U-Boot SPL 2012.07-00004-ge092c4d (Jul 31 2012 - 11:26:47)
Texas Instruments Revision detection unimplemented


U-Boot 2012.07-00004-ge092c4d (Jul 31 2012 - 11:26:47)

OMAP3530-GP ES2.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 mHz
OMAP3 Beagle board + LPDDR/NAND
I2C:   ready
DRAM:  128 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0
*** Warning - bad CRC, using default environment

<Reset/User Button:>

U-Boot SPL 2013.01.01-00006-gef50daa (Feb 01 2013 - 11:44:58)
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img


U-Boot 2013.01.01-00006-gef50daa (Feb 01 2013 - 11:44:58)

OMAP3530-GP ES2.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 mHz
OMAP3 Beagle board + LPDDR/NAND
I2C:   ready
DRAM:  128 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Beagle Rev Ax/Bx
timed out in wait_for_pin: I2C_STAT=1000
No EEPROM on expansion board
timed out in wait_for_bb: I2C_STAT=1000
No EEPROM on expansion board
Die ID #160600020000000004013ebf0c010011
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 1.400
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 480ab000 using PIO, IRQ 0
Net:   usb_ether
Hit any key to stop autoboot:  0
mmc0 is current device
gpio: pin 173 (gpio 173) value is 1
gpio: pin 7 (gpio 7) value is 0
SD/MMC found on device 0
reading uEnv.txt
144 bytes read in 3 ms (46.9 KiB/s)
Loaded environment from uEnv.txt
Importing environment from mmc ...
reading user.scr
509 bytes read in 3 ms (165 KiB/s)
Running user.scr script from mmc ...
## Executing script at 80200000
Starting NAND UPGRADE, do not REMOVE SD CARD or POWER till Complete
reading MLO
46748 bytes read in 39 ms (1.1 MiB/s)
HW ECC selected

NAND erase: device 0 offset 0x0, size 0x80000
Skipping bad block at  0x00040000
Erasing at 0x60000 -- 100% complete.
OK

NAND write: device 0 offset 0x0, size 0x20000
 131072 bytes written: OK

NAND write: device 0 offset 0x20000, size 0x20000
 131072 bytes written: OK

NAND write: device 0 offset 0x40000, size 0x20000
Skip bad block 0x00040000
 131072 bytes written: OK

NAND write: device 0 offset 0x60000, size 0x20000
 131072 bytes written: OK
reading u-boot.img
358868 bytes read in 265 ms (1.3 MiB/s)
HW ECC selected

NAND erase: device 0 offset 0x80000, size 0x160000
Erasing at 0x1c0000 -- 100% complete.
OK

NAND write: device 0 offset 0x80000, size 0x170000
 1507328 bytes written: OK

NAND erase: device 0 offset 0x260000, size 0x20000
Erasing at 0x260000 -- 100% complete.
OK
FLASH UPGRADE Complete
Booting from nand ...

NAND read: device 0 offset 0x280000, size 0x400000
 4194304 bytes read: OK

(pull out sd & hit reset)

U-Boot SPL 2013.01.01-00006-gef50daa (Feb 01 2013 - 11:44:58)


U-Boot 2013.01.01-00006-gef50daa (Feb 01 2013 - 11:44:58)

OMAP3530-GP ES2.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 mHz
OMAP3 Beagle board + LPDDR/NAND
I2C:   ready
DRAM:  128 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Beagle Rev Ax/Bx
timed out in wait_for_pin: I2C_STAT=0
No EEPROM on expansion board
timed out in wait_for_pin: I2C_STAT=0
No EEPROM on expansion board
Die ID #160600020000000004013ebf0c010011
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 1.400
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 480ab000 using PIO, IRQ 0
Net:   usb_ether
Hit any key to stop autoboot:  0
OMAP3 beagleboard.org #