API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Dec 31st, 2016
630
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 19.74 KB | None | 0 0
raw download clone embed print report
  1. Boot reached stage 13
  2. Boot reached stage 12
  3. Valid CRC found in flash restoring env...
  4. Boot reached stage 11
  5. hw_config_id 65535: 'hw_PCIe_ep'
  6. UART1 enabled: GPIO_PIN1 (input) Rx, GPIO_PIN9 (output) Tx
  7. Cold boot
  8. Reset status: 0x00000001
  9. PCIe early init, done@194ms
  10.  
  11. Info: data uncached: addr=0xc0000000 size=1024MB
  12. Info: text at 0x88014000, stack at 0x88013ffc(8192), heap at 0x88000000(73728), uboot size 173140
  13. Info: i-cache is enabled
  14. Info: d-cache is enabled
  15. Info: CPU freq is 500000000, dev freq is 125000000
  16.  
  17. Info: Quantenna U-Boot version:v36.7.0.30
  18. Info: build date 'Dec 04 2014', time '22:03:18'
  19.  
  20. SPI flash info:
  21. name : mx25l12836e
  22. jedec_id : 0xc22018
  23. sector size : 65536
  24. number of sector : 256
  25. frequency : 104000000
  26. flags : 0x0
  27. lock :
  28. DDR_INIT: type = 16, speed = 3, size = 134217728
  29. 400MHz
  30. init board as PCIe End Point mode
  31. PCIe Shmem BAR2=0x10000 Len:64k
  32. PCIe Sysctl BAR0=0xe0000000 Len:64k
  33. PCIe DMA BAR3=0xe9000000 Len:64k
  34. BDA at 0x80002000
  35. In: serial
  36. Out: serial
  37. Err: serial
  38. Boot reached stage 64
  39. error: no emac enabled
  40. No ethernet found.
  41. Boot reached stage -64
  42. Hit any key to stop autoboot: 0
  43. Polling for PCIe Link up
  44. Waiting for handshake start
  45. PCI memory region is little endian
  46. Host memory start address is 0x41500000
  47. PCIe MSI Interrupt Support
  48. setup_atu_msi: msi_addr=a0000000
  49. 0:MSI64: Host:0x0a0000000 EP:0xcfff0000
  50. 1:Mem: EP(0x0->0xbfffffff) Host(0x41500000->0x14fffff)
  51. 2:BD: EP(0xcffd0000->0xcffeffff) Host(dynamic alloc in RC)
  52. Ready to load firmware....
  53. PCIe Load FW[0] 0x18800000->0x83000000 Sz:1048576...
  54. done
  55. PCIe Load FW[1] 0x18800000->0x83100000 Sz:1048576...
  56. done
  57. PCIe Load FW[2] 0x18800000->0x83200000 Sz:1048576...
  58. done
  59. PCIe Load FW[3] 0x18800000->0x83300000 Sz:1048576...
  60. done
  61. PCIe Load FW[4] 0x18800000->0x83400000 Sz:356135...
  62. done
  63. PCIe Gen: 2
  64. PCIe Loadaddr:0x83000000
  65. Boot reached stage 1
  66. ## Booting kernel from Legacy Image at 83000000 ...
  67. Boot reached stage 2
  68. Boot reached stage 3
  69. Image Name: topaz-linux
  70. Image Type: arc Linux Kernel Image (lzma compressed)
  71. Data Size: 4542247 Bytes = 4.3 MB
  72. Load Address: 8492c000
  73. Entry Point: 8492c000
  74. Verifying Checksum ... OK
  75. Boot reached stage 4
  76. Boot reached stage 5
  77. Boot reached stage 6
  78. Boot reached stage 14
  79. Uncompressing Kernel Image ... OK
  80. Boot reached stage 7
  81. Boot reached stage 8
  82. Command line TAG setup
  83. Params->u.cmdline.cmdline console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
  84. p console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
  85. ## Transferring control to Linux (at address 8492c000) ATAG parameters 8803bb50 - 8803bba8...
