Advertisement
sporker

7206-NPE-G2 interface stats

Dec 7th, 2012
115
0
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 10.89 KB | None | 0 0
  1. 7206/NPE-G2 Gig0/3 interface info (counters reset about 16 hours ago)
  2.  
  3. of note here, output drops, output flow control enabled:
  4.  
  5. output flow-control is XON, input flow-control is unsupported
  6. Input queue: 0/75/0/15 (size/max/drops/flushes); Total output drops: 9570
  7.  
  8. l3-router#sh interfaces gigabitEthernet 0/3
  9. GigabitEthernet0/3 is up, line protocol is up
  10. Hardware is MV64460 Internal MAC, address is 0007.b3c3.f019 (bia 0007.b3c3.f019)
  11. Description: local server subnet (native vlan), trunk to 3560
  12. MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
  13. reliability 255/255, txload 19/255, rxload 23/255
  14. Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set
  15. Keepalive set (10 sec)
  16. Full-duplex, 1000Mb/s, media type is RJ45
  17. ?? -->>output flow-control is XON, input flow-control is unsupported
  18. ARP type: ARPA, ARP Timeout 04:00:00
  19. Last input 00:00:00, output 00:00:00, output hang never
  20. Last clearing of "show interface" counters 1d04h
  21. Input queue: 0/75/0/15 (size/max/drops/flushes); Total output drops: 9570 <<--
  22. Queueing strategy: fifo
  23. Output queue: 0/40 (size/max)
  24. 5 minute input rate 93407000 bits/sec, 14789 packets/sec
  25. 5 minute output rate 76439000 bits/sec, 13517 packets/sec
  26. 1017374526 packets input, 1652284061 bytes, 0 no buffer
  27. Received 55861 broadcasts, 0 runts, 0 giants, 0 throttles
  28. 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
  29. 0 watchdog, 1424775 multicast, 0 pause input
  30. 0 input packets with dribble condition detected
  31. 999128260 packets output, 2331441042 bytes, 0 underruns
  32. 0 output errors, 0 collisions, 0 interface resets
  33. 0 unknown protocol drops
  34. 0 babbles, 0 late collision, 0 deferred
  35. 0 lost carrier, 0 no carrier, 0 pause output
  36. 0 output buffer failures, 0 output buffers swapped out
  37.  
  38. Of note here:
  39.  
  40. flow control not mentioned - MAC Status: Link is UP, Speed is 1000Mbps, Duplex is Full, Interface: GMII
  41. "tx_end_count" incrementing - tx_end_count = 1619071635
  42. RX MAC drops - RX MAC Discard Frame 1394180
  43.  
  44. l3-router#sh controllers gigabitEthernet 0/3
  45. Interface GigabitEthernet0/3 (idb 0x7268A60)
  46. Hardware is MV64460 Internal MAC (Revision MV64460-Ethernet)
  47. network link is up
  48. Config is 1Gbps, Full Duplex
  49. Selected media-type is RJ45
  50. GBIC is not present
  51. Ethernet Unit Global Registers:
  52. PHY Address = 0x00000820 SMI (PHY Control) = 0x0C021000
  53. Default Address (Err) = 0xFE200000 Default ID (Err) = 0x000001D1
  54. Interrupt Cause = 0x00000C10 Interrupt Mask = 0x0000108E
  55. Error Address = 0xD7FC0000 Internal Addr Error = 0x00000000
  56. Port Pad Calibration = 0x0013000B Base Address 0 = 0xD7FC0002
  57. Size (BA0) = 0x00030000 Base Address 1 = 0x78002D00
  58. Size (BA1) = 0x03FF0000 Base Address 2 = 0x00000000
  59. Size (BA2) = 0x00000000 Base Address 3 = 0x00000000
  60. Size (BA3) = 0x00000000 Base Address 4 = 0x00000000
  61. Size (BA4) = 0x00000000 Base Address 5 = 0x00000000
  62. Size (BA5) = 0x00000000 Header Retarget Base = 0x00000000
  63. Header Retarget Ctrl = 0x00000000 High Address Remap 0 = 0x00000000
  64. High Address Remap 1 = 0x00000000 Base Address Enable = 0x0000003C
  65. Port Access Protect 0 = 0x0000000F Port Access Protect 1 = 0x0000000F
  66. Port Access Protect 2 = 0x0000000F
  67. MAC Specific Registers:
  68. Port Cfg PxC = 0x00000000 Port Cfg Extd PxCX = 0x00000000
  69. MII Serial Params = 0x00218823 GMII Serial Params = 0x00000006
  70. VLAN EtherType EVLANE = 0x00000000 MAC Addr Low MACAL = 0x0000F019
  71. MAC Addr High MACAH = 0x0007B3C3 SDMA Config SDC = 0x01002005
  72. PORT SERIAL CTRL PSC = 0x00E2A60D PORT STATUS PS = 0x0000041E
  73. TX Queue Cmd TQC = 0x00000000 TxQ Fixed Prio TQFPC = 0x00000001
  74. MTU (Token-Bucket) MTU = 0x00000000 INTR CAUSE IC = 0x80000005
  75. INTR CAUSE EXT ICE = 0x00000000 Intr Mask PIM = 0x00080804
  76. Extend Intr Mask PEIM = 0x00000101 RXQ Desc Ptr 0 CRDP0 = 0xD7FC6100
  77. RX Queue Cmd RQC = 0x0003FE01 TXQ Desc Ptr 0 TCQDP0 = 0xD7FC86E0
  78. TX Curr Desc TCSDP = 0xD7FC86E0
  79.  
