Pastebin launched a little side project called VERYVIRAL.com, check it out ;-) Want more features on Pastebin? Sign Up, it's FREE!
Guest

Untitled

By: a guest on Feb 28th, 2012  |  syntax: None  |  size: 11.98 KB  |  views: 40  |  expires: Never
download  |  raw  |  embed  |  report abuse  |  print
Text below is selected. Please press Ctrl+C to copy to your clipboard. (⌘+C on Mac)
  1. Texas Instruments X-Loader 1.5.0 (Aug 29 2011 - 12:52:49)
  2. OMAP3530-GP ES3.1
  3. Board revision: 0
  4. Reading boot sector
  5. Loading u-boot.bin from mmc
  6.  
  7.  
  8. U-Boot 2010.12 (Aug 22 2011 - 09:49:35)
  9.  
  10. OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 720 mHz
  11. Gumstix Overo board + LPDDR/NAND
  12. I2C:   ready
  13. DRAM:  256 MiB
  14. NAND:  256 MiB
  15. MMC:   OMAP SD/MMC: 0
  16. In:    serial
  17. Out:   serial
  18. Err:   serial
  19. Board revision: 0
  20. Tranceiver detected on mmc2
  21. No EEPROM on expansion board
  22. Die ID #7ed80004000000000403990c0c024010
  23. Net:   smc911x-0
  24. Hit any key to stop autoboot:  0
  25. reading boot.scr
  26.  
  27. ** Unable to read "boot.scr" from mmc 0:1 **
  28. reading uImage
  29.  
  30. 2914772 bytes read
  31. Booting from mmc ...
  32. ## Booting kernel from Legacy Image at 82000000 ...
  33.    Image Name:   Angstrom/2.6.39/overo
  34.    Image Type:   ARM Linux Kernel Image (uncompressed)
  35.    Data Size:    2914708 Bytes = 2.8 MiB
  36.    Load Address: 80008000
  37.    Entry Point:  80008000
  38.    Verifying Checksum ... OK
  39.    Loading Kernel Image ... OK
  40. OK
  41.  
  42. Starting kernel ...
  43.  
  44. Uncompressing Linux... done, booting the kernel.
  45. Linux version 2.6.39 (neil@cumulus) (gcc version 4.3.3 (GCC) ) #1 Mon Aug 15 19:04:09 PDT 2011
  46. CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
  47. CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
  48. Machine: Gumstix Overo
  49. Reserving 12582912 bytes SDRAM for VRAM
  50. Memory policy: ECC disabled, Data cache writeback
  51. OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
  52. SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
  53. Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
  54. Reprogramming SDRC clock to 332000000 Hz
  55. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 61952
  56. Kernel command line: console=ttyO2,115200n8 mpurate=720 vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
  57. PID hash table entries: 1024 (order: 0, 4096 bytes)
  58. Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
  59. Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
  60. Memory: 244MB = 244MB total
  61. Memory: 241308k/241308k available, 20836k reserved, 0K highmem
  62. Virtual kernel memory layout:
  63.     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
  64.     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
  65.     DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
  66.     vmalloc : 0xd0800000 - 0xf8000000   ( 632 MB)
  67.     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
  68.     modules : 0xbf000000 - 0xc0000000   (  16 MB)
  69.       .init : 0xc0008000 - 0xc0039000   ( 196 kB)
  70.       .text : 0xc0039000 - 0xc0574944   (5359 kB)
  71.       .data : 0xc0576000 - 0xc05b75c0   ( 262 kB)
  72. NR_IRQS:410
  73. IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
  74. Total of 96 interrupts on 1 active controller
  75. OMAP clockevent source: GPTIMER1 at 32768 Hz
  76. sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
  77. Console: colour dummy device 80x30
  78. Calibrating delay loop... 497.82 BogoMIPS (lpj=1941504)
  79. pid_max: default: 32768 minimum: 301
  80. Mount-cache hash table entries: 512
  81. CPU: Testing write buffer coherency: ok
  82. devtmpfs: initialized
  83. omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_core
  84. omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per
  85. omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup
  86. omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck.