  86. [ 0.000000] Linux version 2.6.35.12 (david@sw2-desktop) (gcc version 4.2.1 (ARC_2.3)) #2 Wed Sep 2 17:47:57 CST 2015
  87. [ 0.000000] Parsing ATAG parameters from bootloader
  88. [ 0.000000] ATAG_CORE: successful parsing
  89. [ 0.000000] ATAG_CMDLINE: command line = console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
  90. [ 0.000000] Board id: 65535
  91. [ 0.000000] ATAG_HW_CONFIG_ID: hw_config_id = 65535
  92. [ 0.000000]
  93. [ 0.000000] Processor Family: ARC 700 [0x33]
  94. [ 0.000000] CPU speed : 500.00 Mhz
  95. [ 0.000000] Timers: TIMER1 TIMER0
  96. [ 0.000000] Interrupt Vect Base: 0x88026800
  97. [ 0.000000] Peripheral Base: NOT present; assuming 0xCOFC0000
  98. [ 0.000000] Data UNCACHED Base (I/O): start 0xc0 Sz, 1024 MB
  99. [ 0.000000] ARC700 MMU Ver [2]
  100. [ 0.000000] PAGE SIZE 8k
  101. [ 0.000000] JTLB 128 x 2 = 256 entries
  102. [ 0.000000] uDTLB 8 entr, uITLB 4 entr
  103. [ 0.000000] TLB Refill "will NOT" Flush uTLBs
  104. [ 0.000000] Detected I-cache :
  105. [ 0.000000] Type=2 way set-assoc, Line length=32, Size=16K (enabled)
  106. [ 0.000000] Detected D-cache :
  107. [ 0.000000] Type=4 way set-assoc, Line length=32, Size=16K (enabled)
  108. [ 0.000000] Extensions:
  109. [ 0.000000] MPY: 32x32 with ANY Result Reg MAC MPY: Dual 16 x 16 and 32 x 16
  110. [ 0.000000] DCCM: N/A ICCM: N/A
  111. [ 0.000000] CRC: N/A, SWAP: Present NORM: Present
  112. [ 0.000000] Min-Max: Present, Barrel Shifter: Present
  113. [ 0.000000] Ext Arith Insn: Present
  114. [ 0.000000] Floating Point Extension: N/A
  115. [ 0.000000] On node 0 totalpages: 16383
  116. [ 0.000000] free_area_init_node: node 0, pgdat 857999a0, node_mem_map 85846024
  117. [ 0.000000] Normal zone: 72 pages used for memmap
  118. [ 0.000000] Normal zone: 0 pages reserved
  119. [ 0.000000] Normal zone: 16311 pages, LIFO batch:3
  120. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16311
  121. [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
  122. [ 0.000000] bootconsole [ruby_early0] enabled
  123. [ 0.000000] PID hash table entries: 512 (order: -2, 2048 bytes)
  124. [ 0.000000] Dentry cache hash table entries: 16384 (order: 3, 65536 bytes)
  125. [ 0.000000] Inode-cache hash table entries: 8192 (order: 2, 32768 bytes)
  126. [ 0.000000] Memory: 39928KB available (2139K code,1036K data, 12280K init)
  127. [ 0.000000] Hierarchical RCU implementation.
  128. [ 0.000000] RCU debugfs-based tracing is enabled.
  129. [ 0.000000] RCU-based detection of stalled CPUs is disabled.
  130. [ 0.000000] Verbose stalled-CPUs detection is disabled.
  131. [ 0.000000] clockevent mode switch to [1]
  132. [ 0.000000] clockevent mode switch to [2]
  133. [ 0.000000] Calibrating delay loop... 249.03 BogoMIPS (lpj=622592)
  134. [ 0.115000] pid_max: default: 4096 minimum: 301
  135. [ 0.120000] Mount-cache hash table entries: 1024
  136. [ 0.125000] Starting run_ksoftirqd, stack (thread_info) at 857bc000 cpu 0
  137. [ 0.130000] NET: Registered protocol family 16
  138. [ 0.135000] Topaz heap in SRAM 88016800<->88020000, B2 BASE 17800
  139. [ 0.150000] bio: create slab <bio-0> at 0
  140. [ 0.155000] watch64: 2003/08/22 Josef 'Jeff' Sipek <jeffpc@xxxxxxxxxxxxx>
  141. [ 0.160000] watch64: Enabling Watch64 extensions...done.
