WRT110 v1.0.07 boot transcript

U-Boot 1.1.3 (Jan 10 2008 - 12:41:46)

Board: RT2880 DRAM:  16 MB

 twe0 set to <NULL>

 toe0 set to <NULL>

 Set info->start[0]=BC400000
flash_protect ON: from 0xBC400000 to 0xBC42480B
protect on 0
protect on 1
protect on 2
flash_protect ON: from 0xBC430000 to 0xBC43FFFF
protect on 3


============================================
ASIC -VerB/C (MAC to Phy Mode)
DRAM COMPONENT=128Mbits
DRAM BUS=16BIT
Total memory = 16Mbytes
Date:Jan 10 2008  Time:12:41:46
============================================
 D-CACHE set to 4 way
 I-CACHE set to 4 way

 ##### The CPU freq = 266 MHZ ####

SDRAM bus set to 16 bit
 SDRAM size =16 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   5: Load ucos code to SDRAM via TFTP.
 0

3: System Boot system code via Flash.
## Booting image at bc450000 ...
   Image Name:   Linux Kernel Image
   Created:      2009-12-01  10:01:53 UTC
System Control Status = 0x02110084
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    776616 Bytes = 758.4 kB
   Load Address: 8a000000
   Entry Point:  8818a040
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8818a040) ...
## Giving linux memsize in MB, 16

Starting kernel ...


THIS IS ASIC
ramsize = 16 MBytes
rambase not set, set to default (0x08000000)
MEMORY DESCRIPTOR dump:
[0,88208c50]: base<08000000> size<01000000> type<Free RAM memory>

 The CPU feqenuce set to 266 MHz
CPU revision is: 0001906c
icache: sets:256, ways:4, linesz:16 ,total:16384, waybit:12, flags:0x0
dcache: sets:256, ways:4, linesz:16 ,total:16384, waybit:12, flags:0x0
i waysize = 4096, d waysize = 4096, i sets= 256, d sets=256
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, linesize 16 bytes.
[setup_scache]:1051
Linux version 2.4.30 (mavis@localhost.localdomain) (gcc version 3.3.6) #1 Tue Dec 1 17:58:24 CST 2009
Determined physical RAM map:
 memory: 01000000 @ 08000000 (usable)
On node 0 totalpages: 36864
zone(0): 36864 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3
cause = 50c08308, status = 1000fc00
calculating r4koff... 00144b50(1330000)
CPU frequency 133.00 MHz
Using 133.000 MHz high precision timer.
Calibrating delay loop... 265.42 BogoMIPS
Memory: 12700k/16384k available (1565k kernel code, 3684k reserved, 104k data, 100k init, 0k highmem)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 2048 (order: 1, 8192 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
pci.c pcibios_init():835
BAR0 at slot 0 = 8
pci.c pcibios_fixup_resources():635
bus = 0, dev = 0, fun = 0
dev= 0x883bbc00
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
Ralink RT2880 gpio mode 00000007
Ralink gpio driver initialized
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x300500 (irq = 9) is a 16550A
ttyS01 at 0x300c00 (irq = 8) is a 16550A
Initialziing the Watchdog control module ... successful
Initialziing the WPS LED control module ... successful
RA2880 Ethernet Driver Initilization. v1.01  128 rx/tx descriptors allocated!
Netlink init ok!
PROC INIT OK!
ICPLUS 175C config LAN_WAN finished (evaluation board)
rdm_major = 254
PPP generic driver version 2.4.2
PPP BSD Compression module registered
FLASH_API: MAN_ID=7F DEV_ID=22F9 SIZE=4MB
physmap flash device: 4000000 at bc400000
 Amd/Fujitsu Extended Query Table v1.1 at 0x0040
number of CFI chips: 1
Region0: SectorSize=0x2000 SectorNum=8
Region1: SectorSize=0x10000 SectorNum=63
cfi_cmdset_0002: Using word write method.
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
mtd: Giving out device 0 to RT2880 SOC Physically mapped flash
Using physmap partition definition
Creating 6 MTD partitions on "RT2880 SOC Physically mapped flash":
0x00000000-0x00050000 : "uBoot"
mtd: Giving out device 1 to uBoot
0x00050000-0x00130000 : "Linux Kernel"
mtd: Giving out device 2 to Linux Kernel
0x00130000-0x00390000 : "RootFS"
mtd: Giving out device 3 to RootFS
0x00390000-0x003e0000 : "LANGUAGE_PACK"
mtd: Giving out device 4 to LANGUAGE_PACK
0x003e0000-0x003f0000 : "NVRAM"
mtd: Giving out device 5 to NVRAM
0x003f0000-0x00400000 : "NVRAM_FACTORY"
mtd: Giving out device 6 to NVRAM_FACTORY
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.1 (1152 buckets, 9216 max) - 316 bytes per conntrack
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
ip_tables: (C) 2000-2002 Netfilter core team, Type=Linux
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.  http://snowman.net/projects/ipt_recent/
ipt_time loading
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 100k freed
console started
trying to start /sbin/init
Algorithmics/MIPS FPU Emulator v1.5
Hit enter to continue...
Calculating Firmware MD5...
MD5 ("e9283e60255b55783e85096f9599a929")
mtd_write: Write 65536 bytes data to 3E0000
mount language pack: : Inappropriate ioctl for device
killall: udhcpd: no process killed
System Start...
/***************************************************************************/
/**FW Version : 1.0.07_build_002_01_20091123  !!
/***************************************************************************/
Setting ra0 configuration....
wps_utility : init mode
wps_utility : PIN-Enrollee-Manual mode
WPS PIN code for this device: 18908589
ra0       mac:
[0x0000102c]:44031e46
httpd.c->main(1072),cur_sysinfo.uptime=18,HNAP_uptime=0
uptime<50
httpd open port:80
services.c->start_linuxigd(716),============  start_linuxigd()!!  ============
/tmp/del_route: cannot open
services.c->start_wsc_upnp(1478),============  start_wsc_upnp()!!  ============
UPNP start !!!
Unknown config line:disable_allowed = no
libupnp: using UDP SSDP_PORT = 1900
rmmod: /lib/ipt_404.o: Success
killall: udhcpc: no process killed


BusyBox v1.2.1 (2009.12.01-09:59+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.

***********DISCONNECT WAN*******************
:/> rmmod: /lib/ipt_404.o: Success
check_WPS_status : WSCStatus is 3 now...STATUS_WSC_LINK_UP
killall: udhcpc: no process killed
wan services stoped
0