Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- smartctl 6.1 2013-03-16 r3800 [x86_64-apple-darwin12.3.0] (local build)
- Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Device Model: Hitachi HTS545025B9SA02
- Serial Number: 091031PBL2001SGW18WN
- LU WWN Device Id: 5 000cca 5e7cc4ad9
- Firmware Version: PB2AC60T
- User Capacity: 250,059,350,016 bytes [250 GB]
- Sector Size: 512 bytes logical/physical
- Rotation Rate: 5400 rpm
- Device is: Not in smartctl database [for details use: -P showall]
- ATA Version is: ATA8-ACS T13/1699-D revision 6
- SATA Version is: SATA 2.6, 1.5 Gb/s
- Local Time is: Thu May 15 15:03:56 2014 CEST
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF ENABLE/DISABLE COMMANDS SECTION ===
- SMART Enabled.
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x00) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Disabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 645) seconds.
- Offline data collection
- capabilities: (0x5b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- No Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 83) minutes.
- SCT capabilities: (0x003d) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000b 099 099 062 Pre-fail Always - 65538
- 2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
- 3 Spin_Up_Time 0x0007 232 232 033 Pre-fail Always - 1
- 4 Start_Stop_Count 0x0012 094 094 000 Old_age Always - 9632
- 5 Reallocated_Sector_Ct 0x0033 086 086 005 Pre-fail Always - 1023
- 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
- 8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0
- 9 Power_On_Hours 0x0012 071 071 000 Old_age Always - 13060
- 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
- 12 Power_Cycle_Count 0x0032 095 095 000 Old_age Always - 9273
- 160 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
- 191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 4578435137536
- 192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 498404884618
- 193 Load_Cycle_Count 0x0012 020 020 000 Old_age Always - 801761
- 194 Temperature_Celsius 0x0002 134 134 000 Old_age Always - 41 (Min/Max 14/48)
- 195 Hardware_ECC_Recovered 0x000a 100 100 000 Old_age Always - 0
- 196 Reallocated_Event_Count 0x0032 083 083 000 Old_age Always - 1205
- 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 43
- 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
- 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
- 223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0
- 254 Free_Fall_Sensor 0x0032 001 001 000 Old_age Always - 51539635705
- SMART Error Log Version: 1
- ATA Error Count: 1064 (device log contains only the most recent five errors)
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 1064 occurred at disk power-on lifetime: 13056 hours (544 days + 0 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 07 91 67 0e 41 Error: UNC 7 sectors at LBA = 0x010e6791 = 17721233
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 08 90 67 0e 40 00 00:02:50.800 READ DMA EXT
- 25 00 08 90 67 0e 40 00 00:02:46.700 READ DMA EXT
- ef 10 02 00 00 00 00 00 00:02:46.700 SET FEATURES [Enable SATA feature]
- ef 02 00 00 00 00 00 00 00:02:46.700 SET FEATURES [Enable write cache]
- ef aa 00 00 00 00 00 00 00:02:46.700 SET FEATURES [Enable read look-ahead]
- Error 1063 occurred at disk power-on lifetime: 13056 hours (544 days + 0 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 07 91 67 0e 41 Error: UNC 7 sectors at LBA = 0x010e6791 = 17721233
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 08 90 67 0e 40 00 00:02:46.700 READ DMA EXT
- ef 10 02 00 00 00 00 00 00:02:46.700 SET FEATURES [Enable SATA feature]
- ef 02 00 00 00 00 00 00 00:02:46.700 SET FEATURES [Enable write cache]
- ef aa 00 00 00 00 00 00 00:02:46.700 SET FEATURES [Enable read look-ahead]
- ef 03 46 00 00 00 00 00 00:02:46.700 SET FEATURES [Set transfer mode]
- Error 1062 occurred at disk power-on lifetime: 13052 hours (543 days + 20 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 46 42 0b 71 43 Error: UNC 70 sectors at LBA = 0x03710b42 = 57740098
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 d0 b8 0a 71 40 00 00:39:15.100 READ DMA EXT
- 25 00 28 48 28 b6 40 00 00:39:15.000 READ DMA EXT
- 25 00 18 b8 2d b6 40 00 00:39:15.000 READ DMA EXT
- 25 00 10 40 16 41 40 00 00:39:15.000 READ DMA EXT
- 25 00 20 c8 17 42 40 00 00:39:15.000 READ DMA EXT
- Error 1061 occurred at disk power-on lifetime: 13052 hours (543 days + 20 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 4d 3b 0b 71 43 Error: UNC 77 sectors at LBA = 0x03710b3b = 57740091
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 d8 b0 0a 71 40 00 00:38:02.100 READ DMA EXT
- 25 00 d8 b0 0a 71 40 00 00:37:54.500 READ DMA EXT
- ef 10 02 00 00 00 00 00 00:37:54.500 SET FEATURES [Enable SATA feature]
- ef 02 00 00 00 00 00 00 00:37:54.500 SET FEATURES [Enable write cache]
- ef aa 00 00 00 00 00 00 00:37:54.500 SET FEATURES [Enable read look-ahead]
- Error 1060 occurred at disk power-on lifetime: 13052 hours (543 days + 20 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 55 33 0b 71 43 Error: UNC 85 sectors at LBA = 0x03710b33 = 57740083
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 d8 b0 0a 71 40 00 00:37:54.500 READ DMA EXT
- ef 10 02 00 00 00 00 00 00:37:54.500 SET FEATURES [Enable SATA feature]
- ef 02 00 00 00 00 00 00 00:37:54.500 SET FEATURES [Enable write cache]
- ef aa 00 00 00 00 00 00 00:37:54.500 SET FEATURES [Enable read look-ahead]
- ef 03 46 00 00 00 00 00 00:37:54.500 SET FEATURES [Set transfer mode]
- SMART Self-test log structure revision number 1
- No self-tests have been logged. [To run self-tests, use: smartctl -t]
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement