[root@asterisk-vgdl ~]# cat /etc/wanpipe/wanpipe1.conf
#================================================
# WANPIPE1 Configuration File
#================================================
#
# Date: Wed Dec  6 20:29:03 UTC 2006
#
# Note: This file was generated automatically
#       by /usr/local/sbin/setup-sangoma program.
#
#       If you want to edit this file, it is
#       recommended that you use wancfg program
#       to do so.
#================================================
# Sangoma Technologies Inc.
#================================================

[devices]
wanpipe1 = WAN_AFT_TE1, Comment

[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment

[wanpipe1]
CARD_TYPE       = AFT
S514CPU         = A
CommPort        = PRI
AUTO_PCISLOT    = NO
PCISLOT         = 4
PCIBUS          = 10
FE_MEDIA        = E1
FE_LCODE        = HDB3
FE_FRAME        = CRC4
FE_LINE         = 1
TE_CLOCK        = NORMAL
TE_REF_CLOCK    = 0
TE_SIG_MODE     = CAS
TE_HIGHIMPEDANCE        = NO
TE_RX_SLEVEL    = 430
HW_RJ45_PORT_MAP = DEFAULT
LBO             = 120OH
FE_TXTRISTATE   = NO
MTU             = 1500
UDPPORT         = 9000
TTL             = 255
IGNORE_FRONT_END        = NO
TDMV_SPAN               = 1
TDMV_DCHAN              = 0
TE_AIS_MAINTENANCE = NO         #NO: defualt  YES: Start port in AIS Blue Alarm and keep line down
                                #wanpipemon -i w1g1 -c Ttx_ais_off to disable AIS maintenance mode
                                                                #wanpipemon -i w1g1 -c Ttx_ais_on to enable AIS maintenance mode
TDMV_HW_DTMF            = NO            # YES: receive dtmf events from hardware
TDMV_HW_FAX_DETECT              = NO            # YES: receive fax 1100hz events from hardware
HWEC_OPERATION_MODE     = OCT_NORMAL    # OCT_NORMAL: echo cancelation enabled with nlp (default)
                                                                                # OCT_SPEECH: improves software tone detection by disabling NLP (echo possible)
                                                                                # OCT_NO_ECHO:disables echo cancelation but allows VQE/tone functions.
HWEC_DTMF_REMOVAL       = NO    # NO: default  YES: remove dtmf out of incoming media (must have hwdtmf enabled)
HWEC_NOISE_REDUCTION    = NO    # NO: default  YES: reduces noise on the line - could break fax
HWEC_ACUSTIC_ECHO       = NO    # NO: default  YES: enables acustic echo cancelation
HWEC_NLP_DISABLE        = NO    # NO: default  YES: guarantees software tone detection (possible echo)
HWEC_TX_AUTO_GAIN       = 0     # 0: disable   -40-0: default tx audio level to be maintained (-20 default)
HWEC_RX_AUTO_GAIN       = 0     # 0: disable   -40-0: default tx audio level to be maintained (-20 default)
HWEC_TX_GAIN            = 0             # 0: disable   -24-24: db values to be applied to tx signal
HWEC_RX_GAIN            = 0             # 0: disable   -24-24: db values to be applied to tx signal

[w1g1]
ACTIVE_CH       = ALL
TDMV_HWEC       = NO
MTU             = 8