : 0x80008000 - 0x80c022d4 (12265 kB)
  71. .init : 0x80c03000 - 0x80c462c0 ( 269 kB)
  72. .data : 0x80c48000 - 0x80c98be0 ( 323 kB)
  73. .bss : 0x80c98be0 - 0x80d01d64 ( 421 kB)
  74. SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  75. Preemptible hierarchical RCU implementation.
  76. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
  77. NR_IRQS:16 nr_irqs:16 16
  78. L310 cache controller enabled
  79. l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x32050000, Cache size: 524288 B
  80. sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
  81. CPU identified as i.MX6DL, silicon rev 1.1
  82. Console: colour dummy device 80x30
  83. Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
  84. pid_max: default: 32768 minimum: 301
  85. Mount-cache hash table entries: 512
  86. CPU: Testing write buffer coherency: ok
  87. CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
  88. Setting up static identity map for 0x80631048 - 0x806310a0
  89. CPU1: Booted secondary processor
  90. CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
  91. Brought up 2 CPUs
  92. SMP: Total of 2 processors activated (3162.11 BogoMIPS).
  93. CPU: All CPU(s) started in SVC mode.
  94. devtmpfs: initialized
  95. pinctrl core: initialized pinctrl subsystem
  96. regulator-dummy: no parameters
  97. NET: Registered protocol family 16
  98. DMA: preallocated 256 KiB pool for atomic coherent allocations
  99. Use WDOG1 as reset source
  100. syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
  101. vdd1p1: 800 <--> 1375 mV at 1125 mV
  102. vdd3p0: 2800 <--> 3150 mV at 3000 mV
  103. vdd2p5: 2000 <--> 2750 mV at 2425 mV
  104. vddarm: 725 <--> 1450 mV at 1150 mV
  105. vddpu: 725 <--> 1450 mV at 1250 mV
  106. vddsoc: 725 <--> 1450 mV at 1200 mV
  107. syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered
  108. syscon 21bc000.ocotp: regmap [mem 0x021bc000-0x021bffff] registered
  109. hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
  110. hw-breakpoint: maximum watchpoint size is 4 bytes.
  111. imx6dl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
  112. bio: create slab <bio-0> at 0
  113. mxs-dma 110000.dma-apbh: initialized
  114. 3V3_ETN: 3300 mV
  115. 2V5: 2500 mV
  116. 3V3: 3300 mV
  117. LCD0 POWER: 3300 mV
  118. LCD1 POWER: 3300 mV
  119. usbh1_vbus: 5000 mV
  120. i2c-core: driver [max17135] using legacy suspend method
  121. i2c-core: driver [max17135] using legacy resume method
  122. SCSI subsystem initialized
  123. libata version 3.00 loaded.
  124. usbcore: registered new interface driver usbfs
  125. usbcore: registered new interface driver hub
  126. usbcore: registered new device driver usb
  127. i2c i2c-0: IMX I2C adapter registered
  128. i2c i2c-2: IMX I2C adapter registered
  129. Linux video capture interface: v2.00
  130. pps_core: LinuxPPS API ver. 1 registered
  131. pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  132. PTP clock support registered
  133. imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  134. MIPI CSI2 driver module loaded
  135. Advanced Linux Sound Architecture Driver Initialized.
  136. cfg80211: Calling CRDA to update world regulatory domain
  137. Switching to clocksource mxc_timer1
  138. NET: Registered protocol family 2
  139. TCP established hash table entries: 8192 (order: 4, 65536 bytes)
  140. TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
  141. TCP: Hash tables configured (established 8192 bind 8192)
  142. TCP: reno registered
  143. UDP hash table entries: 512 (order: 2, 16384 bytes)
  144. UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  145. NET: Registered protocol family 1
  146. RPC: Registered named UNIX socket transport module.
  147. RPC: Registered udp transport module.
  148. RPC: Registered tcp transport module.
  149. RPC: Registered tcp NFSv4.1 backchannel transport module.
  150. hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
  151. imx-gpc 20dc000.gpc: pu regulator not ready.
  152. failed to find imx6q-mmdc device tree data!
  153. imx6_busfreq busfreq.10: Busfreq init of MMDC failed
  154. imx6_busfreq: probe of busfreq.10 failed with error -22
  155. Bus freq driver module loaded
  156. VFS: Disk quotas dquot_6.5.2
  157. Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  158. NFS: Registering the id_resolver key type
  159. Key type id_resolver registered
  160. Key type id_legacy registered
  161. jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
  162. fuse init (API version 7.22)
  163. msgmni has been set to 2002
  164. io scheduler noop registered
  165. io scheduler deadline registered
  166. io scheduler cfq registered (default)
  167. imx-weim 21b8000.weim: WEIM driver registered.
  168. pwm-backlight backlight.17: unable to request PWM, trying legacy API
  169. MIPI DSI driver module loaded
  170. mxc_lcdif lcd.19: can't get/select pinctrl
  171. mxc_sdc_fb fb.18: register mxc display driver lcd
  172. mxc_sdc_fb fb.18: NO mxc display driver found!
  173. imx_epdc_fb 20f4000.epdc: can't get/select pinctrl
  174. imx-sdma 20ec000.sdma: no iram assigned, using external mem
  175. imx-sdma 20ec000.sdma: loaded firmware 1.1
  176. imx-sdma 20ec000.sdma: initialized
  177. Serial: IMX driver
  178. 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
  179. console [ttymxc0] enabled
  180. 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX
  181. 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX
  182. serial: Freescale lpuart driver
  183. [drm] Initialized drm 1.1.0 20060810
  184. [drm] Initialized vivante 1.0.0 20120216 on minor 0
  185. brd: module loaded
  186. loop: module loaded
  187. nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
  188. nand: Samsung NAND 128MiB 3,3V 8-bit
  189. nand: 128MiB, SLC, page size: 2048, OOB size: 64
  190. Bad block table found at page 65472, version 0x01
  191. Bad block table found at page 65408, version 0x01
  192. 6 cmdlinepart partitions found on MTD device gpmi-nand
  193. Creating 6 MTD partitions on "gpmi-nand":
  194. 0x000000020000-0x000000120000 : "u-boot"
  195. 0x000000120000-0x000000180000 : "env"
  196. 0x000000180000-0x000000880000 : "linux"
  197. 0x000000880000-0x000007f60000 : "rootfs"
  198. 0x000007f60000-0x000007f80000 : "dtb"
  199. 0x000007f80000-0x000008000000 : "bbt"
  200. gpmi-nand 112000.gpmi-nand: driver registered.
  201. spi_imx 2008000.ecspi: probed
  202. CAN device driver interface
  203. flexcan 2090000.flexcan: device registered (reg_base=c09a8000, irq=142)
  204. flexcan 2094000.flexcan: device registered (reg_base=c09b0000, irq=143)
  205. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  206. usbcore: registered new interface driver usb-storage
  207. ci_hdrc ci_hdrc.1: EHCI Host Controller
  208. ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
  209. ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
  210. hub 1-0:1.0: USB hub found
  211. hub 1-0:1.0: 1 port detected
  212. mousedev: PS/2 mouse device common for all mice
  213. input: 20b8000.kpp as /devices/soc0/soc.0/2000000.aips-bus/20b8000.kpp/input/input0
  214. i2c-core: driver [isl29023] using legacy suspend method
  215. i2c-core: driver [isl29023] using legacy resume method
  216. snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc0