  142. [ 0.165000] Switching to clocksource ARC Timer1
  143. [ 0.175000] NET: Registered protocol family 2
  144. [ 0.180000] IP route cache hash table entries: 2048 (order: 0, 8192 bytes)
  145. [ 0.185000] TCP established hash table entries: 4096 (order: 2, 32768 bytes)
  146. [ 0.190000] TCP bind hash table entries: 4096 (order: 1, 16384 bytes)
  147. [ 0.195000] TCP: Hash tables configured (established 4096 bind 4096)
  148. [ 0.200000] TCP reno registered
  149. [ 0.205000] NET: Registered protocol family 1
  150. [ 0.720000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
  151. [ 0.725000] msgmni has been set to 77
  152. [ 0.730000] io scheduler noop registered (default)
  153. [ 1.195000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
  154. [ 1.205000] serial8250.0: ttyS0 at MMIO 0xf0000000 (irq = 48) is a 16550A
  155. [ 1.210000] console [ttyS0] enabled, bootconsole disabled
  156. [ 1.210000] console [ttyS0] enabled, bootconsole disabled
  157. [ 1.220000] serial8250.0: ttyS1 at MMIO 0xf5000000 (irq = 49) is a 16550A
  158. [ 1.230000] brd: module loaded
  159. [ 1.240000] loop: module loaded
  160. [ 1.245000] spi_flash: Force not to support Protect Mode
  161. [ 1.250000] Creating 6 MTD partitions on "spi_flash":
  162. [ 1.255000] 0x000000000000-0x000000020000 : "uboot"
  163. [ 1.265000] 0x000000020000-0x000000030000 : "uboot_env"
  164. [ 1.270000] 0x000000030000-0x000000040000 : "uboot_env_bak"
  165. [ 1.280000] 0x000000040000-0x0000007e0000 : "linux_safety"
  166. [ 1.290000] 0x0000007e0000-0x000000f80000 : "linux_live"
  167. [ 1.295000] 0x000000f80000-0x000001000000 : "data"
  168. [ 1.305000] spi_flash: SPI flash driver initialized successfully!
  169. [ 1.310000] ruby_health loading
  170. [ 1.315000] HBM pool: emac rx 0x0 to 0x8000, wmac rx 0x8000 to 0xa000
  171. [ 1.860000] HBM meta: emac rx 0x62e040 to 0x6ae040, wmac rx 0x6ae080 to 0x6ce080
  172. [ 1.865000] topaz_hbm_init_pool_list pool 0 pool_list 0x88000000 bus_range 0x6de400 to 0x26de400 sz 4096 count 8192
  173. [ 1.865000] topaz_hbm_init_pool_list pool 1 pool_list 0x88008000 bus_range 0x26ee400 to 0x48ee400 sz 17408 count 2048
  174. [ 1.865000] topaz_hbm_init_pool_list pool 3 pool_list 0x8800a000 bus_range 0x0 to 0x0 sz 0 count 4096
  175. [ 1.870000] topaz_busmon_init success
  176. [ 1.875000] topaz_temp_sens_init success
  177. [ 1.875000] u32 classifier
  178. [ 1.880000] input device check on
  179. [ 1.885000] Actions configured
  180. [ 1.885000] Netfilter messages via NETLINK v0.30.
  181. [ 1.890000] nf_conntrack version 0.5.0 (623 buckets, 2492 max)
  182. [ 1.895000] ip_tables: (C) 2000-2006 Netfilter Core Team
  183. [ 1.900000] TCP cubic registered
  184. [ 1.905000] NET: Registered protocol family 10
  185. [ 1.910000] NET: Registered protocol family 17
  186. [ 1.915000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  187. [ 1.920000] All bugs added by David S. Miller <davem@redhat.com>
  188. [ 1.930000] Freeing unused kernel memory: 12280k freed [8492c000] TO [8552a000]
  189. [ 1.935000] Common mmap addr-space starts 2b0f0000
  190. init started: BusyBox v1.10.3 (2015-09-02 17:38:19 CST)
  191. starting pid 57, tty '': '/etc/init.d/rcS'
  192. [ 2.425000] load_module: 'bootcfg' using DRAM (offset:0x85910000, size:0x8b94)
  193. Starting portmap: done
  194. Initializing random number generator... done.
  195. Starting network...
  196. [ 3.095000] load_module: 'rtl8367b' using DRAM (offset:0x86340000, size:0x28c68)
  197. [ 3.100000] rtl8367b: module license 'unspecified' taints kernel.