  87. omap_hwmod: i2c1: softreset failed (waited 10000 usec)
  88. omap_hwmod: i2c2: softreset failed (waited 10000 usec)
  89. omap_hwmod: i2c3: softreset failed (waited 10000 usec)
  90. omap_hwmod: am35x_otg_hs: cannot be enabled (3)
  91. print_constraints: dummy:
  92. NET: Registered protocol family 16
  93. GPMC revision 5.0
  94. OMAP GPIO hardware version 2.5
  95. OMAP GPIO hardware version 2.5
  96. OMAP GPIO hardware version 2.5
  97. OMAP GPIO hardware version 2.5
  98. OMAP GPIO hardware version 2.5
  99. OMAP GPIO hardware version 2.5
  100. omap_mux_init: Add partition: #1: core, flags: 0
  101. Found NAND on CS0
  102. Registering NAND on CS0
  103. hw-breakpoint: debug architecture 0x4 unsupported.
  104. Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/720 MHz
  105. OMAP DMA hardware revision 4.0
  106. bio: create slab <bio-0> at 0
  107. print_constraints: vads7846: 3300 mV
  108. SCSI subsystem initialized
  109. usbcore: registered new interface driver usbfs
  110. usbcore: registered new interface driver hub
  111. usbcore: registered new device driver usb
  112. omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz
  113. twl4030: PIH (irq 7) chaining IRQs 368..375
  114. twl4030: power (irq 373) chaining IRQs 376..383
  115. twl4030: gpio (irq 368) chaining IRQs 384..401
  116. print_constraints: VUSB1V5: 1500 mV normal standby
  117. print_constraints: VUSB1V8: 1800 mV normal standby
  118. print_constraints: VUSB3V1: 3100 mV normal standby
  119. twl4030_usb twl4030_usb: Initialized TWL4030 USB module
  120. print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
  121. print_constraints: VDAC: 1800 mV normal standby
  122. print_constraints: VDVI: 1800 mV normal standby
  123. omap_i2c omap_i2c.3: bus 3 rev3.12 at 400 kHz
  124. Advanced Linux Sound Architecture Driver Version 1.0.24.
  125. Bluetooth: Core ver 2.16
  126. NET: Registered protocol family 31
  127. Bluetooth: HCI device and connection manager initialized
  128. Bluetooth: HCI socket layer initialized
  129. Bluetooth: L2CAP socket layer initialized
  130. Bluetooth: SCO socket layer initialized
  131. Switching to clocksource 32k_counter
  132. Switched to NOHz mode on CPU #0
  133. musb-hdrc: version 6.0, musb-dma, host, debug=0
  134. musb-hdrc musb-hdrc: MUSB HDRC host driver
  135. musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 1
  136. usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  137. usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  138. usb usb1: Product: MUSB HDRC host driver
  139. usb usb1: Manufacturer: Linux 2.6.39 musb-hcd
  140. usb usb1: SerialNumber: musb-hdrc
  141. hub 1-0:1.0: USB hub found
  142. hub 1-0:1.0: 1 port detected
  143. musb-hdrc musb-hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92
  144. NET: Registered protocol family 2
  145. IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
  146. TCP established hash table entries: 8192 (order: 4, 65536 bytes)
  147. TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
  148. TCP: Hash tables configured (established 8192 bind 8192)
  149. TCP reno registered
  150. UDP hash table entries: 256 (order: 0, 4096 bytes)
  151. UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  152. NET: Registered protocol family 1
  153. RPC: Registered udp transport module.
  154. RPC: Registered tcp transport module.
  155. RPC: Registered tcp NFSv4.1 backchannel transport module.
  156. VFS: Disk quotas dquot_6.5.2
  157. Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  158. Registering unionfs 2.5.9 (for 2.6.39-rc5)
  159. JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
  160. msgmni has been set to 471
  161. Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
  162. io scheduler noop registered
  163. io scheduler deadline registered
  164. io scheduler cfq registered (default)
  165. OMAP DSS rev 2.0
  166. Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
  167. omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
  168. omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
  169. omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
  170. console [ttyO2] enabled
  171. brd: module loaded
  172. loop: module loaded
  173. omap2-nand driver initializing
  174. ONFI flash detected
  175. NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)
  176. cmdlinepart partition parsing not available
  177. Creating 5 MTD partitions on "omap2-nand.0":
  178. 0x000000000000-0x000000080000 : "xloader"
  179. 0x000000080000-0x000000240000 : "uboot"
  180. 0x000000240000-0x000000280000 : "uboot environment"
  181. 0x000000280000-0x000000680000 : "linux"
  182. 0x000000680000-0x000010000000 : "rootfs"
  183. smsc911x: Driver version 2008-10-21.
  184. smsc911x smsc911x.0: eth0: Features changed: 0x00004800 -> 0x00004000
  185. smsc911x-mdio: probed
  186. eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
  187. net eth0: MAC Address: 00:15:c9:28:db:17
  188. smsc911x: Driver version 2008-10-21.