  80. MAC Serial Port is ENABLED
  81. MAC Autoneg Capability: [Speed] [Duplex] [Flow Control]
  82. MAC Status: Link is UP, Speed is 1000Mbps, Duplex is Full, Interface: GMII
  83.  
  84. RX Queue [0] is ENABLED
  85.  
  86. PHY Registers:
  87. PHY is Marvell 88E1146C (Rev D0), address 0x2
  88. Control = 0x1000 Status = 0x796D
  89. PHY ID 1 = 0x0141 PHY ID 2 = 0x0CD4
  90. Auto Neg Advertisement = 0x0000 Link Partner Ability = 0xC001
  91. Auto Neg Expansion = 0x000D Next Page Tx = 0x2001
  92. Link Partner Next Page = 0x4B02 1000BaseT Control = 0x0200
  93. 1000BaseT Status = 0x3800 Extended Status = 0x3000
  94. PHY Specific Control = 0x0008 PHY Specific Status = 0xAC00
  95. Interrupt Enable = 0x6C00 Interrupt Status = 0x0000
  96. Ext PHY Spec Control = 0x0CE2 Receive Error Counter = 0x0000
  97. LED Control = 0x4101
  98. Ext PHY Spec Control 2 = 0x000A Ext PHY Spec Status = 0x840B
  99. PHY says Link is UP, Speed 1000Mbps, Full-Duplex [AUTONEG Done]
  100. Physical Interface - RJ45
  101. AUTONEG - Our ability is 1000M/FD
  102. AUTONEG - Partner ability is 1000M/FD
  103.  
  104. IDB Information:
  105. lc_ip_turbo_fs = 0x5C144, ip_routecache = 0x11 (dfs = 0/mdfs = 0)
  106. rx cache size = 1000, rx cache end = 872
  107. max_mtu = 1524
  108. Software MAC address filter(hash:length/addr/mask/hits):
  109. need_af_check = 0
  110. 0x00: 0 ffff.ffff.ffff 0000.0000.0000 0
  111. 0x58: 0 0100.5e00.0006 0000.0000.0000 0
  112. 0x5B: 0 0100.5e00.0005 0000.0000.0000 0
  113. 0xAA: 0 0007.b3c3.f019 0000.0000.0000 0
  114. 0xC0: 0 0100.0ccc.cccc 0000.0000.0000 0
  115. 0xC0: 1 0180.c200.0002 0000.0000.0000 0
  116. 0xC5: 0 0180.c200.0007 0000.0000.0000 0
  117.  
  118. Internal Driver Information:
  119. RX Ring base: 0xD7FC6000
  120. TX Ring base: 0xD7FC7000
  121. Software RX Head: 0xD7FC6060
  122. Hardware RX Head: 0xD7FC66A0
  123. Software TX Head: 0xD7FC86E0
  124. Hardware TX Head: 0xD7FC8CE0
  125. ring sizes: RX = 128, TX = 256
  126. rx_particle_size: 512
  127. rx_pak = 0x0705B30C
  128. rx_head = 3
  129. rx_discard = FALSE
  130. tx_head = 183, tx_count = 0
  131. chip_state = 2, ds->tx_limited = 0
  132. throttled = 0, enabled = 0, disabled = 10
  133. reset=4(init=1, restart=3), auto_restart=8
  134. tx_underflow = 0, tx_overflow = 0, tx_end_count = 1619071635 <<--???