  198. [ 3.105000] Disabling lock debugging due to kernel taint
  199. [ 3.135000] load_module: 'emaclib' using DRAM (offset:0x85948000, size:0x4b74)
  200. [ 3.250000] load_module: 'switch_tqe' using DRAM (offset:0x85960000, size:0x489c)
  201. [ 3.300000] tqe_descs_alloc: 256 tqe_rx_descriptors at kern uncached 0x550a8808 bus 0x80016808
  202. [ 3.375000] load_module: 'dpi' using DRAM (offset:0x862fe000, size:0x1ab4)
  203. [ 3.395000] load_module: 'fwt_if' using DRAM (offset:0x8788e640, size:0x1084)
  204. [ 3.430000] load_module: 'fwt_ctrl' using DRAM (offset:0x86300000, size:0x23f7c)
  205. [ 3.490000] load_module: 'switch_emac' using DRAM (offset:0x862f4000, size:0x1b70)
  206. [ 3.540000] topaz_emac_init, emac0
  207. [ 3.540000] topaz_emac_init, emac1
  208. insmod: cannot insert '/lib/modules/2.6.35.12/extra/topaz/switch_emac.ko': No such device
  209. modprobe: failed to load module switch_emac
  210. No Ethernet interfaces found
  211. Using IP address 223.254.253.252
  212. Netmask is not set
  213. ifconfig: SIOCGIFFLAGS: No such device
  214. ifconfig: SIOCSIFHWADDR: No such device
  215. /sbin/ifup -a
  216. ifconfig: SIOCGIFFLAGS: No such device
  217. ifconfig: SIOCSIFADDR: No such device
  218. ifconfig: SIOCGIFFLAGS: No such device
  219. ifconfig: SIOCSIFADDR: No such device
  220. Starting inetd ...
  221. PCIe target enabled
  222. [ 4.510000] load_module: 'qdpc_pcie' using DRAM (offset:0x86400000, size:0x7680), SRAM (offset:0x88017e28, size:0x1f84)
  223. [ 4.555000] topaz_vnet version 1.0 Quantenna Communications Inc.
  224. [ 4.560000] Random stuff 53
  225. [ 4.565000] ATU outband region 2 (Host BD): EP(0xcffd0000->0xcffeffff) Host(0x5ee40000->0x5ee5ffff)
  226. [ 4.570000] Tx Descriptor table: uncache virtual addr: 0xcffd0000 bda_rc_tx_bd_num: 180
  227. [ 4.575000] Rx Descriptor table: uncache virtual addr: 0xcffd05a0
  228. [ 4.580000] EP Handled idx: uncache virtual addr: 0xcffd11a0
  229. [ 4.585000] RC tqxqueue wake flag address: uncache virtual addr: 0xcffd11a4
  230. [ 4.590000] EP pm state address: uncache virtual addr: 0xcffd11a8
  231. [ 4.595000] PCIe MSI Interrupt Enabled
  232. [ 4.620000] pcie0: Vmac Ethernet found
  233. [ 4.625000] Waiting for host start signal
  234. [ 4.630000] Enable DMA engines
  235. [ 4.680000] Connection established with Host
  236. [ 4.685000] tqe_descs_alloc: 4096 tqe_rx_descriptors at kern uncached 0x56140000 bus 0x06440000
  237. [ 4.695000] tqe_pcie_netdev_init: tqe_sem_en 0
  238. [ 4.825000] device pcie0 entered promiscuous mode
  239. [ 4.845000] br0: port 1(pcie0) entering forwarding state
  240. [ 4.850000] br0: port 1(pcie0) entering forwarding state
  241. Starting wireless...
  242. Loading modules
  243. [ 5.240000] load_module: 'qtn_debug' using DRAM (offset:0x8646f400, size:0x378)
  244. [ 5.310000] load_module: 'i2cbus' using DRAM (offset:0x862f4000, size:0x1acc)
  245. [ 5.420000] load_module: 'qtsens' using DRAM (offset:0x8640d000, size:0x70c)
  246. [ 5.505000] load_module: 'pm_interval' using DRAM (offset:0x8648c000, size:0x1308)
  247. [ 5.620000] load_module: 'wlan' using DRAM (offset:0x86580000, size:0x7ab04)
  248. [ 5.890000] wlan: 0.8.4.2 (0.9.3.3)
  249. [ 6.040000] load_module: 'auc_fw' using DRAM (offset:0x8788c040, size:0x10f4)
  250. [ 6.135000] load_module: 'radar' using DRAM (offset:0x864a0000, size:0x19c48)
  251. [ 6.195000] load_module: 'qvspmod' using DRAM (offset:0x85980000, size:0x10114)
  252. [ 6.290000] load_module: 'qdrv' using DRAM (offset:0x86600000, size:0x8fbd0)
  253. [ 6.530000] Auc SRAM start 0x88040000 end 0x88070000 size 196608
  254. [ 6.535000] Auc SRAM bank 0 start 0x88040000 end 0x88050000
  255. [ 6.540000] Auc SRAM bank 1 start 0x88050000 end 0x88060000
  256. [ 6.545000] Auc SRAM bank 2 start 0x88060000 end 0x88070000
  257. [ 6.620000] load_module: 'wlan_xauth' using DRAM (offset:0x8646f000, size:0x2a4)
  258. [ 6.700000] load_module: 'wlan_ccmp' using DRAM (offset:0x86414000, size:0x16d4)
  259. [ 6.795000] load_module: 'wlan_tkip' using DRAM (offset:0x86410000, size:0x2588)
  260. Loading MuC driver (qtn_driver.qtn_ruby.0.bin)
  261. Waiting for Wireless Events from interfaces...
  262. QCS API error 22: Invalid argument
  263. Found power table in /etc/power_tables
  264. [ 7.715000] QDRV: power table checksum for /etc/power_tables/tx_power_QSR1000_eu.txt
  265. [ 7.745000] QDRV: power table checksum for /etc/power_tables/tx_power_QSR1000_us.txt
  266. [ 7.900000] set power_selection 0
  267. [ 7.905000] qdrv_soc_publish_params: parames->tqe_sem_en 0, auc_tqe_sem_en 0
  268. [ 8.085000] MuC: g_tqe_sem_en 0
  269. [ 8.090000] MuC: build date Sat, 01 Aug 2015 00:19:46 -0700
  270. [ 8.095000] MuC: slow heap begin=0x001fce20 end=0x0037ce20
  271. [ 8.100000] MuC: fast heap begin=0x80030800 end=0x80037000
  272. [ 8.105000] MuC: stack start=0x8003efc0 sp=0x8003f720
  273. [ 8.110000] MuC: calstate is 3 (prod), dcache on
  274. [ 8.115000] MuC: RFIC version 1
  275. [ 8.185000] qdrv_mu_stat_init
  276. [ 8.205000] MuC: bb_init: FEM 0x5 bw_mode 0 chan 0 11b 0 11a 1
  277. [ 8.210000] MuC: rf_optimizing_rf_register_map, set rf to 0x75
  278. [ 8.215000] MuC: WMAC0: hal fd start=0xe5040300 count=48 size=108 end=0xe5041740
  279. [ 8.225000] MuC: WMAC1: hal fd start=0xe5140d50 count=8 size=84 end=0xe5140ff0
  280. [ 8.230000] MuC: dynamic one-bit autocorrelation enabled
  281. [ 8.235000] MuC: freq 1 proj 1
  282. [ 8.240000] MuC: QMAT SRAM base 0x80070000
  283. [ 8.245000] MuC: enable IRQs
  284. [ 8.245000] MuC: AuC enabled 0xe5101be4/0x6005a8b8 il 0xe5101288/0xe510128c stats 0x600591f8/0x6005a5f80x6006d59c
  285. [ 8.250000] MuC: Can't allocate more fcs for AuC. Bad... WMAC = 1
  286. [ 8.255000] MuC: Update MU debug flag from 0x00000000 to 0x20000000
  287. [ 8.260000] AuC: Update mu flag : 0x20000000. Max delay = 0
  288. [ 8.270000] qdrv_mac_reserve_clear: mac reservation table cleared
  289. [ 8.285000] se95: probe of 0-0049 failed with error -121
  290. [ 8.295000] QDRV: no external temperature sensor found
  291. [ 8.315000] QDRV: hardware is 4x4 11ac FO RGMII/PCIe QV840
  292. [ 8.320000] MuC boot succeeded 0.135 seconds
  293. [ 8.565000] load_module: 'wlan_scan_ap' using DRAM (offset:0x8653c000, size:0x2278)
  294. [ 8.705000] MuC: freq 1 proj 1
  295. [ 8.710000] MuC: qtn_mu_ndpa_alloc: bw_cap 0 done
  296. [ 8.725000] Warning: heap_sram_alloc failed to allocate 0xc10 bytes from caller 8598129c
  297. [ 8.735000] VAP create succeeded 0.020 seconds
  298. [ 9.205000] MuC: calibration ver 0x801
  299. [ 9.210000] FWT: [58:8b:f3:66:33:e2] add entry, port:pcie node:0 entries:1
  300. radar in 80MHZ mode
  301. Version of /proc/bootcfg/qtn_regulatory_db.bin is Regulatory db version: v0
  302. Version of /etc/qtn_regulatory_db.bin is Regulatory db version: v37.3.0.21
  303. Selected database version: Regulatory db version: v37.3.0.21
  304. Using /etc/qtn_regulatory_db.bin
  305. dfs_s_radio 0 dfs 0 non-dfs 0 scan 0
  306. Jan 1 00:00:10 iwevent: 00:00:10.387608 wifi0 Set Channel=0
  307.  
  308.  
  309. Setting mode to 11ac80
  310. Jan 1 00:00:10 iwevent: 00:00:10.491539 wifi0 Set Channel=0
  311.  
  312.  
  313. Jan 1 00:00:10 local_regulatory_get_tx_power_info[490]: channel 120 doesn't exist in power table
  314.  
  315. Jan 1 00:00:10 local_regu[ 10.350000] DFS_s_radio: parameters updated, region: eu
  316. latory_get_tx_power_info[490]: channel 124 doesn't exist in power table
  317.  
  318. Jan 1 00:00:10 local_regulatory_get_tx_power_info[490]: channel 128 doesn't exist in power table
  319.  
  320. radar start with regulatory eu
  321. Jan 1 00:00:10 802.11d Set country code[490]: Region EU, Disable country IE support. Region name should be a country name.
  322. [ 10.965000] device wifi0 entered promiscuous mode
  323. [ 11.090000] Enabling SSDP flooding
  324. Configuration file: /mnt/jffs2/hostapd.conf
  325. Using interface wifi0 with hwaddr 58:8b:f3:66:33:e1 and ssid "chal5ghz"
  326. [ 12.055000] FWT: [01:00:5e:7f:ff:fd] add entry, port:pcie node:0 entries:2
  327. Jan 1 00:00:12 iwevent: 00:00:12.718689 wifi0 Set ESSID:"chal5ghz"
  328.  
  329.  
  330. [ 12.560000] MuC: ### relocatable RX code flag 0 ###
  331. [ 12.565000] MuC: 16, 32, 16
  332. [ 12.565000] MuC: 16, 32, 16
  333. [ 12.570000] MuC: 16, 32, 16
  334. [ 12.570000] MuC: 16, 32, 16
  335. [ 12.575000] MuC: rx_post_init: free 0 rxq 9 9 394 descr 0x8000f000/6592 cache 0x8002ca00/13184
  336. [ 12.580000] WPS: push button is not configured
  337. [ 12.590000] br0: port 2(wifi0) entering forwarding state
  338. [ 12.595000] br0: port 2(wifi0) entering forwarding state
  339. Beamforming enabled
  340. 802.11ac Enabled
  341. Jan 1 00:00:13 iwevent: 00:00:13.386391 wifi0 Custom driver event:SCS: stats task is started
  342.  
  343.  
  344. SCS disabled
  345. QTM: load profile off
  346. [ 13.555000] qvsp_strm_reset: stream reset
  347. QTM enabled: 0
  348. [ 14.930000] [2]Dump register set "Packet memory"
  349. [ 14.955000] [6]Dump register set "Global control regs(2): RX frame processor regs"
  350. monitor led
  351. [ 15.410000] br0: no IPv6 routers present
  352. [ 15.505000] qdrv_radar_is_rdetection_required: ERROR - channel not yet set
  353. [ 15.510000] pcie0: no IPv6 routers present
  354. [ 15.565000] Build name: v37.3.0.50
  355. [ 15.570000] Build revision: 34345
  356. [ 15.575000] Build type: SDK
  357. [ 15.580000] Build timestamp: 1438413743
  358. [ 15.590000] Platform ID: 450
  359. [ 15.590000] Hardware ID: QV840
  360. [ 15.595000] Hardware revision: bbic4_rev_a2
  361. [ 15.600000] Band: 5GHz
  362. [ 15.605000] Kernel version: 2.6.35
  363. [ 15.610000] Calibration version: disabled
  364. [ 15.615000] DC/IQ cal version: V8.1
  365. [ 15.615000] Power cal version: V8.1
  366. [ 15.620000] MuC firmware: qtn_driver.qtn_ruby.0.bin
  367. [ 15.625000] DSP firmware: rdsp_driver.0.bin
  368. [ 15.630000] AuC firmware: auc_driver.0.bin
  369. [ 15.635000] MAC address 0: 58:8b:f3:66:33:e1
  370. [ 15.640000] MAC address 1: 00:00:00:00:00:00
  371. [ 15.645000] U-Boot version: v37.3.0.26
  372. Carrier ID 0, uboot update flag 0
  373. [ 16.205000] MuC: Update MU debug flag from 0x20000000 to 0x00000000
  374. [ 16.205000] MuC: MU enabled
  375. [ 16.205000] AuC: Update mu flag : 0x00000000. Max delay = 0
  376. sh: missing ]
  377. /scripts/cmdloop starting /sbin/call_qcsapi_rpcd, at 00:00:16 up 0 min, load average: 0.42, 0.09, 0.03
  378. /scripts/cmdloop starting /sbin/qcsapi_rpcd, at 00:00:16 up 0 min, load average: 0.42, 0.09, 0.03
  379. /scripts/cmdloop starting /sbin/qcsapi_rpcd, at 00:00:16 up 0 min, load average: 0.42, 0.09, 0.03
  380. /scripts/cmdloop starting /sbin/call_qcsapi_rpcd, at 00:00:16 up 0 min, load average: 0.42, 0.09, 0.03
  381. 'monitor_temperature' is not enabled/set
  382. MAUI Service started....
  383. [ 17.095000] RADAR: CAC started for channel 104 (5520 MHz)
  384. Jan 1 00:00:17 iwevent: 00:00:17.322312 wifi0 Scan request completed
  385.  
  386.  
  387. Jan 1 00:00:17 iwevent: 00:00:17.324397 wifi0 Custom driver event:RADAR: CAC started for channel 104 (5520 MHz)
  388.  
  389.  
  390.  
  391. dhcp service is not enabled in wireless_conf.txt
  392. Starting httpd
  393. bind: Bad file descriptor
  394. bind: Bad file descriptor
  395. starting pid 884, tty '/dev/console': '/bin/sh -l'
  396.  
  397.  
  398. BusyBox v1.10.3 (2015-09-02 17:38:19 CST) built-in shell (ash)
  399. Enter 'help' for a list of built-in commands.
  400.  
  401. quantenna #
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!