  189. usbcore: registered new interface driver asix
  190. usbcore: registered new interface driver cdc_ether
  191. cdc_ncm: 23-Apr-2011
  192. usbcore: registered new interface driver cdc_ncm
  193. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  194. ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
  195. ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
  196. ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
  197. ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
  198. usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
  199. usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  200. usb usb2: Product: OMAP-EHCI Host Controller
  201. usb usb2: Manufacturer: Linux 2.6.39 ehci_hcd
  202. usb usb2: SerialNumber: ehci-omap.0
  203. hub 2-0:1.0: USB hub found
  204. hub 2-0:1.0: 3 ports detected
  205. Initializing USB Mass Storage driver...
  206. usbcore: registered new interface driver usb-storage
  207. USB Mass Storage support registered.
  208. udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
  209. mousedev: PS/2 mouse device common for all mice
  210. twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
  211. i2c /dev entries driver
  212. OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
  213. Bluetooth: HCI UART driver ver 2.2
  214. Bluetooth: HCI H4 protocol initialized
  215. Bluetooth: HCI BCSP protocol initialized
  216. Bluetooth: HCILL protocol initialized
  217. cpuidle: using governor ladder
  218. cpuidle: using governor menu
  219. usbcore: registered new interface driver usbhid
  220. usbhid: USB HID core driver
  221. usbcore: registered new interface driver snd-usb-audio
  222. overo SoC init
  223. asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok
  224. ALSA device list:
  225.   #0: overo
  226. oprofile: hardware counters not available
  227. oprofile: using timer interrupt.
  228. TCP cubic registered
  229. NET: Registered protocol family 17
  230. NET: Registered protocol family 15
  231. Bluetooth: RFCOMM TTY layer initialized
  232. Bluetooth: RFCOMM socket layer initialized
  233. Bluetooth: RFCOMM ver 1.11
  234. Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  235. Bluetooth: BNEP filters: protocol multicast
  236. Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  237. Registering the dns_resolver key type
  238. VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
  239. ThumbEE CPU extension supported.
  240. omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu
  241. omap2_set_init_voltage: Unable to put vdd_mpu to its init voltage
  242.  
  243. Power Management for TI OMAP3.
  244. sr_init: No PMIC hook to init smartreflex
  245. smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
  246. smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
  247. clock: disabling unused clocks to save power
  248. fbcvt: 1024x768@60: CVT Name - .786M3-R
  249. Console: switching to colour frame buffer device 128x48
  250. regulator_init_complete: VDAC: incomplete constraints, leaving on
  251. regulator_init_complete: vads7846: incomplete constraints, leaving on
  252. twl_rtc twl_rtc: setting system clock to 2000-01-01 00:04:44 UTC (946685084)
  253. Waiting for root device /dev/mmcblk0p2...
  254. mmc0: host does not support reading read-only switch. assuming write-enable.
  255. mmc0: new SD card at address aaaa
  256. mmcblk0: mmc0:aaaa SU02G 1.84 GiB
  257. mmcblk0: detected capacity change from 0 to 1977614336
  258.  mmcblk0: p1 p2
  259. EXT3-fs: barriers not enabled
  260. mmc1: new SDIO card at address 0001
  261. kjournald starting.  Commit interval 5 seconds
  262. EXT3-fs (mmcblk0p2): using internal journal
  263. EXT3-fs (mmcblk0p2): recovery complete
  264. EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
  265. VFS: Mounted root (ext3 filesystem) on device 179:2.
  266. devtmpfs: mounted
  267. Freeing init memory: 196K
  268. INIT: version 2.86 booting
  269. Please wait: booting...
  270. Starting udev
  271. udevd (92): /proc/92/oom_adj is deprecated, please use /proc/92/oom_score_adj instead.
  272. ads7846 spi1.0: touchscreen, irq 274
  273. ads7846 spi1.0: no device detected, test read result was 0x00000000
  274. usbcore: registered new interface driver usbserial
  275. USB Serial support registered for generic
  276. usbcore: registered new interface driver usbserial_generic
  277. usbserial: USB Serial Driver core
  278. USB Serial support registered for GSM modem (1-port)
  279. usbcore: registered new interface driver option
  280. option: v0.7.2:USB Driver for GSM modems
  281. lib80211: common routines for IEEE802.11 drivers
  282. cfg80211: Calling CRDA to update world regulatory domain
  283. libertas_sdio: Libertas SDIO driver
  284. libertas_sdio: Copyright Pierre Ossman