  135. rx_nobuffer = 0, rx_overrun = 0
  136. rx_no_descriptors = 0, rx_interrupt_count = 875592461
  137. rx_crc_error = 0, rx_too_big = 0, rx_resource_error = 0
  138. rx_sop_eop_error = 0
  139. tqc = 0xF1002C48, cause = 0xF1002C60, cause_ext = 0xF1002C64
  140. Address Filter:
  141. Promiscuous mode OFF
  142. (All other entries are empty)
  143.  
  144. Statistics:
  145.  
  146. Receive and Transmit Statistics:
  147. RX Good Octets 776744696423 TX Good Octets 678463220924
  148. RX Good Packets 1021437205 TX Good Packets 1001584041
  149. RX Bad Octets 0
  150. RX Bad Packets 0
  151. RX Broadcast Packets 22085 TX Broadcast Packets 50457
  152. RX Multicast Packets 1427475 TX Multicast Packets 36064
  153.  
  154. Error Statistics:
  155. TX MAC Error 0
  156. TX Excess Collisions 0
  157. RX Bad MAC Ctrl Frame 0
  158. RX Good Flow Control 0
  159. RX Bad Flow Control 0
  160. RX Undersize Paks 0
  161. RX Oversize Paks 0
  162. RX Fragments 0
  163. RX Jabber Paks 0
  164. RX MAC Error Events 0
  165. RX Bad CRC Events 0
  166. RX Collisions 0
  167. RX Late Collisions 0
  168. RX MAC Discard Frame 1394180 <<--
  169. RX MAC Overrun Frame 0
  170.  
  171. Total Packets (RX and TX), including errors:
  172. 0 -> 64 116356216
  173. 65 -> 127 736455582
  174. 128 -> 255 174427602
  175. 256 -> 511 71188090
  176. 512 -> 1023 51656863
  177. 1024 -> max 873069856
  178.  
  179. Of note here:
  180.  
  181. -Protocol DEC MOP??
  182. -I'm not clear on what an abnormal amount of process-switched traffic is when doing all this vlan subinterface config on this router.
  183.  
  184. l3-router#sh interfaces gigabitEthernet 0/3 switching
  185. GigabitEthernet0/3 local server subnet (native vlan), trunk to 3560
  186. Throttle count 0
  187. Drops RP 583 SP 0
  188. SPD Flushes Fast 8335 SSE 0
  189. SPD Aggress Fast 0
  190. SPD Priority Inputs 36711331 Drops 68
  191.  
  192. Protocol IP
  193. Switching path Pkts In Chars In Pkts Out Chars Out
  194. Process 129225989 1047129416 90002659 925255253
  195. Cache misses 0 - - -
  196. Fast 3526253814 2587806504 299605491 2864744805
  197. Auton/SSE 0 0 0 0
  198.  
  199. Protocol DEC MOP
  200. Switching path Pkts In Chars In Pkts Out Chars Out
  201. Process 0 0 56943 4384611
  202. Cache misses 0 - - -
  203. Fast 0 0 0 0
  204. Auton/SSE 0 0 0 0
  205.  
  206. Protocol ARP
  207. Switching path Pkts In Chars In Pkts Out Chars Out
  208. Process 4348959 260937540 19983778 1221729012
  209. Cache misses 0 - - -
  210. Fast 0 0 21 1344
  211. Auton/SSE 0 0 0 0
  212.  
  213. Protocol CDP
  214. Switching path Pkts In Chars In Pkts Out Chars Out
  215. Process 124694 52246786 564430 214145674
  216. Cache misses 0 - - -
  217. Fast 0 0 0 0
  218. Auton/SSE 0 0 0 0
  219.  
  220. Protocol Other
  221. Switching path Pkts In Chars In Pkts Out Chars Out
  222. Process 970527 217977586 3420592 205235520
  223. Cache misses 0 - - -
  224. Fast 0 0 0 0
  225. Auton/SSE 0 0 0 0
  226.  
  227. NOTE: all counts are cumulative and reset only after a reload.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement