SHOW:
|
|
- or go back to the newest paste.
| 1 | -- Here's an extremely basic timer program | |
| 2 | -- version 2013.09.20 | |
| 3 | ||
| 4 | --[[ use these two variables to specify which | |
| 5 | side the redstone signal comes IN and | |
| 6 | which sideyou want to pulse for OUT | |
| 7 | valid options are "left", "right","up", | |
| 8 | "down","front", or "back" | |
| 9 | notice how we use them later in the code | |
| 10 | so we only have to change them once | |
| 11 | at the top of the code instead of each | |
| 12 | time throughout the code. | |
| 13 | ||
| 14 | to install, make a computer and run the following command | |
| 15 | pastebin get 5pC0Njha startup | |
| 16 | then hold CTRL+R to reboot the computer and start the timer! | |
| 17 | hold CTRL+T to terminate the timer and type | |
| 18 | edit startup | |
| 19 | to be able to edit this timer program | |
| 20 | ]]-- | |
| 21 | ||
| 22 | - | local INPUT_SIDE = "top" -- change based on where your lever is |
| 22 | + | |
| 23 | - | local OUTPUT_SIDE = "back" -- change based on where your output side is |
| 23 | + | local args = { ... }
|
| 24 | - | local IDLE_TIME = 30 -- time (in sec) for cc to wait, rec 30, allows timer to survive reboot |
| 24 | + | local PHASE_LENGTH = 90 -- Standardlaenge je Phase an bzw aus |
| 25 | if #args > 0 then | |
| 26 | - | local PHASE_LENGTH = 90 -- time per each phase on - off |
| 26 | + | PHASE_LENGTH = 0 + args[1] |
| 27 | end | |
| 28 | if PHASE_LENGTH > 300 then | |
| 29 | PHASE_LENGTH = 300 -- 5 min bzw 300 sec Limit | |
| 30 | end | |
| 31 | ||
| 32 | local INPUT_SIDE = "top" -- change based on where your lever is | |
| 33 | local OUTPUT_SIDE = "back" -- change based on where your output side is | |
| 34 | - | while rs.getInput(INPUT_SIDE) do--while lever is ON |
| 34 | + | local IDLE_TIME = 30 -- time (in sec) for cc to wait, rec 30, allows timer to survive reboot |
| 35 | ||
| 36 | - | rs.setOutput(OUTPUT_SIDE,true)--turn output on |
| 36 | + | |
| 37 | --hold CTRL+T to stop the program | |
| 38 | - | rs.setOutput(OUTPUT_SIDE,false)--turn output off |
| 38 | + | |
| 39 | --wait for lever to be thrown, or check if red is already active after IDLE_TIME | |
| 40 | parallel.waitForAny(function() e = os.pullEvent("redstone"); return true end, function() sleep(IDLE_TIME); return true end)
| |
| 41 | --pulse the output | |
| 42 | while rs.getInput(INPUT_SIDE) do --while lever is ON | |
| 43 | write(".") --print a dot each time we pulse
| |
| 44 | rs.setOutput(OUTPUT_SIDE,true) --turn output on | |
| 45 | sleep(PHASE_LENGTH) | |
| 46 | rs.setOutput(OUTPUT_SIDE,false) --turn output off | |
| 47 | sleep(PHASE_LENGTH) | |
| 48 | end | |
| 49 | end |