  217. i2c /dev entries driver
  218. i2c-core: driver [mag3110] using legacy suspend method
  219. i2c-core: driver [mag3110] using legacy resume method
  220. imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)
  221. cpuidle: using governor ladder
  222. cpuidle: using governor menu
  223. sdhci: Secure Digital Host Controller Interface driver
  224. sdhci: Copyright(c) Pierre Ossman
  225. sdhci-pltfm: SDHCI platform and OF driver helper
  226. mmc0: no vqmmc regulator found
  227. mmc0: no vmmc regulator found
  228. mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
  229. mmc1: no vqmmc regulator found
  230. mmc1: no vmmc regulator found
  231. mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
  232. Galcore version 4.6.9.9754
  233. leds-gpio leds.13: pins are not configured from the driver
  234. usbcore: registered new interface driver usbhid
  235. usbhid: USB HID core driver
  236. i2c-core: driver [cs42888] using legacy suspend method
  237. i2c-core: driver [cs42888] using legacy resume method
  238. fsl-ssi-dai 2028000.ssi: could not get ipg clock: -2
  239. fsl-ssi-dai: probe of 2028000.ssi failed with error -2
  240. imx-sgtl5000 sound.15: ASoC: CPU DAI (null) not registered
  241. imx-sgtl5000 sound.15: snd_soc_register_card failed (-517)
  242. platform sound.15: Driver imx-sgtl5000 requests probe deferral
  243. TCP: cubic registered
  244. NET: Registered protocol family 10
  245. sit: IPv6 over IPv4 tunneling driver
  246. NET: Registered protocol family 17
  247. can: controller area network core (rev 20120528 abi 9)
  248. NET: Registered protocol family 29
  249. can: raw protocol (rev 20120528)
  250. can: broadcast manager protocol (rev 20120528 t)
  251. can: netlink gateway (rev 20130117) max_hops=1
  252. 8021q: 802.1Q VLAN Support v1.8
  253. Key type dns_resolver registered
  254. VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
  255. imx-sgtl5000 sound.15: ASoC: CPU DAI (null) not registered
  256. imx-sgtl5000 sound.15: snd_soc_register_card failed (-517)
  257. platform sound.15: Driver imx-sgtl5000 requests probe deferral
  258. UBI: attaching mtd3 to ubi0
  259. Unable to handle kernel NULL pointer dereference at virtual address 00000000
  260. pgd = 80004000
  261. [00000000] *pgd=00000000
  262. Internal error: Oops: 80000005 [#1] PREEMPT SMP ARM
  263. Modules linked in:
  264. CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 3.10.17-1.0.2_ga+g33597e3 #2
  265. task: a8070780 ti: a807a000 task.ti: a807a000
  266. PC is at 0x0
  267. LR is at call_timer_fn.isra.30+0x24/0x88
  268. pc : [<00000000>] lr : [<80032cc4>] psr: 40000113
  269. sp : a807bea0 ip : a807bec0 fp : 00000000
  270. r10: 00000000 r9 : 80cdbb14 r8 : 00000000
  271. r7 : 00000100 r6 : a807a000 r5 : a807bec0 r4 : a807a020
  272. r3 : a807bea0 r2 : 00000101 r1 : 00000000 r0 : 00000000
  273. Flags: nZcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
  274. Control: 10c53c7d Table: 1000404a DAC: 00000015
  275. Process ksoftirqd/0 (pid: 3, stack limit = 0xa807a238)
  276. Stack: (0xa807bea0 to 0xa807c000)
  277. bea0: 80c5bc14 80c45c00 80cdb300 a807bec0 00000000 00200200 80c4a0c0 80032e8c
  278. bec0: a807bec0 a807bec0 80c6addc 00000041 80c4a084 00000004 a807a000 a807a030
  279. bee0: 00000001 00000004 00000100 8002d084 00000000 00000000 00000000 80c447a0
  280. bf00: 80cdb0c0 0000000a ffff8ba0 80c4a0c0 80c58324 04208040 a807a010 00000000
  281. bf20: a802f600 80c58324 00000000 00000001 00000000 00000000 00000000 8002d190
  282. bf40: a807a000 8004afc8 a8070780 a8075ea0 00000000 a802f600 8004ae8c 00000000
  283. bf60: 00000000 80043844 ffffff73 00000001 00000000 a802f600 00000000 00030003
  284. bf80: a807bf80 a807bf80 00000000 00000000 a807bf90 a807bf90 a807bfac a8075ea0
  285. bfa0: 80043790 00000000 00000000 8000e198 00000000 00000000 00000000 00000000
  286. bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
  287. bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 f3bd5f7f b57efa2f
  288. [<80032cc4>] (call_timer_fn.isra.30+0x24/0x88) from [<80032e8c>] (run_timer_softirq+0x164/0x1e4)
  289. [<80032e8c>] (run_timer_softirq+0x164/0x1e4) from [<8002d084>] (__do_softirq+0x110/0x1ec)
  290. [<8002d084>] (__do_softirq+0x110/0x1ec) from [<8002d190>] (run_ksoftirqd+0x30/0x44)
  291. [<8002d190>] (run_ksoftirqd+0x30/0x44) from [<8004afc8>] (smpboot_thread_fn+0x13c/0x234)
  292. [<8004afc8>] (smpboot_thread_fn+0x13c/0x234) from [<80043844>] (kthread+0xb4/0xb8)
  293. [<80043844>] (kthread+0xb4/0xb8) from [<8000e198>] (ret_from_fork+0x14/0x3c)
  294. Code: bad PC value
  295. ---[ end trace c065596c1944cb0b ]---
  296. Kernel panic - not syncing: Fatal exception in interrupt
  297. CPU1: stopping
  298. CPU: 1 PID: 0 Comm: swapper/1 Tainted: G D 3.10.17-1.0.2_ga+g33597e3 #2
  299. [<80013b94>] (unwind_backtrace+0x0/0xec) from [<800115a0>] (show_stack+0x10/0x14)
  300. [<800115a0>] (show_stack+0x10/0x14) from [<80012dc0>] (handle_IPI+0x108/0x118)
  301. [<80012dc0>] (handle_IPI+0x108/0x118) from [<80008558>] (gic_handle_irq+0x58/0x5c)
  302. [<80008558>] (gic_handle_irq+0x58/0x5c) from [<8000dd00>] (__irq_svc+0x40/0x70)
  303. Exception stack(0xa8097f50 to 0xa8097f98)
  304. 7f40: a8097f98 3b9aca00 87a7bf62 00000000
  305. 7f60: 80c5611c 80c560d0 81520130 00000001 875ad695 00000000 a8096000 00000000
  306. 7f80: 00000017 a8097f98 00000009 804434e8 00000113 ffffffff
  307. [<8000dd00>] (__irq_svc+0x40/0x70) from [<804434e8>] (cpuidle_enter_state+0x54/0xe4)
  308. [<804434e8>] (cpuidle_enter_state+0x54/0xe4) from [<80443634>] (cpuidle_idle_call+0xbc/0x154)
  309. [<80443634>] (cpuidle_idle_call+0xbc/0x154) from [<8000ecf0>] (arch_cpu_idle+0x10/0x54)
  310. [<8000ecf0>] (arch_cpu_idle+0x10/0x54) from [<80059a80>] (cpu_startup_entry+0x100/0x14c)
  311. [<80059a80>] (cpu_startup_entry+0x100/0x14c) from [<10627444>] (0x10627444)
  312. Rebooting in 1 seconds..
  313.  
  314. U-Boot 2013.07-00787-g36ed10c (Mar 24 2015 - 16:02:12)
  315.  
  316. CPU: Freescale i.MX6DL rev1.1 at 792 MHz
  317. Reset cause: SOFT
  318. Board: Ka-Ro TX6U-8010
  319. I2C: ready
  320. DRAM: 1 GiB
  321. VDDCORE set to 1421mV
  322. VDDSOC set to 1421mV
  323. NAND: 128 MiB
  324. MMC: FSL_SDHC: 0, FSL_SDHC: 1
  325. IPU HW Rev: 4
  326. Temperature: 57 C, calibration data 0x5814fa69
  327. CPU clock set to 792.000 MHz
  328. Baseboard: stk5-v3
  329. MAC addr from fuse: 00:0c:c6:7a:39:63
  330. Net: FEC
  331. Hit any key to stop autoboot: 0
  332. TX6DL U-Boot >
  333. TX6DL U-Boot >
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement